Search results

  1. J

    Win a FORTEC MERCURY II from Sadoun!

    Maybe just my time to win something besides a can of beans. Unit would go good with my fortec antenna.
  2. J

    At9 Antenna info please?

    Have the info I needed. Thanks
  3. J

    At9 Antenna info please?

    Have ordered the H20 receiver from DirecTV. They will install the new AT9 antenna next week. The mounting post rail on my deck is 5 inches wide. Made up of one 4X4 post plus a 2X4 post nail together. I needed that width for the older 3 LNB antenna mounting pad bolt holes to fit. My question is...
  4. J

    Pansat 6000 Question

    If I delete all of the TP's, one at a time, this will clean out all channels? Then I can do a clean (Blind Scan) for this Satellite. Is this correct? Thanks
  5. J

    Pansat 6000 Question

    Is there a way to delete just one satellite and/or just the channels on that SAT, without doing a factory reset? I want to blind scan the SAT. Will that just add duplicate channels? Or will it just overwrite the channel list? Thanks
  6. J

    Pansat 6000

    Your right! Thanks for your input. JackR
  7. J

    Pansat 6000

    Not using the timer function, just setting record function from EPG, should I put into standby mode or leave the STB on? Does it make a difference which? JackR
  8. J

    Pansat 6000

    After setting up recording function, must you leave unit turned on, or can you click the off button and put it in standby? Will it turn on and record from standby? Thanks JackR
  9. J

    Two Receivers-/one splitter?

    About 40 Feet. Is there such a thing as a 3 way high freq switch? Would like to add a 3rd unit at a later date. Only ONE unit running at any time.
  10. J

    Two Receivers-/one splitter?

    I would like to run two Pansat 3500s receivers. Only run one at a time. Can I split the signal and if so, with what? Would the two units have to stay in sync regarding what Satellite was used last? I did a search but could not find the information I required. Thanks JackR Pansat 3500A...
  11. J

    LNB setting?

    OK Pete - thanks for the settings. Will try this afternoon. Jack
  12. J

    LNB setting?

    I just installed the Invacom QPH-031 LNB. Can anyone tell me the correct LNB TYPE setting to use. Using the STANDARD setting I get LNB Local-freq- 10750. Using the SINGLE STACK setting I get LNB Local-freq- 10750(V)/10175(H). Equipment: Pansat 3500S Motor SG2100 Invacom QPH-031...
  13. J

    LNB Change over

    I have the new Invacom QPH-031 LNB that I plan on replacing the Invacom SNH-031 with. Should I do a reset before changing or just plan on changing the setting for each satellite, one at a time? Any other pit falls I should look out for? Thanks Jack
  14. J

    Finding AMC-6???

    Thank you Isat for the information. Will try again in the next few days to get better alignment. Jack
  15. J

    Finding AMC-6???

    I am sorry, but I don't understand your reply. I think you were asking maybe someone to PM me with some basic information that I might need in order to use AMC-6 for my True South location. Would really appreciate that information however it is available. Thanks for you reply and time. Jack
  16. J

    Finding AMC-6???

    I live at Lat 41.5N, Long 72W in Woodstock Ct. The Satellite due south of me is AMC-6. Is is possible to get a signal from AMC-6 with my equipment? Pansat 3500S Invacom SNH-031 Windgard 76 Antenna SG-2100 Motorized H-H Motor I have no problem picking up SBS-6 at Long 74W...
  17. J

    Couple of questions!!

    Answer for Number 2 ONLY! You need a HD receiver to even see the channels.
Top