Search results

  1. G

    It's Time To Help Those Who Are Helping Us!

    Motorola DSR 922 Manufactured 2005 I did the four step conversion 4836 channel count Everything sweet, All sat tiles and guide.
  2. G

    Danger 4096 found turned back on.

    i finally call the ppl and they gave me a hit and within 10 seconds it all dropped in. . .still have all my sat tiles :D
  3. G

    Danger 4096 found turned back on.

    since i posted this i was reactivatin and rehittin the receiver because it was just stuck at '0'. . . then my trip startin movin from 0 and its now at 127, the guide is working but no channels but the DMX ones are workin, not even the ones i subbed too. my channel number has not yet moved.
  4. G

    Danger 4096 found turned back on.

    im tryin with this convertion but im not gettin the EMM to move from '0', i sent a few rehits already. how long does it normally take?
  5. G

    SRL Says Alternate Procedure Not Working

    boy what a read. . . i moved my dish over to the W5 sat and im gettin good signal and quality with DC light on, it been about a yr since the 4D was sub to anything. . . when i read the post i see some guys usin the W5 and most sayin to use the X4. what is the difference?
  6. G

    dish sizes

    if you are gonna spend that kind of money might as well add 2 bucks more and get the 21 meter dish
  7. G

    dish sizes

    in my opinion (only based from area) i would have to say not very accurate when it comes to sizes and what you can get in your area. when i looked at it, it seems like i cant catch anything from here lol but i have heaps of birds under lock includin DN sats
  8. G

    what switches do i need?

    can i get a 'yes'? lol lol
  9. G

    10' mesh installation

    my dish is also setup up simular where as i have to be on the roof. . .BUT i knew what i was gettin into so the bottom of the dish is about 6" from the top of the roof so if i need to adjust the LNBs i can do so by either 'spinning' which i use to do but now i position the dish at the top of my...
  10. G

    10' mesh installation

    you should need to adjust the inc/dec but it wouldnt hurt to rechk. also rechk the lnb by measurements i wouldnt touch it till i see whats it doin first. i had to use a sat which was about 2 degrees off which was not a problem. you should set the mechanic limits on the actuator, set the dish to...
  11. G

    How to lift 12' Alum Dish off of the pole and haul on the road

    i wold not risk lifting it down since there is risk of breakin on the other dishes. . .when i went for my 12' mesh the wind picked up a bit things got slightin out of hand for the two guys who lift it off the pole tryin to hand it to the two other guys on the ground. . .with yours now with only...
  12. G

    what switches do i need?

    thanks for all the input so far guys, i was thinkin the same but was not sure which switches work with dn and fta. here is a new picture of what i think you meant, i have not put the power inwserter inplace as yet, but i believe it will go between the ms and the 'V' lnb then plug into power...
  13. G

    what switches do i need?

    thanks i will, thats why i posted up my idea. . .i just need the bigger heads to add on to it what i need. . .this is new teritory here :)
  14. G

    what switches do i need?

    hey, i know this setup can work how its setup up there, but my question is: how do i get the ku circular signal to my fta stb also without disabling the subbed receiver? the invacom will not be off to the side either. . .with this feed its completely centered.
  15. G

    what switches do i need?

    hi guys. . . i have one fixed dish pointed at 119w with an dual aspen eagle lnb up and working with a DN ViP222k receiver with both tv1 and tv2 working atm. The other dish is a BUD which can handle both ku and c band signals and will be pointed at 110w (some of the time) and this is using an...
  16. G

    Automatic Skew?

    sounds like the post starter just needs a pansat 2700a/3500 or one of those older models which can control servo, usals and moves the dish via a dish mover. . .this is what im using.
  17. G

    Wives and BUDs

    My wife is kool with the whole setup once i do my part in or alround the home and she can watch TV when she's ready. . .thats why i got rid of my 4' CM and got 'HER' her very own 6' CM ;) happy wife = happy home. . . and i keep my 10' and 12' mesh BUDs to scan the skies.
  18. G

    Actuator not stoping on exact stored sat

    i use to use a 4DTV receiver to move my dish and i had the same problem, even tried it with my 2 Von Weise Jacks. . . i changed to a VBox-X and reprogram the sat locations and it stops on point! 10' mesh with Von Weise 24" Jack. . . waitin to see how the VBox-X holds up to my 12' mesh and...
  19. G

    How for west on a 24" actuator do you get?

    my clamp is also mounted less than 1/2" from the end. . .with my most west sat comin it with a few bumps out from the 4d. . .i really tired to maximize the jack.
  20. G

    How for west on a 24" actuator do you get?

    i think it maybe better if you asked how much arc/sats do you get from a 24". . . in my case my dish 'normally' start at 135w and head east up to 37.5w without hittin any of my limits. . .von weise 24" i would love a 36" jack so i can really get my FULL arc of 1w-135w :D
Top