Search results for query: *

  • WELCOME TO THE NEW SERVER!

    If you are seeing this you are on our new server WELCOME HOME!

    While the new server is online Scott is still working on the backend including the cachine. But the site is usable while the work is being completes!

    Thank you for your patience and again WELCOME HOME!

    CLICK THE X IN THE TOP RIGHT CORNER OF THE BOX TO DISMISS THIS MESSAGE
  1. michaelhoffa

    Software needed to edit tp lists in DBS format?

    Thanks
  2. michaelhoffa

    Software needed to edit tp lists in DBS format?

    I actually have two a pansat 9500 and a openbox S10. thanks
  3. michaelhoffa

    Software needed to edit tp lists in DBS format?

    What software would I need to edit a tplist.dbs file? Thanks
  4. michaelhoffa

    Can anyone recommend a dish mover that uses USALS for under a 100$US?

    Have not any problems getting channels on either C or Ku band with this dish and LNBF combo. It is a BSC621 and appears to be working rather well. Tried just using a single Ku LNB that came with dish and wanted more channels. Thanks Mike
  5. michaelhoffa

    Can anyone recommend a dish mover that uses USALS for under a 100$US?

    Thank-you for all the input, have WS9036ne Dish. OpenBox S10, C/Ku band LNBF. Right now I have a spm-990 motor, but it will only do DisEqc commands. In another post I submitted earlier, I listed the issues I have had with unit. Tried on Pansat 9500hdx also and had same issues, not able to use...
  6. michaelhoffa

    Can anyone recommend a dish mover that uses USALS for under a 100$US?

    Looking for dish mover H to H for 1m dish for under 100$. Thanks Mike
  7. michaelhoffa

    usals vs. diseq 1.2 instructions on how to setup motor on pansat 9500hdx

    Yes, I got two of these motors from the same supplier, and one of them was bad out of the box, moved for 15 seconds then led went out and it failed to move again. I sent it back and just got the replacement.The first one that worked, will only work with DisEqc 1.2 selected in the menu of both...
  8. michaelhoffa

    usals vs. diseq 1.2 instructions on how to setup motor on pansat 9500hdx

    I will check that out. But the same behavior on two different receivers? I tried it with my pansat 9500hdx as well. Thanks
  9. michaelhoffa

    usals vs. diseq 1.2 instructions on how to setup motor on pansat 9500hdx

    Able to use DisEqc with the motor spm-990, picked two sats at both ends of the arc and it will move to both using the receiver. Openbox S10. Now I quess I have to input each one manually and select a new position for each.
  10. michaelhoffa

    usals vs. diseq 1.2 instructions on how to setup motor on pansat 9500hdx

    It started to rain, I will try to setup a few using DisEq settings. I did input my long and Lat where is asked for in the Menu. Thanks
  11. michaelhoffa

    usals vs. diseq 1.2 instructions on how to setup motor on pansat 9500hdx

    OK, I got a new Openbox S10, set up the motor to '0' and reset it. Then told the Openbox to use USALS for all satellites. tried to scan AMC9 and when the receiver says it is moving the motor, it is not. SPM-990 motor from ImpaktProducts.com Not liking this at all. Any suggestions?
  12. michaelhoffa

    usals vs. diseq 1.2 instructions on how to setup motor on pansat 9500hdx

    Found out the motor the guy at Impakt Products suggested does not say in the manual it is usals compatible. I was able to get a few sats programmed in and the motor will go to each one. I have to manually move the dish with the switch and scan each one found and save it. Also of note, once I...
  13. michaelhoffa

    usals vs. diseq 1.2 instructions on how to setup motor on pansat 9500hdx

    Manual for this box not detailed enough. Got ws9036ne, pansat receiver, Ariza tech spm-990 motor, and a C/Ku band LNB BSC621. I had been setting dish to each sat manually, but now have motor described above. I set up motor as instructed. set sat to diseqc1.2 and with signal meter connected to...
  14. michaelhoffa

    FTA in Chattanooga

    Are those pictures of the bracket you received as a replacement? I also have a ws9036ne and the bracket seems off. thanks Mike
Top
Back