Search results for query: *

  1. daveplot

    XM Skyfi2 with home or car kit $49

    Once its added to the family plan you should only be billed 6.99. How long did it take you to get the SkyFi2? Was there a backorder like there was a while ago?
  2. daveplot

    Freq Differences

    I finally got my dish pointed correctly and did a scan of IA-6. Comparing what was found with what is at lyngsat, there are a few differences. For example ABC ABSAT was found on 12051 h and v, where lyngsat has it at 12053 v and 12058 v. There are differences like this on the other channels...
  3. daveplot

    Channel Master 1.1m dish & Stab hh120

    Non-Penetrating Roof Mount For Sale: Used Non-Penetrating roof mount. Give me an offer on it, shipping will be actual price.
  4. daveplot

    Aiming Issue

    Yes, that's what i'm using with a skew of -2.
  5. daveplot

    Aiming Issue

    It's a Norsat LNB set to 10750.
  6. daveplot

    Aiming Issue

    I still can't get any signal. I just checked and rechecked the angle the dish is pointing and it's right at 191.5. The pole is plumb also. Any ideas?
  7. daveplot

    Aiming Issue

    I just did the formula from the manual again, and lowered down the dish. It was actually set at 23.5 deg, when it should be 23.9 deg. Is 189 deg correct for pointing the dish? Looking at the manual for the motor they say to use 180 + 11.5.
  8. daveplot

    Aiming Issue

    I have the dish aimed at SBS 6 (189 deg) and I'm not getting any signal. The motor is set to my latitude at 38.5 deg and the dish elevation is set to 45.5 deg. The level % keeps jumping around from the upper 60s to upper 70s but the quality is at 0. Since this is a used dish the thought...
  9. daveplot

    Aiming Issue

    The zip is 21801
  10. daveplot

    Aiming Issue

    I'm trying to aim my dish with a compass, and every time I get near the metal pole or ladder the compass gets thrown off. Does anyone have any ideas on how to aim the dish? What degree should I be pointing it to? 188? (lat 38.36, long 75.5) Also does anyone know how to return the motor...
  11. daveplot

    Channel Master Dish Question

    I didn't want to see the dish from the front of the house or from the road. Also being mounted here the dish is semi-protected from the wind from two directions.
  12. daveplot

    Channel Master Dish Question

    The neighboring lot is wooded, so I have to get as high as I can. Right now the dish is about 24' off the ground, roughly the same height as the peak of the roof. I am probably going to run some aluminum aircraft cable to the roof peak, and a few other spots. I have a couple hundred feet...
  13. daveplot

    Channel Master Dish Question

    43" Channel Master Dish Installation I finally got the dish & stab hh120 motor up on the pole. The mount is a custom one from U-bolts, 2x4 pressure treated, and 5" galv. lag bolts. It mounts to the 2nd story of our deck. The mount is stronger than the deck, so I'll have to put some lag...
  14. daveplot

    XM Skyfi2 with home or car kit $49

    Does anyone know if I get this, can I add it to my family plan? If so right away or after 3 or 6 months? Would the prepaid service be at the 9.99 rate, and the other 3 months be at the 6.99 rate?
  15. daveplot

    Channel Master Dish Question

    I did see a Muzak receiver in the building, but I haven't grabbed it yet.
  16. daveplot

    Channel Master Dish Question

    Thanks, I'll see if I can come up with a mount like that. The dish weighs about 18 lbs and the mount on the back 7lbs. Looking at the Fortec/Stab motor, the shaft sticks up, where with the SG2100 the shaft sticks down. Is this just how they are pictured, or can the motor shaft stick up or...
  17. daveplot

    Channel Master Dish Question

    I'm trying to figure out how to put a motor on the dish such as a SG2100. When I look at pictures of that motor I don't see how it would work with the mount on the rear of my dish. Is there a motor that would work with my mount, or can I buy a new mount for the dish somewhere? In the end...
  18. daveplot

    Channel Master Dish Question

    I received a Channel Master dish today from a friend and am wondering what I can do with it. It came off an old Wendy's Resturant. By the looks of the numbers on the back it's a 1 meter dish. Channel Master was purchased by Andrew. Looking on Andrew's site this looks like their "1.0m...