Help setting up World Direct dish with Manhattan Skyline 1000 for 3ABN

Hi Guys,

I gave up on the little 18x20" dish and got a larger world direct dish with 1 linear, and 1 circular lnb.

I am having trouble getting any kind of signal at all though.

the dish just arrived today, and i spent a couple hours trying to get signal, but have had no luck.

Here is what I have:

World Direct dish, mounted on flat surface, using a tripod.
the dish has 1 circular, and 1 linear lnb (unhooked the circular one)

My location is Aberdeen, Washington 98520

Clear line of site

I have looked online and found the satellite co-ordinates:

Full-screenAddress: Aberdeen, Washington
Latitude: 46.9754°
Longitude: -123.8157°
Satellite: 101.0W AMC 2, 4 | DirecTV 8
Elevation: 31.6°
Azimuth (true): 150.1°
Azimuth (magn.): 132.8°

I have tried pointing in that direction using a compass, but cannot pick up anything at all: 0 signal, 0 strength

I have tried setting up the Manhattan Skyline 1000 receiver as per the directions from Adventist Satellite website:

Manhattan Skyline 1000

[SIZE=+2]FTA Satellite Receiver Programming[/SIZE] This guide will assist in programming your receiver to enable reception of 3ABN Television, 3ABN Latino, 3ABN Radio, RADIO 74, ATN HOPE, ATN Business, LifeTalk Radio, LLBN and many other Free To Air ( FTA ) broadcasters.
Before attempting to program new channels it may be necessary to make adjustments to the dish and/or LNB to obtain a strong signal that reflects good signal and quality levels. Poor signal quality will affect the ability to program and properly receive additional channels.

[SIZE=+2]Adding New Transponder Information[/SIZE]
[SIZE=+1]On Satellite AMC-4 (GE-4)[/SIZE] 1. Using the remote control, press the [SIZE=+1]MENU[/SIZE] key, then press the right [SIZE=+1]VOL[/SIZE] key, the INSTALL box will highlight.
2. Press the down [SIZE=+1]CH[/SIZE] key once, and highlight 2. CHANNEL SEARCH. Now press the [SIZE=+1]OK[/SIZE] key, and the CHANNEL SEARCH window will open.
3. Press the down [SIZE=+1]CH[/SIZE] key 4 times until TP DATA is highlighted, then press the [SIZE=+1]OK[/SIZE] key. A TRANSPONDER DATA window will appear, on the right, with TP1xxxxxx) at the top in yellow.
4. Press the right [SIZE=+1]VOL[/SIZE] key until TP(x): USER DEFINED appears in yellow.
5. Press the down [SIZE=+1]CH[/SIZE] key once, and highlight FREQ. Enter the frequency (i.e. [SIZE=+1]11983 [/SIZE]for ATN / LifeTalk)in the box.
6. Press the down [SIZE=+1]CH[/SIZE] key twice, and highlight Symbol Rate (S/R). Type the Symbol rate (i.e. [SIZE=+1]05900 [/SIZE]for ATN / LifeTalk).
7. Skip to step 8 if the Polarization is correct ( Horizontal for all of the Adventist channels). If it is not correct, press the Down [SIZE=+1]CH [/SIZE]key to highlight POLARIZATION and change.
8. It will take up to 15 seconds for the SIGNAL and QUALITY bars to turn green. Press the down [SIZE=+1]CH[/SIZE] key several times until STORE is highlighted in yellow. Press the [SIZE=+1]OK[/SIZE] key once and the TRANSPONDER DATA window will disappear.
9. Press the down [SIZE=+1]CH[/SIZE] key twice and highlight START. Press the [SIZE=+1]OK[/SIZE] key once and the receiver will automatically store the new channel(s), power off and repower.
Repeat these steps for each transponder that is to be programmed.


But still nothing.

Would someone have the patience to teach me what i'm doing wrong?

I would very much appreciate any help you would have to offer.

Thank you very much
Shnippy

hi,

thank you both for the quick reply.

i hadn't thought about the skew. it is still set at 90. that would be a big problem, is that correct?

the receiver, well thats another story. i bought it brand new, and while playing around with it, i set it to factory default. it still has tp information in there, and it does have 3abn, but it doesnt seem to match anything i have seen online.

when going to the antenna setup, it gives me 4 options:
Wide low 9750 high 10750

Universal low 9750 high 10600

Single single 10750

Single-s single-s 5150

then there is a setting for lnb power options: Off, V/H, 14v skew on, 18v skew on

then 22khz Tone On,Off

then DiSEqC Off,1,2,3,4,Mini A, Mini B

then 12v On,Off


Then under channel search i have it set up like this:

Search index 1
Satellite GE_4 (101.0w)
Search Mode Auto All
TP Data TP13 3ABN (i set this) The TP Data is:FREQ 11983, POLARITY H, S/R 5900, FEC AUTO, VIDEO PID 00000, AUDIO PID 00000, PCR PID 00000
LNB SKEW SAYS -45
POSITIONER NONE


Again, i am new this and am in need of some of your expert advice.

I guess i might need it explained to me like im a second grader. of course these kids are very bright these days

Is any of the information i have given pertinant enough to help me get this set up?

Thank you both again for offering your assistance.

Thanks,
Shnippy

Hi Anole,

So 19.9 deg counterclockwise from behind. I will set it to that.

any idea what lnb i should set the receiver to? wide, universal, single or single-s?

Thank you again for helping.

Shnippy

oops.. sorry, i was looking at your reply quickly at work, and didnt see it.

im going to give it all a go after work today.

thank you very much, and i will post back when it is set up.

very cool!

thank you,
shnippy

hi guys,

had another go at it today, but it didnt work.

got a steady 70-90% signal strength, but 0 quality, an no channels.

any extra help would be great greatly appreciated.

thank you all very much

shnippy

i have it set to 5700 as in the instructions from 3abn, but looking at this from lyngsat, is that for susbscribers only?

1822 H
tp 6 3ABN DVB 5700-2/3
North and Central America P Smith
090525

3ABN English 11160 1120 E
3ABN Latino 21260 1220 Sp
3ABN Radio 3 1122 E
Radio 74 Internationale 4 1230 E

should i have it set to 1160 for fta?

thank you,
shnippy