Search results for query: *

ive installed dozens of hopper/joey systems and have not had a problem doing downloads on multiple joeys at a time as long as hopper has fully downloaded with Client ID...if this is causing people issues the problem is likely elsewhere...unfortunately Dish greatly underestimated multiple hopper...

The tech have meant you would have better los closer to the house...the eastern arc signal is not "less" than western arc...mpeg4 simply requires less signal

77 is only used for some locals and dish latino...The sattelites on installation screen mean nothing as far as install goes dont worry about that.After running checkswitch if pointed properly you should see 61 and 72...the downloads come from 61 so you can still do downloads but many channels...

You can use a sling link adapter for VIP reciever to hook it up to the Internet as it uses home wiring to distribute the signal. You can use a Phonex Easyjack 2 to transmit your phone line through the electrical wiring. You can also use dishcom modem to transmit phone line through electrical...

It is very likely dish will have LOS as they have 2 arcs to choose from.However the high def 129 has a low 30 degree elevation which can sometimes be a problem.The eastern arc however points ruffly 45 degrees to the left of the western arc and its lowest elevation orbital is 61.5 at 36...

There never goin to be exactly the same.Im not sure what there -/+ is for the inputs but most electronics are at around -.5/+.5 so that variance should definetly be fine.But the voltage being fine doesnt justify the reciever nput is good.The input has to be bad

It will work.You will need to activate the new recievers,setup the new remote controll addresses and set the remotes up to work with the TV's. TV2's may not be on the same channel anymore. To be sure they do go into the menu to 6-1-5(modulator setup) Make sure the the new reciever has the...

Nope.It would be the same as running 2 line directly from the LNBF.It doesnt care what input it goes in.It should work in either. However it does not work to run 2 single tuning boxes off a seperator cause there is no DPP single tuner(just a side note) but if your running to a dual tuner its...

make sure you do hard reset and then try and if still the same its the reciever

it would have to be the reciever.If you ran a direct line to Input 1 from the LNBF and got nothing and it worked on port 2 it has to be the reciever

Problems in the line can just as easily cause this.Just yesterday I fixed this issue with a customer as they had a low frequency barrel in the line that eventually began to burn out.Here is a list of things to check for as they can be the problem. -Low frequency barrel -RG59 coaxial cable...

Some power saving newer tv's give off an IR signal through the room to detect lighting and adjust screen brightness accordingly.This IR signal does effect some UHF signals. Try disabling "Dynamic Contrast" or disable the "energy saving" option if equiped. Or move antenna THE EXTENDED ANTENNA...

Using an I bracket your getting prime focus.With a y you have an offset giving you less gain

Good luck

Why do you think there is a problem.Are you missing channels.

Samsung LN52B630 In this case it would probably be the bottom HDMI port that has DVI next to it.The top composite audio inputs likely go with it.

Newer TV,s even my walmart vizio do have a composite hookup for hdmi on at least one of the hdmi inputs.This being due to the fact that lots of older surround sound systems do not have the hdmi output or in my case using a dvi to hdmi converter would need another way to run sound as dvi doesnt...

all even and odd transponders come down together as far as the signal coming into the dish is concerned.If your getting 15 and 16 then your getting the rest.What does your check switch say? Even though Point Dish goes from 1 to 32 you wont get alot of them. Are you peaking with the reciever...

Im selling a few extras on Ebay right now: Dish Network 21 UHF/IR Remote "Brand New" - eBay (item 120514323839 end time Jan-10-10 13:49:03 PST) If your just using it for the learning feature the 20.0 will be fine. If your wanting UHF and TV2 capabilities then you will need the 21.0 remote

Doing this you will not get as good signal strength.The y bracket has an offset so your skew will not be 90 either as the twin has a 4.5 degree offset per orbital to pick up orbital 110 and 119.

Yep,diplexers work fine with splitters.I do it all the time. Just put the splitter on the vhf side of the diplexer and it will mirror like the diplexer isnt even there. The vhf side of the splitter can be manipulated the same ways the coaxial output of the reciever can be.

You can use red and white composite cables from the audio output on the reciever to the HDMI audio input on your tv.

Can you be specific on all the equipment you have and are all tv,s needing high def? If all 3 tv,s need high def you will need 3 seperate lines from the LNBF for each reciever. If even 1 tv will be standard def you can simply replace one of the recievers with a dual tuner that will work in 2...

-Make sure its a splitter and not a diplexer.They look the same but a diplexer will say diplexer on it and it will have labels in/out,sat,vhf instead of a splitter which is in,out,out -Switch the tv's and see if the problem still exists on the same tv.If so its a tv problem. In this case: -set...