Recent content by christloves

Has anyone been able to get the Twinhan Program to work with the HH90 motor and a 1.2 or a 2.0 diseq switch with a qph31 lnb to move the dish and switch between Linear and circular. My fortec classic reciever does it with both the 2.0 and the 1.2 switches. I pick up the linear channels...

I have looked at Progdvb and My Theartre, niether support USALS. Other than the Twinhan software, is there a program that support USALS and Disecq 1.2.

I have the motor (HH90) working perfectly now...... The challange is now to get the Diseq switch working in conjunction with the motor to switch from the Liniar to the circular outputs on the Invacom QPH-31. I notice that the dSeq switch provided by sadouns, is a 2.0 and not a 1.2. Do I need...

Yes, Had to adjust to 279.7 degrees. Tested the 2.0 4 to 1 diseq switch provided by Sadoun's Satellite sales. The Twinhan program does not recognize it. Installed it . Entered 10750 for my first LNB in the Satellite Setup, and 11250 in the second LNB description and scanned a satellite...

Well.............. The Solution to the Usals problem with the 102g Twinhan Pci card. DON't enter your longitude as requested by the Twinhan satellite setup program under Advanced satellite setup. Enter your true south + 100 degrees. In my case where my longitude is 80.3, My true...

I was hoping that SOMEONE had experience using the 102g with a motorized dish. Using the Usals to move to satellite rather than moving manually with move to east or west.

I have no known conflicts as yet running the two cards... The Hauppauge works well in MCE2005 for cable or terrestial, inclusive of the epg.

Present Configuration: 102g on a intel 955 btx board with 2 gig ram. Dual Core Pentium extreme 840 processor. 550 watt modular btx power supply. Hauppage mce200r tuner card . Ati 850 pro. Sata Drives. The 102g is connected directly to the HH90 motor which is connected to a Diseq 4...

Got no problems with the drivers. Did it twice...... The problem I think is setting the EAST and And WEST LIMITS, I may be wrong. How do you set the limits?

I already setup my satellite dish which is a 90cm fortec and a invacom qph31 and using my fortec classic reciever, recieved several satellites. and channels. I Installed a twinhan 102g card in my media center and tried the BDA Drivers. No luck in mce 2005. I then installed the XP drivers...

Thank you SCOTTC98. It was your suggestion that finally got me there.

I Got it! what lo should I use for the circular output on the QPH 31 LNB. I am using 10750 for the liniar... How do I know which satellite transmit in circular vs. Liniar. I recieve several satellites with the motor now.... Now I need to find decent English chanells.... Any suggestions.

No. I first aimed my dish to true south, as best as I could using a hand held compass. Then I used the receiver USALS to turn to AMC 5, long 79, where mine is 80.3. I originally set the HH90 to 26.1 degrees and the dish to 40. Once I was supposed to be on AMC 5, I did the East to West...

Setting the dish elevation to 40.6 can only realy be done after a signal of some kind is found, then the dish is pressured up or down to increase the signal... I tried that, no signal increase. Tried the same with the motor. No signal increase. Tried East to west, got a slight increase. Then...

still Hoping for info on the proper way to set the dish elevation at initial setup and how to measure it , what is the true reference point for the dish elevation measurement and the satellite elevation