Search results for query: *

With 2 C LNB's you do not need to have a controller to run the servo motor to change polarities. The two outputs can run into a multiswitch for more than two receivers and the polarity is switched by the voltage selecting multiswitch input 1 or 2. No servo motor sticking in the winter...

May be great for now, but with many here, once you get it setup and then have a channel breakup... you then look for a bigger dish.

Just to be clear..... With only one set top box, connect to port one, result? Now disconnect this set top box and connect to port two, result? Now, disconnect this set top box and use only the second set top box Connect to one port, result? Now disconnect this set top box and connect to port...

Is the reed switch close enough to the magnets? When to far away it may produce a pulse (close open sequence) when the motor is turned by hand or slowly, but not have enough magnetic strength to close the switch when turning at a fast speed. When it was giving the errors before the reed switch...

Can the reed sensor turn in the white plastic triangle? If so, any difference if you turn it... say 30 degrees.

Be sure to check first if lithium batteries can be shipped to your location. i.e. I see most parts places in the U.S will not ship them across the boarder. You can always try Sayal, they have a few locations including Markham. http://www.sayal.com/zinc/index.asp or Global...

What some people will do to eliminate rain fade on their pizza sub....

First make a drawing of the current wiring for it can be put back after you test the sensor. If you disconnect the blue and black wires from the sensor (the black tube above the magnet wheel) that go to the terminal block for there are no connections to the sensor, then hook an ohm meter to...

Thanks, (that was sure quick) I will backup my settings before removing my receiver and loading that file. It will make finding MeTV and THIS a lot easier when I go over there.

Yep... thats all Once I have that tuned in with my receiver, then I can put his receiver back in and program in the channel. Just wanted to make sure all the parameters are correct for I am scanning for the channel and not for blank space.

Well my friend with his C-Band dish has not been able to tune in MeTV or THIS since the change over to 101. I only have Ku myself, so am asking if someone could help me out with a Channel Master file with MeTV and THIS for 101. I am planing to go out to help him in another week and would like to...

Is there any statement from Motorola that the satellite receivers were included in the sale? Motorola could of very easily kept the satellite business and only let the cell phone end of the business go. Do we know for sure that the satellite business was included in the sale?

tvropro, even though some of us are not able to financially help out or even help with the programming, I, and I'm sure many others greatfully appreciate your hard work.

Will Map Master work with parallel port BDM devices (specifically the P&E micro cable 16/32 P&E Microcomputer Systems - CABLE_16/32 - CPU16/3xx BDM Interface (5V, Parallel Port) - 68HC16, CPU3xx, Interface Hardware/Cable that was supported with the 4PLAY software) or just the USB device?

The manual is in the download section, look for "Motorola 922 4DTV", page 26 and 27 explain the connections. M1 and M2 are the motor power connections, +5, PULSE, and GND are for the motor sensor. If your motor sensor only has two wires, then you will only need to connect PULSE and GND. If your...

The DVD recorders do not have any ir blasters so you would have to turn the H2H satellite box to the channel you want to record as well as set a timer or press the record button on the DVD recorder. There is also no program guide so it either set a timer for the input and start and end times, or...

You can use a computer with a capture card and a USB-UIRT to change the channels. Then most of the PVR software should work. Just check first to see if you can create your own lineup. I use BeyondTV for my OTA recordings. I have not tried it with my satellite box, but it should work as you can...

Sounds like great success so far. Are you able to backup what is currently in the memory, and then after making your changes able to restore to that backup after loading new channels and satellites? I know some would say why would you want to go back to what you initially had, but for those...

Well he moved the disk slightly and was able to get THIStv. (on 87.0) It appears it is weaker than the other transponders.

The next time I'm out to his place I will have to try adjusting the skew and bumping the dish. He is currently getting THIStv on G16 on the Caribbean channel, but that overlay of theirs is so big and anoying. I can't have a C-band dish where I am, so for me it Ku only. He doesn't have Ku, so we...

I was visiting a friend who has C-Band (I only have Ku) trying to get MEtv and THIStv on 87.0 AMC 3. We could get other transponders on that sat, KMCCW was one channel I remember seeing, but could not lock the transponders for MEtv and THIStv. I was using the parameters posted in TheList! (see...

Found it.... I had forgot about that one.

Is this posted somewhere? If so, can you provide a link please?

The 4PLAY should still download the maps, just the map export to text file and inport back to the bin file does not decode the data properly. 4PLAY should still be able to download and restore the maps from the bin file. 4PLAY just backs up the memory chip where the maps are stored. For other...

Does anyone have a save of their DSR920 memory map with the 4PLAY program with the generics in it? Even if the 4Play can not decode the saved file to a text file, all the data should be there in the saved file and it should be able to restore the generics to a receiver with no generics.