Search results for query: *

Plenty of units on ebay for under $200, a few go for under $100. That would get you 2 channels via a headphone track. For full audio sound, you would also need a Dolby DP569 - "reasonably" priced on ebay too. However, I don't think NBC uses DolbyE. DolbyE uses just one audio pid with serveral...

A Dish Network dish is pointed to a Dish Network Satellite, to get Dish Network - which you have to subscribe. FTA channels are on other Satellites, which you need a larger Dish, and different LNB.

You're killin' me Smalls

You already have AZBoxes, and a good Sat Card. I don't think a Mini ME will get you anything that you are missing.

ebay.com - search dvb-s2 android I have a stand alone Android "TV" Box (non DVB), it's fun to play with ... games, YouTube, make a "dumb" TV "smart". Where it lacks is in streaming - it can't handle an HD feed, even on Gigabit Network.

Yes - when the Dish rotates, the skew is taken care of.

One of my motors will not run unless an LNB is connected

Remove the cable from the Motor to the LNBF, leaving cable from Receiver to Motor connected, and try moving Dish.

It's the process that's confusing - 'cause you "think" you know what you need to do. :) I think I used NotePad to write the complete commands with the IP numbers, so you can copy and paste into Putty window. Again - Pumpkin is just a server which is accessed by the AZBox.

Slowly coming back to me...... PumpKIN is the FTP Server. When following the PuTTy directions, you are accessing your PC running PumpKIN to retrieve files that are saved onto the AZBox. You set PumpKIN's "root" directory to the location of the 3 recovery files. Hope I am helping.

In PumpKIN.... Set the "root" directory to something simple "C:\RecoverAzbox\Files" Select - Allow access to sub Select - Give all files Click "OK" Bottom Right Corner of PumpKIN window - select Server is Running

It has been a long time since I did the recovery, but I remember being confused with using PumpKIN too. From what I Remember - PumpKIN is installed as a Server on your Computer, and you tell the AZBox to download a file.

I do not believe there is any update for the ME.

What version are you running now?

I think those are Inclined or Declined - not in the same plane as the other Sats (no good for aiming a Dish for TV) Use AMC9 @ 83w. You will be 1.5 degrees off to start. Then setup receiver for USALS, have it move to 83w, and readjust Azimuth 1.5 degrees to the East for peak signal. 11840 H...

It's your neignbors! just kidding

You need to confirm that you are actually getting 30e. Even though the receiver is set for 30e and you have a TP locked, you can still be on the wrong Sat. Scan the channels on 30e, and compare to this site http://www.lyngsat.com/Arabsat-5A.html - do the channels match?

What does this have to do with Chucks problem / resolution?

The receiver does not actually know where it's pointing. When aiming the Dish, it's all up to you to align mechanically. Tell the Receiver to go to 29e - your South Sat (the Sat that is closest to your Long - 29) Then go to Dishpointer.com, enter your location, pick 29e from Sat List, and click...

I have him in Kuwait. 29N, 48E

Which Sat did use align too for "south"? Also, what City, Country are you in - just to double check you Long / Lat

If memory serves me, this a an AZBox firmware issue long ago. Which firmware are you running in the AXBox?

It's not a 22KHz for sure

What type of Switch - DiSEqC or 22KHz

My GBox would react to DiSEqC Switch commands - could be a switch issue, or that I use positions 1,2,3,4 on the GBox. We drifted of OP topic, but since he has not responded, should we assume he got it working?