OTHER Splitter question

jy2

Member
Original poster
Oct 30, 2018
6
3
Baltimore, MD
If I connect only two outputs of a 4 way splitter (Steren 201-244), do I get 1/2 or 1/4 strength of the original signal on each output? In other words, can a 4 way splitter serve as a 2 way splitter when only two outputs are needed?

I understand that the signal strength of each of the 4 outputs is 1/4 of that of original signal. I want to know if that holds true regardless whether an output is used.
 
If I connect only two outputs of a 4 way splitter (Steren 201-244), do I get 1/2 or 1/4 strength of the original signal on each output? In other words, can a 4 way splitter serve as a 2 way splitter when only two outputs are needed?

I understand that the signal strength of each of the 4 outputs is 1/4 of that of original signal. I want to know if that holds true regardless whether an output is used.
All outputs of a 4 way splitter will be the same,-7db,regardless of how many outputs are used.If you only need 2 outs use a 2 way,-3.5db.A 4 way splitter is essentially 3, 2 way splitters.
 
Unused ports = wasted IF signal. It is best to use the appropriate splitter.
Just to clarify, there's no appreciable loss from using 75 Ohm terminators versus using a smaller splitter. In other words, you can have a 4-way splitter that is properly terminated on 2 outputs, and it would perform "basically" the same as a comparable 2-way splitter.
Edit: I should add that it makes no difference within reason. You only start to push the boundary when you are splitting frequencies near 2GHz by 32 ways. I can't imagine a scenario where you would be using a combination of splitters with 30 terminators and no amplification, but it's funny to think of.
 
Last edited:
Just to clarify, there's no appreciable loss from using 75 Ohm terminators versus using a smaller splitter.
To reiterate, your claim is false.

The loss is substantial and it is known from the specifications for the splitter. Using a four-way with dummy loads on all unused outputs reduces output signal on all ports by 7dB versus 3.5dB for a typical two-way splitter. In percentage terms, each output of a typical two-way splitter is approximately 44.7% of the input signal. The output of any port on a properly terminated four-way splitter is just 20% of the input signal.

Terminating resistors reduce loss due to impedance mismatch and interference from stray signal but they absolutely do not turn a four-way splitter into the equivalent of a two-way.
 
Agreed, termination resistors on unused ports do not reduce signal attenuation on used ports. The loss on each port is fixed whether terminated or not.

Also, I may be stating the obvious, do not use a terminator on a power passing port. On powered ports, use a cap without termination.
 
  • Like
Reactions: primestar31
On powered ports, use a cap without termination.
Good warning. That said, I note that not terminating all outputs reduces power transfer due to impedance mismatch over and above the loss of unnecessary splits. It is best to use the appropriate splitter.
 
I think it should also be mentioned that using splitters on satellite systems is a bit unusual, as the communication between LNB and receiver is bi-directional (voltage-controlled polarity, 22 kHz, Diseqc) and those commands by one receiver could conflict with another receiver.
 
  • Like
Reactions: a33 and Titanium
I think it should also be mentioned that using splitters on satellite systems is a bit unusual, as the communication between LNB and receiver is bi-directional (voltage-controlled polarity, 22 kHz, Diseqc) and those commands by one receiver could conflict with another receiver.
This has recently become more of a thing as the Orby TV subscription service uses only one polarity and quite a few of the Orby TV denizens here are/were using FTA antenna gear with their receivers.
 
  • Like
Reactions: Brct203

OTHER 90cm HughesNet Ka Dish for FTA?

OTHER Free to a good home

Users Who Are Viewing This Thread (Total: 0, Members: 0, Guests: 0)

Who Read This Thread (Total Members: 1)

Latest posts