Recent content by voomvoom

Nope I don't have any ka lnb's, so I can't try for them I have thought about trying them in the past, and you now have me thinking again but, I probably won't.....

If I remember correctly, Skywalker 1 was in a box, mine is blue, it has 3 ports: a coax to connect to lnb, a port for an electric cord for power, and a USB port to connect to computer the Skywalker 2 looks like a PCIe card, it slides into a PCI slot (I think it will go into both a PCI or a...

I have a Zinwell WB-68 6x8 Multi-Switch (WB=Wide Band) label has: Wide-band 6x8 Multi-Sw Part#:WB68 Ka/Ku bands 250-750 MHz 950-1450 MHz 1650-2150 MHz Lot:70901 DirecTV-approved part I use it with Norsat 3220 lnb's on the non-KHz side for C-band and with Norsat 4106a lnb's on the...

I have several devices with hdd or ssd, most are 1 TB drives I have 2 @ 2 TB ssd's, they are external (enclosed) with one in an sf8008, the other with my osmio4k+ most of the drives are WD's, the one in my mio is a Samsung 860 evo I only have one that has it's own power supply, the ones in my 2...

I had a similar problem with openpli software update a couple of days ago openpli was installed on slot 2, after the update and reboot it got stuck on the openpli boot logo it was like someone had pushed the pause button and it froze there the remote was useless, nothing I tried would work so I...

http://www.linkboxusa.com/

I use pure2 6.3 on my 4k+, the one I loaded was "osmio4kplus-PurE2-6.3-20191215_usb" I don't recall any issues loading it. Their may be a newer version if you look? Don't know what you mean by any differences? They are all different one way or another, but also pretty much the same? It has...

Threshold: As you can see in my snapshot, I have this particular LNB set for 12700 This gets me to the OFF side of my multi-switches 22 KHz (I think?) Also the Tone mode set to OFF does this (I think?) Not sure if both are needed? I use a threshold setting of 11700 for the ON side of my...

LOF1 should be 10750 LOF2 should be 10750 not sure about Switch if you mean Diseqc, it would depend if you have a diseqc switch or not no switch would be 0 if you have a Diseqc switch, it would depend on the port you are using? Hope this helps... Al EDIT: Diseqc itself has settings of 1.0...

I don't find that odd at all? Do a manual scan for any frequency you have numbers for that didn't show up in the scan. If it still doesn't come in..... Then it would be odd to me...!!

I remember ONN, didn't remember or care where it was located, sort of moot since it's been gone forever..... I also remember Orion, they had two channels as I remember, I assume east and west. I really wouldn't know, as they were both scrambled. Also, I have no clue where they were, nor do I...

have you tried reboot of your receiver could be it (receiver) just needs to catch it's breath? Al

This is correct, if you have windows, go to the whatever it's called in the left/lower corner, the box to type a Search with enter backslash, backslash, ip address of your receiver, backslash, root it would look similar to this \\10.0.0.8\root that should bring up the files from your receiver...

It's inside of the sf4008

Absolutely This site is full of Kind People RICH with Knowledge More than willing to help when they can Makes me feel Richer And I'm certainly Blessed for there HELP..!!!!