QQ-Box USB DVB-S Tuner - Unknown Device?

**Solomine** · 02-16-2010 12:02 PM

http://www.ktzit.com/

is the manufacturer i think.

I send them a a mail before the holiday. I hope they answer some questions when they are back. The 22 februari they get work again.

I have contact with a guy Ariel, he is verry helpfull. He come's also back on the 22th februari

**1ADAM12** · 02-16-2010 01:41 PM

Originally Posted by Solomine

http://www.ktzit.com/

is the manufacturer i think.

I send them a a mail before the holiday. I hope they answer some questions when they are back. The 22 februari they get work again.

I have contact with a guy Ariel, he is verry helpfull. He come's also back on the 22th februari

That is not the QQ Box. I had one of those and it had a bad tuner. I returned it to China and got my money back.

**Solomine** · 02-16-2010 05:20 PM

This is the TV-S02 the QQ-box is the TVS05 a newer type.

Shenzhen Futian SEG Plaza Excellence Exploiter Electronics Business Department - USB VoIP Phone, IP Camera, DVB Terrestrial

or

DVB-Satellite direct from China (Mainland)

**1ADAM12** · 02-16-2010 07:38 PM

Originally Posted by Solomine

This is the TV-S02 the QQ-box is the TVS05 a newer type.

Shenzhen Futian SEG Plaza Excellence Exploiter Electronics Business Department - USB VoIP Phone, IP Camera, DVB Terrestrial

or

DVB-Satellite direct from China (Mainland)

Can you open your receiver and take a picture to post?

Please confirm LME2510c as IC onboard.

**1ADAM12** · 02-18-2010 08:42 AM

This tuner uses a STx0288 Chip hence the LME 0288 driver.

**1ADAM12** · 02-18-2010 10:54 AM

The current QQ Box 05 version works when the metal enclosure is removed.

**1ADAM12** · 02-18-2010 11:58 AM

Fix the 05 by adding a strip of electrical tape to the USB end of the board.

**Solomine** · 02-20-2010 09:08 AM

Like you can see is this one with a LME2510c chipset and a sharp tuner

I go try of the QQ-box works when the metal enclosure is removed and adding a strip of electrical tape to the USB end of the board.

**1ADAM12** · 02-20-2010 11:33 AM

Good Pics.

I checked all the solder connections and all look good. There is alot of Fiberglas dust on the board that you can clean off with an air hose or artists soft bristle brush.

If you can remove the box end plate at the USB side, you can apply the tape to it.

**killergaboca** · 02-21-2010 05:50 AM

Originally Posted by 1ADAM12

I tested the receiver with ProgDVB (current version)and it works good.
With DVB Dream it works the best. when you boot DVB Dream it automatically selects the LME driver. It's like the two were made for each other.
Both programs find the current driver LME.......7395 version 2.0.1 and load while ignoring the older LMEDVBS.DLL driver.

1- if Unknown USB error message, it is most likely the crystal or the tuner, the uP is the more reliable.
2- if low signal check the LNBF voltage while scanning. If it does not shift between 14 and 18 volts, the tuner is most likely bad.
3- if red lock led is on always, its a bad tuner.

I have my qq box since friday and of course it's not working. In windows xp media center, with dvbdream or else. The informations of getting it work are seeded everywhere on this forum, and the links are not working plus writing in shortens are not helping for a newbee. I thought it's not needed to be a programmer to use a tv player in windows.
Is there a conclusion in this forum with driver download links and explanation about qq box vs. human kind/xp?