Recent content by mr_rye89

  1. mr_rye89

    Comments from a newbie to FTA

    Mary and Tito's on 4th/Menaul Cocina Azul on Paseo, also on 12th/Mountain El Patron on Montgomery Juanita's in Barelas Garcia's
  2. mr_rye89

    Comments from a newbie to FTA

    You might have to go to El Paso to get tex mex, the flautas can be had at a Mexican-Mexican restaurant, I don't know about the deep fried tacos. The Whole Enchilada on the west side does Swiss cheese, tomatillo, and chicken Enchiladas that are great, their owner is from Michaocan.
  3. mr_rye89

    AMIKO Amiko MINI 4K UHD S2X - V1.0.69 Firmware

    Hmm cant get a sniff on my 1.2m dish. I think I'll take my receivers (Amiko Mini 4K, GT Media V9 Prime) and little TV outside and try tweaking the 1.2m dish when its dark. I'm also in the ABQ area and its hotter than a Hoochie Coochie out there!
  4. mr_rye89

    AMIKO Amiko MINI 4K UHD S2X - V1.0.69 Firmware

    I couldn't pick up WPR on my 90cm steerable dish, I have a 1.2m dish parked on 99W I will try later
  5. mr_rye89

    AMIKO Amiko MINI 4K UHD S2X - V1.0.69 Firmware

    Well I loaded up the new firmware on my Amiko Mini4K UHD S2X and Muzak works perfectly. Disecq motor control seems to work too
  6. mr_rye89

    unimesh 12

    I have a Unimesh 10 footer and I was able to toss the dish up on the mount by myself, I don't think I'd try that with a 12 footer tho....
  7. mr_rye89

    Comments from a newbie to FTA

    I might be willing to test, Though my Amiko 4k seems to be on the fritz.
  8. mr_rye89

    WANTED WTB STAB HH-120 MOTOR

    I got a Geosat 1.2m HH motor just holding down a shelf in the shed......
  9. mr_rye89

    Getting into HAM in 2024?

    I put up a 1/4 wave vertical for 20m this weekend, just 16 ish feet of 1 inch EMT insulated with 1 1/4" sch 80 pvc pipe stuck in the ground, 4 16 ish ft wire radials across the ground. If it's still there I'll post a picture.....
  10. mr_rye89

    Getting into HAM in 2024?

    I'm thinking about cobbling a vertical together as I have a bunch of 1" emt conduit and 14 ga wire. Are you guys using a 4:1 un un on your rigs? My tuner has a built in 4:1 balun but that's for ladder line
  11. mr_rye89

    1.2 Meter Commercial Dish

    OK, inscription in the back
  12. mr_rye89

    1.2 Meter Commercial Dish

    I've had this for a while, played with it a bit over the summer, but i am finally getting around to really dialing it in on 99w. It fit on a 3" post that I used for the button hook dish, the feed was set up for a transmitter and a normal Ku LNB, transmitter is long gone but the larger NJRC LNB...
  13. mr_rye89

    Any one not getting the Weigel channels?

    You would think that would be a win for her. A 1.2 Prodelin ain't that big/ugly compared to an 8-10ft dish lol I have a 1.2 meter post office Ku dish to fool around with this weekend. I had the blessing from the post master to dismantle it so no felony.
  14. mr_rye89

    The future of the FTA hobby

    Worst case scenario I'll use my BUD(s) to get weather satellites, been watching saveitforparts on YT, fun stuff
Top