Search results for query: *

Try turning off bridging on Hopper. This may work till Dish sends out newer software.

Changing DNS servers worked for me also. Thanks Scott.

Firefly, best show ever.

To manually unpair remote: Hold sat till all light up Hold Recall and 0 for 3 secs Press search Press vol + Press stop Wait 5 secs for tone

This works with factory software only: Reset Joey, when Teardrop cursor disappears hit menu repeatedly to get into menu, select settings, press Play-Play-Stop on remote, scroll to bottom of page and select tools, select Cold NVM Boot, Joey should reset and go back to beginning of install wizard...

Last idea that I have is to unplug hopper and all joeys that are linked to it, then just plug in the hopper and see if it still has pip problem.

Press pip then press swap if needed to bring channel 470 lost signal to foreground and if you cannot bring up guide to change channel try pressing the red reset button at this point with the pip window still open.

Can the channel be changed from within pip?

I like the checkswitch idea because there may be an underlying problem with the signal. I would also try to record 2 things then switch to that tuner via the red button then stop recording and change the channel. This may force the tuner to default to this new channel instead of 470.

My bad, red button is on the remote, it should take you to the tv viewing status screen.

Turn diplexers around at dish, they are backwards.

Hit red button on Joey and select an available tuner or let us know what you see.

Try resetting the hopper first, then once it's back up try joeys.

Is it just me or can you reproduce this bug? From joey I start watching a regular dvr recording, hit stop then live tv, go into menu and select either blockbuster or on demand and the progress meter with sequencing green squares just sits there. To get the tiles to load I hit guide, menu, then...

Hopper spec sheet lists MKV, MP4, Music-MP3, Images JPEG.

Center conductor on 59 is thinner and you can bend it over with your finger tip rather easily, whereas with rg6 you cannot.

May want to try to restore defaults and then connect now in network menu. The result code should be 88-xxx.

722 is $0 or $100 and 922 is $0 or $200 based on qualifying. Call Dishnetwork to see what they can offer you.

Reread first post and am concerned about the 12 feet from switch to pwr inserter as it doesn't meet the minimum of 15 ft. you could try moving it to behind the receiver.

Not sure on testing switch but you could bypass both it and the power inserter then rerun setup set for single tuner and multiswitch instead of swm. Is 771a constant or intermittant as I see this happening during heavy rain? I'm leaning toward bad switch since resetting pwr inserter doesn't...

Have you tried resetting power inserter by uplugging it till green light goes out then plugging it back in? Also found this: 771 Searching for Satellite Main Check: 1) Peaking 2) Line of sight 3) Connections 4) Distribution system 5) Hardware 771A Problem Communicating w/ Dish SWiM power...

L069 is factory software on some new receivers, on initial install after exiting out of pointdish screen it should update to current version along with programming memory,etc. If still not updated I like the turn off for 5 minutes idea where it should show onscreen the software update.

Meter reads excessive current when batteries are not fully charged or weak. As per the birdog.tv website: make sure the meter battery is fully charged by disconnecting it for 10 seconds, reconnect then fully charge. You may also hook up reciever to lnb w/o dpp44 switch for powering the lnb.

Edit your Southpark timer by: Hit DVR button 3 times Select Timers Select on SouthPark Select options Change Maximum Recorded Events from 20 to # Select Save

I have a 508, and have also lost several recordings (both protected and unprotected), however they were years old so I just figured that they had a time limit on them. Plenty of drive space left so that wasn't the issue either.