Multi-Dish install

[islandtime]

I have been having a problem getting the 110 Sat. for quite a while, but after reading, I have found I may have a problem with the IRD. It does not take me to a specific menu. Here is the exact problem, after going to MENU on the Remote control, then selecting SYSTEM SETUP, and then INSTALLATION, I do not see MULTI-DISH INSTALL. The Ird always takes me back to the POINT DISH and SIGNAL STRENGTH window showing me the 119,110 and a few other Sat's. The ATTENTION window for mounting and positioning complete never did come up. Is this a Ird problem, and can it be fixed? I am able to get 119 without a problem but not 110 Changed LNB's and switches as well but always get the same results any help is appreciated.

Thank You

[SimpleSimon]

You don't say which receiver model you have, nor what type of LNBFs and switches, nor whether you've done a "Check Switch". All of these are important pieces of information that are needed before we can help you.

[islandtime]

I have a 3700 IRD (2800 is the same thing isn't it? Have the same problem with it as well) Legacy LNB's sw 21 switch connected and have done numerous switch tests. The 119 is recognized on the Odd and Even but never the 110. Can't be the LNB because I have switched them and the signal comes in on the number 2 side as well when switched but only the 119 Sat Dish 500 with a Dual bracket holding the LNB's. Thank You

[Smith, P.]

Your software can be obsolete.

[SimpleSimon]

What's Check Switch reporting? port #s, the whole thing. Maybe your 110 LNB is pointing at 119?

[islandtime]

SimpleSimon
Not sure will have to check, will be back after work.

Thanks for the Many responces. This is what I am doing, and still no 110. I go to MENU (on Remote) SYSTEM SETUP INSTALLATION, DISH-POINT SIGNAL, then to DISH POINT and SIGNAL STRENGTH PEAK ANGLES. All this does is take me to a Azmeth, Elevation, Skew Dish300, Dish500, and Super Dish option Window, I cannot seem to get to the MULTI-DISH 2 bar Window showing both signal bars for the 110 and 119. I have done 3 or 4 different switch tests and sometimes it will detect the 119 but never the 110.

Thank You again

[boba]

On your DISH 500 you have a plastic "Y" adapter that the LNBFs are attached to if you look at the top it is marked 110 & 119. Cover the 110 with tin foil and see if you are still getting 119. If you lose 119 you have the wrong LNBF pointed at the satellite. If this is what has happened leave the tin foil in place and reaim the dish then run the switch check after you find the 119 on the 119 LNBF and you should get the DISH 500 tuning bars.

[rk69rn]

Boba is right.
I have installed 100+ sats.
The easiest way without a signal meter is to aim in one at a time with the old legacy lnb's.

Here's what you do.

-First verify that your support arm is plum.(straight up and down where the dish is attached.
-make sure all settings are correct(azimuth,elevation)
-cover or remove the 110 lnb(it's marked on the yoke)
-leave the switch off for now and attach cable to 119 lnb
-aim until you receive 119 sat signal with good atrength.
-remove cable from 119 and attach to lnb on 110 side.
-99% of the time 110 will be there
-connect switch to both lnb's(even if no signal at 110)
-run a check switch
-if only one sat picked, go back to step one and make sure everything is correct.

note: 119 and 110 are approx. 2-3inches apart at the lnb's, so if you get 110 when you want 119, then move over a couple of inches.

Hope this helps.
RK

[ViROID]

If your dish was working to begin with and you've lost the 110 all of the sudden then your SW21 is probably going bad. Swtich the two lines from the LNB's at the switch, if your 110 shows up and your 119 dissapears then this confirms that your switch is bad. If it doesn't, then either you have something obstructing the view or the dish is off alignment.

[islandtime]

Again,Thank You for the many responces. I have tried to switch the LNB's from 110 side to 119 side on the sw21. When I do this,I get no signal at all and after a switch check I get "No switch Detected" but if I put them back to the original setting (119 at 1 and 110 at 2) and do a switch check IRD tells me 119 is there on 1 and 2 (X"s) also says "Warning only one Sat. is connected" I am beginning to think it is a bad switch but I have two and got the same results with both. IRD tells me I am hitting the 119 (Green Bar) Thank-You again