Search results for query: *

It's also on my cable provider....... Adelphia....Not a Voom problem.

Sony XBR800 4 x 3 HDTV....DVI.....Excellent PQ..... Go Voom!

I was only connected with the flat type phone cord on the STB end.....never knew the other end wasn't connected until I decided to investigate while the STB caller id function wasn't working....when I plug the other end to the phone wall jack box.....Lockups Galore.... Using the round high...

Use the round high speed DSL phone line with a DSL microfilter.....and hopefully that would limit frequent lockups to a minimum plus your caller ID function will now work. YOU'RE WELCOME...........

While trying to get the caller ID function to work,...I discovered the installer hadn't plug the phone line from the STB to the wall jack....Hmmmm....so I did the honors and LOCKUPS galore, before this no lockups....I hard booted 3 times in five minutes. So I changed the flat phone line to the...

Antennas Direct on the web...lots of antennas to choose from in different range categories. And forget about using the diplexers....have the cables run independently.....this will increase signal strength to your OTA antenna.

Try Cables To Go on the internet.

Clarification: The Diplexor is the coaxial connection on the back of the STB. where both antenna cable use one connection. The small gold-colored connection with the AC plug is for your OTA antenna amplifier. By disconnecting the diplexor and running each cable independently to its proper...

This is all about picture quality........and getting the most out of your display and the Voom STB......I own a 4:3 set....if I set 1080i with the remote control my SD will be stretched even in pillar box format because the STB thinks all channels are HD. All channels have top and bottom bars...

If you have a diplexor get rid of it....signal strength is stronger when both antennas run on it own coaxial cable. Try purchasing your own OTA antenna......Antenna Direct DB8 did it for me....I'm 62 miles away from the LA tower between mountain ranges, houses, trees, etc. 90+ signal.

Shelly's Answer......... The Voom exclusive are in 1080i, what I'm saying is the STB by some flaw reverts back to 720p when changing channels when Native mode is set using the STB red manual button only. Using the menu's red colored 1080i button with the remote locks 1080i but stretches the...

Using Native Resolution with the red STB button only, reverts back to 720p on HD channels when switching channels....using the 1080i red button in the Installer Menu Locks ALL channels in the 1080i resolution, so your SD channels are Stretched......These steps allow you to use Native resolution...

Hopefully this helps: Using Native Resolution on a 4 x 3 HDTV on the HD channels has black bars top and bottom....on SD Channels the screeen is full....On a 16 x 9 wide screen HD set the screen is full on HD channels, and the SD channels have black bars on the sides of the picture....Native...

Hopefully this helps: Using Native Resolution on a 4 x 3 HDTV on the HD channels has black bars top and bottom....on SD Channels the screeen is full....On a 16 x 9 widescreen HD set the screen is full on HD channels, and the SD channels have black bars on the sides of the picture....Native...

Try Both....Experiment.....Try the Native Resolution steps using both HD modes...........

Try Both....Experiment.....Try the Native Resolution steps using both HD modes...........

After pressing OK you leave the screen with the colored buttons, press OK again to return to the colored button screen...then press the red button on your STB for Native Resolution....Press OK again....then proceed to back out....Let me know what happens...because this lock in 1080i HD in...

To SET 1080i in NATIVE RESOLUTION WITHOUT the SD Stretch... 1. Enter system settings from the Setting Menu. 2. Enter INSTALLER MENU 3. Enter INSTALLATION WIZARD 4. Enter SET OUTPUT RESOLUTION 5. Set output to 1080i; Press OK. The next screen Press OK again. You must be at the screen...

I agree with your statement...except when you use the red button to set Native mode the STB output to 720p....how do I know?....Quick Test....Set Native Resolution using the manual red button.....Go to the Installer Menu....Enter screen "Set Output Resolution" it should say, "1080i DVI"...

These steps are for those who want to use 1080i in Native Resolution. The STB tends to revert to 720p in Native Resolution....why?......design glitch.....Try the steps and see.....be sure to press OK after the Four line lights illuminate momentarily.

It's hard to tell 1080i from 720p on without testing.....I've notice the when you enter the "Set Output Resolution" screen after you press OK the bottom of the next screen ask you to 'Press OK to continue in 720p".....that alone led me to believe that in Native Resolution the STB want lock on...

This is only for those wanting to use Native Resolution......

There no need to reboot.....follow steps thru 6...the four light will blink momentarily then press OK to set the 1080i for the HD channels....the SD channels will look clearer....If you don't press OK as the final step the STB will convert back to 720p......

1080i NATIVE RESOLUTION without the SD STRETCH! To SET 1080i in NATIVE RESOLUTION WITHOUT the SD Stretch... 1. Enter system settings from the Setting Menu. 2. Enter INSTALLER MENU 3. Enter INSTALLATION WIZARD 4. Enter SET OUTPUT RESOLUTION 5. Set output to 1080i; Press OK AND REMAIN at...