Search results for query: problem

That's strange, those are among the strongest signals on both the 1mtr or the 1.2mtr here.

...issues been resolved? At this time the majority of my recording comes from MeTv,Cozi and Escape. Are frequent lockups still a bit of a problem? The IPTV part is likely not of significant interest to me..but the XBMC/KODI may be as I watch some things I miss from the big 3 network apps and...

Same problem here. New satellite and normal skew, still very weak NBC & Cozi. 90cm dish. I assume I need a larger dish to bring in these DVB-S2 signals?

I discovered my HH90 problem, bad cable... and now I can pick up 58w to 125w with most averaging between 85% to 98% signal quality, but 103w's NBC/COZI feeds being the weakest signals averaging 10%

We have firmware that works exactly with microHD receiver and Sling - please update manually by downloading microHD remote firmware = http://hdvrbox.com/up/gs/oldremote/usb_update.bin Unfortunately Sling team is extremely slow in responding to my request to add GEOSATpro HDVR3500 remote...

...key on my remote is messing up horribly, and it isn't dirty contact pads inside. It's a very cheaply made remote inside and coupled with the problem I've had right from day one of how mine chews through batteries within a week or so, I would rather use a different remote altogether than...

I liked this receiver as well, but the tuner's coax connection is very easy to break, I've repaired mine twice before moving on to the HDVR3500. Mine got stuck in the boot loop too, had to try several times via the USB connection before it finally started working again. Anyway, I'm planning to...

...blinking. Because I did not have the TV turned on at the time I assumed all was well. However, the next day I replaced the LNB, which was the problem, reconnected the coax and the light did not blink but the unit also did not boot, it just hung. I took it into the computer room and tried all...

It's Dave, but that's OK, LOL I was trying to find some IPTV links for TV from the U.K, Scotland, Ireland, & Australia mostly. Did not have any luck with finding official links in the m3u8 format. Oh well...

Dan, the problem with some links, they are not encoded up to standard.

...and I finally get a reply... with a mission statement, instead of acknowledgement there may be a bug, results of in house reproduction of the problem, or even just a copy of the older firmware I need, . You say you would prefer to address the issue -- I would prefer that too. I've not found...

yes, seems we're having the same problem. looks like the command line trick to remove files should work. I'm telnet'ing usually from my old Mac that should be painless exercise.

If you're using the editor that I posted up a few posts up, it's probably broken in this firmware. Like I said, I had it working in 9XX, it probably won't work in the current firmware versions because of all the changes. Sorry. :(

I'm having problems upgrading receiver. Using the editor is not much of a problem uploading to the receiver is. I go through all the steps and it looks like is actually uploading but is not. After rebooting the unit none of my changes are in place. What gives.

...into the menus before the box attempts to tune the channel (and then lockup), and allow me to move the motor, etc to temporarily fix it. My problem was made worse because sometimes I would tune to a very strong transponder, and then mysteriously 30 to 60 seconds later the motor would begin...

FTA+IPTV, If you haven't yet sent your box back for warranty yet, there's another person that was having pretty much the same problem as you and he got his 3500 back up and running. Here's a link to the thread he started on it...

We Provide me with your serial number and shipping address in the private message, i will send a replacement and fedex shipping label so you can return the failed unit. This seems to be software failure. At minimum, see if you can start receiver in the forced reset mode: 1. Turn off...

I have seen this problem on another receiver (Amiko Mini HD SE) and the 'solution' was to disconnect the dish cable with the box off. Then I turned the box on and changed to a non-problematic channel. If you don't disconnect the dish cable, the box may go into an endless loop every time you...

...after reboot the box is on the same failed channel and go black. this alone should be fine, but it locks up all other operations, that's the problem. SatTV, the box is now (supposedly) on Channel C, so I can literally do nothing, let alone doing factory restore or rescan or reload the...

1. If you don't mind, back up your channels and settings and do a factory default, then rescan the satellites. Let me know how it went. 2. When operating channel A, can you disconnect the cable going to dish and see if you can operate remote by going to different channels, weather good or bad...

...working(didn't use much on iptv, etc.) first accident: after duly starting the box, watched an usual channel A for a while without problem, then switch to channel B, then the screen turn black, buttons on remote don't work, buttons on box front panel dont' work phenomenum...

I had the same issue when trying this as well...

I'm having a problem since updating to 1339 on Sunday. I'm connected to the internet via Ethernet cable and when I boot the 3500pro it says network connected like usual, but the date and time are sometimes off. The date is correct right now, but the time is behind by exactly 1hour. I can't...

Bump...Someone here must know the answer to this? Welcome to SatGuys, FTA+IPTV! :D

...on above question w/r/t samba connection from MacOS 10.6.8? reading thru the this thread, it looks like this is enabled. below is another problem/bug: I have hundreds of channels stored. natually I took time to change their order in list for better viewing/navigation. but whenever I backup...