Search results for query: *

I recently found at swap meet a fta receiver labeled ASTV USA Noolix NX-5500 HD. It seems to boot up and front panel says START but I cannot with front panel or remote control get it to do anything. Would anyone have a user manual for it or point me to somewhere that nay have one and or a...

Looking for a fta service call for a older lady that has g19 for international channels. I have retired so do not do this any more. If interested you may call her at PM me or admin for number or you may call Matt at PM me or admin for number (who was her tech but does not work anymore due to...

Absolutely not. just trying to bring unit back to life. No front display, no video out either ntsc or pal (use old black/white tv with vertical hold adjust to view pal mode). I see there is no one here that can help. MODS please close this thread.

I tried updating firmware on a openbox s10 and it is now dead, no display. Checked power supply and it is good. Tried using a rs232 program (PVR 800 Hd tool) used for boot repair of S9, even though it uploads the files, unit is still doa. Is the boot for the S9 the same for the S10? Does anyone...

Most in-motion dishes use a legacy lnb, which is not compatible with the solo node/Hopper

I have just tested the Omegasat 6000u with software version 1.21 and it works for RTP by changing the FEC to DVB-S2. drjohn

The new rtp channel requires a FEC rate of 8/9. I do not believe that the Amiko can do that fec. drjohn

Loader for coolsat 7100 is the same as the coolsat 7000. Just found at another sight. Have used it and loaded 7100. Thanks for all the help. drjohn

Thanks for the reply, however,it does not work. USB thumb drive only good for update if unit can come on. Also following this thread http://www.satelliteguys.us/free-air...i-cleanse.html you get a 404 error, thread not found. Coolsat 4000,5000,6000 loader does not work the 7100. Will keep...

I have just inherited a coolsat 7100 micro pvr and it will not come out of standby. Power supply voltages look clean, so I would like to load the coolsat 7100 v1.16 firmware, however, I cannot find the STB tool to load with. The coolsat 4000,5000, and 6000 STB tool does not recognize the 7100...

As I repair some receivers, I believe your problem is power supply filter caps going/gone bad. Look at power supply board and check for bulging, rounded tops, not flat tops on the capacitors. Replace any that are rounded. drjohn

I have been a c band repair service in San Diego, Ca since 1985. I am going out of business and want to give a good home to all the manuals I have from the c band days. I have manuals, both user and repair, on almost any equipment manufactored since 1980.These include Amplica, Toki, Chaparral...

I will return the box. drjohn

system ifo shows date of june 15 2012. I do not want to deal with eyepatch group for files. Dont want my name on there for maybe future FBI perusal. Maybe not software problem, dont know enough to tell, however, I need to start somewhere. drjohn

4 month old Limesat HD receiver picking up G19 only. Unit now shows only 20% for both signal and quality. Checked on second dish and does same thing. After a little investigation found the following. The signal and quality shows 20% with or wothout an LNB cable attached. All power supply...

I am pretty sure your solo node is bad. If you can, do a substitution using your duo node and see if you get signal. Or, since you are directly behind the dish, disconnect one host from your duo node and connect your hopper to it to see if it works, or put your solo node temporarily into your...

Ebay has ROC Multi-sat remote for (.95 free shipping to run the coolsat 7000. drjohn

On page 28 of the 9704 troubleshooting guide, it shows an aux cable that can be run from dome to a secondary receiver. connect a cable from aux out to tuner 2 of the vip 722 and you should not have any more problems. drjohn

I havea X2 receiver. It did not come with G19 in memory (only european satellites). I had to add the satellite name and then wrote in one known active transponder for that satellite in order to aim my dish.

Thanks but I have the latest firmware and channel editor. I guess I will build my own NA database. appreciate the reply. drjohn

Hi: I purchased a unit also but need a NA sat list. would you be willing to share your list? or point to where I can download it? thanks drjohn

Have a replacement sonicview 360 premier that I am having a hard time to get the same channel numbers as before. The last sonicview I had , had software version 1.14 in it and when the G19 channels were downloaded, they downloaded to channels 1000-upward. Now this receiver downloads to channel...

The 21.0 remote can learn codes of the original toshiba tv remote. check here: EKB: 2-way Remote, for programming instructions. My Hannspree tv was same way, but was able to have the 21.0 learn the hannspree remote for all functions. drjohn

I tried a sathawk 800 (sadouns version of the openbox s9) and was not able to get the channels also. A Sonicview 8000, however, does and the channels show as 480i. , which the openbox cannot do in Mpeg4. drjohn

Would anyone have the last "factory" file for the VS2000 platinum/lite along with the newest sat/info file. I have a platinum receiver with files from 2005 on it. I really need the latest or newest sat/info file. ViewsatUSA is no more. I have looked using Google but everyone that has files are...