Search results for query: *

If that's the case Mike has given good advice in post 2, Personally if its free i would get it and stick this LNB on it and see what you can get, https://www.aliexpress.com/item/32766993520.html The above lnb is far from the best performer but it will give you some C and KU band channels good...

I guess it depends on what dish your talking about, a 8 foot DH/CM dish will wipe the floor with any 1.2 dish in C/KU, please state what dish's you want to compare.

Hi installed the motor last week all is working well very pleased with it.

The Jaeger SMO-SMR 36 was it big brother ive never owned one Themes about AL/EL parabolic positioner for prime focus dish 240 cm in diameter. | CZECH AND SLOVAK DX SATELLITE CLUB The 1224 is a good mover but like ive said stick to a 1.2 dish and its fine and will last years.

1.2 to be safe, it will move a 1.8 channel master but there have been a few cases of it snapping and the dish blowing away, some do come with a metal plate as a extra but it bolts to the aluminum and doesn't do much, I once fabricated a metal cage round the motor and installed a 1.8 on it...

To get round planning permission here in the uk i built a mobile base out of rail track, i had a 2.3 DH sat on it in the picture below, its now been converted to a tilt over wind up movable base with a paraclipse sat on it.

You don't want to be putting a 8.5 ft dish on one of them it will blow away, Cant you concrete a pole in the ground ? if you can make sure you adapt some sort of a leveling system.

Hi a forum members is selling some. Kijiji, eBay, and Craigslist dishes for you to take a look at https://www.ebay.com/itm/Baird-Supporting-Mounts-VL-4-1-8m-to-3-0m-Satellite-NPRM-Poles-CATV-MDU-SMATV/113891172102?hash=item1a84715f06:g:u~sAAOSwvT1dgAtT

8k is coming out a few test transmissions available at this side of the pond. https://www.flysat.com/8k.php Olympic broadcasters are really pushing 8K TV for 2020 in Tokyo https://petertyson.co.uk/lg-oled88z9pla-smart-oled-television

If you have a footprint beaming your way and the correct size dish nothing stopping you getting geting a satellite 0.5 degree, get a VPN and use iPlayer might be an easier way though.

The only transponders available out far west is 65W C band extended I can see further W than that but nothing beamed this way to my knowledge.

Good luck happy hunting, I also like messing with fringe reception ive built a fold down wind up tower the wind up part to try and get me more arc. ,

Personally I wouldn't glue it on i would just do a wrap or two of electical tape/PTFE round the throat make sure it is clean and dry before you do it.

All testing complete the unit is now ready for instillation, ive calculated the full arc time of 180 degree and it works out at 5 minutes 24 seconds that was using a Geotrack gp-1000 positioner the RC 2000C can make this time slower or quicker depending on settings used, obviously my arc is not...

Thanks yes the glass sensor linked is a little on the large size a 30mm would be better like ive said i am trying to source some more local, the items listed would be no use to me ive already used sprockets and a 80/1 to gearbox to slow everything down and the part that's broken is this item...

Hi further testing today while testing the magnetic switch east side packed up it turned out to be the diode (NTE5801) ive located one here https://uk.farnell.com/nte-electronics/nte5801/standard-diode-3a-100v-do-27/dp/1383797 removing the switch i broke the glass on the read sensor after...

Just about finished a few little bits to do, ive removed the stops mechanism from inside the motor and have bench tested it and its working fine, i will time a full revolution tomorrow and calculate the the full arc time.

Hi this link might be useful. PORTAL BSD - SATÉLITES

Hi i got the spigot back today i need to file the woodruff key then it will be ready for installation.

F/D ratio can be calculated here. SatLex Digital :: Technology :: Calculators :: F/D Ratio

Hi your F/D should be set to the information you have and left at that distance, F/D ratio is calculated from your F/D this is the positioning of the scalar, when tweaking the scalar your F/D should be the same distance as when you started, what you need to do is ad washers to move the scaler...

Ive purposely geared it to go slower using a chain and sprockets with certain amount of teeth to slow it right down for fine tuning purposes, I have a RC 2000C unit that has enough pulses to drive it along my large arc also the ASC1 should have enough pulses, Plenty of pictures can be found...

This link should help on how chokes/scalars work How Do Scalar Rings Work Its probably best you state what dish you have the settings needed will be in the specification of your dish it will save messing about measuring and calculating.

Thank you that's good to know.

Any pictures please :-), its going to be a lot of messing around covering and uncovering five 10ft dishes, personally I would get something like a blow heater and go and defrost them as and when needed. blow heaters - Bing images