Search results

  1. Wescopc

    Traditional Pay-TV Operators Lost 6 Million Subscribers in 2019 as Cord-Cutting Picks Up Speed

    I think Charlie has tried more than most - but he can not control the prices the program producers are charging.
  2. Wescopc

    What diplexer and LNB is needed for DIY install?

    Claude, I agree - I used a multi-switch to make more ports available for additional OTA tv's in the house. Many ways to go! Just answering why I did it my way. Bob
  3. Wescopc

    What diplexer and LNB is needed for DIY install?

    I use the vertical (13 volts) side of the switch hooked to a single LNB. Orby is only vertical signal so this works fine, I use the switch to insert (Diplex) my Over The Air (OTA) signal for my local channels received from a roof top antenna. Bob
  4. Wescopc

    Another Program Guide Question

    Just checked, today is Sunday morning and I get through Thursday morning. This may depend on the local station's protocol. Bob
  5. Wescopc

    Another Program Guide Question

    Yes, the guide works fine. Even if you never activated the receiver. Bob
  6. Wescopc

    What diplexer and LNB is needed for DIY install?

    I use a 3X4 mult-switch - works great - see my signature.
  7. Wescopc

    Fl Orby Install Today ! OTA Antenna Questions.

    The receiver has a built-in diplexer. You will need one for the other end of the cable to join the dish and the antenna. Bob
  8. Wescopc

    Frustrated with Orby

    power passing splitter such as: Perfect Vision Power Passing Wide-Band 2-Way Splitter 5-2300 MHz (PV23-302) from Solid Signal or many others - as long as it passes power on the Orby receiver side of the outputs. Bob
  9. Wescopc

    Web Site Down

    I have been on the phone for two hours with tech support today - I have not been able to sign into my account EVER since Jan 24th. They said 2 weeks ago that they would have the IT department cancel my account - so that I could start over anew that didn't work. They will get back to me later...
  10. Wescopc

    Pluto missing OTA channels in guide on a Roku TV

    Scott - do you have an OTA antenna hooked up to your Roku TV?
  11. Wescopc

    Pluto missing OTA channels in guide on a Roku TV

    Pluto integrates some of the locals - not all - on Roku TVs only. Bob
  12. Wescopc

    Super buddy and orby

    That's why we come here! You are welcome anytime! Bob
  13. Wescopc

    Super buddy and orby

    I tried your way - wouldn't work with single polarity LNB. So system setup : Generic Ku Band H/V Dual Pol LNBF Srd N. Am Ku 10.75 Then manual tune: Vt 13 12100 Freq LNB On 22k off DVB-S 30000 SR enter last before exit Exit Best, Bob
  14. Wescopc

    Super buddy and orby

    Because this is a manual tune - ignore the satellite ID. If you are at the dish with the meter you will need to power the LNB turning it on from the button next to the screen on the right. My picture showed the LNB off, because I was connected through a power-pass splitter (getting power for the...
  15. Wescopc

    Super buddy and orby

    Yes some of your settings are wrong - attached is a picture of my meter settings in manual mode. Once set - press exit and view in peaking mode.
  16. Wescopc

    Super buddy and orby

    I just updated an older SB - it does not show the 117w satellite. However, you can manually tune the SB. I was able to lock on 12100, Vt (13 Volts), SR 30000 shown as "Baud(KSym)" on meter. I was not able to lock any of the three that Brian showed. This is the only TP I could find that would...
  17. Wescopc

    Super buddy and orby

    You need a Super Buddy that does DVB-S2. If you have a Super Buddy prior to the AI Turbo S2 (AI Turbo S2) you won't be able to use it. Bob
  18. Wescopc

    Connect OTA Antenna to Orby Receiver

    No, the diplexer passes voltage (13 volts) for the LNB, not for the OTA VHF Antenna. You would need a separate cable from the power inserter to the preamp/antenna.
Top