Recent content by zack

  • WELCOME TO THE NEW SERVER!

    If you are seeing this you are on our new server WELCOME HOME!

    While the new server is online Scott is still working on the backend including the cachine. But the site is usable while the work is being completes!

    Thank you for your patience and again WELCOME HOME!

    CLICK THE X IN THE TOP RIGHT CORNER OF THE BOX TO DISMISS THIS MESSAGE
  1. Z

    Titanium Satellite Wanted Titanium Satellite ASC1 Dish Mover With Remote

    I have two remotes I do not use, they do things to my LINKBOX receiver!
  2. Z

    Titanium Satellite Wanted Titanium Satellite ASC1 Dish Mover With Remote

    I hope this link works! https://www.ebay.com/itm/373883089067?hash=item570d2b30ab:g:~3UAAOSweDBh5c2i Starting bid is 19.99$
  3. Z

    Enjoy 107w While It Lasts

    Ctv, 93% quality with a crappy LNBF from somebody in Houston that had bought an 8 foot dish from Tech 2000. HOA! Need I say more? He sent me so many lnbfs, I do not know where they came from! I am sure that Tech 2000 only sold him one lnbf with that 8 foot dish. I think he just threw every one...
  4. Z

    Enjoy 107w While It Lasts

    I am on 107 and all there is the VSE channel. 9000i Linkbox and and a 10 foot mesh dish, My concern is that my Linkbox does not have 119 preprogrammed into its memory! How can I add 119 without going online and comepletly redoing my Linkbox?
  5. Z

    Dual feedhorn

    I want it! Thanks, Zack in Tyler TX
  6. Z

    ASCI Not Moving East!

    Dang it! Put the end of the wire thru the hole in the floor, went outside and found it there, took off pulling it towards my dish, made to the dish only to find out my remaining security wire is 15 feet short! Anybody know of a cheap direct burial security wire? In the meantime I know I...
  7. Z

    ASCI Not Moving East!

    Brian, I left out that after the first time I left the Linkbox powered down! I did not like that click just after turn on, I will take you word for it that my Linbox is causing my problems, garbage in, garbage out! Seems to happen after I use the last channel button a lot more than usual! I...
  8. Z

    ASCI Not Moving East!

    Brian. Please reread the above. Tues, it worked fine for what I wanted to see. First thing Wed morning I new I was missing a few channels that I had not scanned back in since the skew was working again! I started a blind scan on G-16 and waited for it to finish! It went on for a few very...
  9. Z

    ASCI Not Moving East!

    Brian, it has been at least three times you have asked me to open a new post about this! You sent me a new motherboard despite it being out of warranty, that did not fix it! Thank You Again for trying!! When I read about the ASC1 going away I bought one of the last ones available. It sat in...
  10. Z

    Asc1 Not Moving West

    Brian, he swapped the sensor wires, not the M1& M2 wires! Reread his his first post! JFOK, if the ASC1 is able to read counts in one direction, it can do so in the other direction! In other words, the sensor can be hooked up red to white or red to red or white to white, it is always going to...
  11. Z

    Electrical wiring for dish

    Brian from Titanium has given his ok to this product!
  12. Z

    Electrical wiring for dish

    Interesting, BING refuses to go to DuckDuckGo?!!!!!
  13. Z

    Electrical wiring for dish

    I have an old PC, I cleared the browser, and then relogged in, then I found this! https://www.dxengineering.com/parts/dxe-cw1812or
  14. Z

    Electrical wiring for dish

    Now I am exiting everything to find out why BING refuses to go to DX?
  15. Z

    Electrical wiring for dish

    Sammughal I am using this for my skew motor, https://www.homedepot.com/p/Southwire-By-the-Foot-22-2-Gray-Stranded-CU-CL3R-Shielded-Security-Cable-57572199/20472 I am using this for the motor at the dish itself with this, DX ENGINEERING actuator cable!, it has big enough wires for the motor...
See more
Top
Back