Search results for query: *

In my opinion, it is foolish to put dish 28' above ground UNLESS there is a line of sight issue. You will have issues with techs accessing dish to service.

Your diagram is correct. It sounds like you do have an amplified antenna. The power inserter for the antenna needs to be placed in between the antenna and the splitter shown in the diagram.

You need to run an additional cable from your dish antenna to your new DISH receiver. What you term "SAT Splitter" is actually a seperator, which allows a dual tuner receiver such as the 722k the ability to use both tuners with one wire. It DOES NOT allow you to split a satellite signal...

Before check switch, you should show signal strength if you tune to 61.5 on signal strength screen. Once signal locks and meter bar turns green, exit out of screen. Hopefully, you will get the screen that asks if your dish is locked down, answer yes and receiver should download new software...

It should be fine. We bury that cable all the time with no problems.

1-800-333-DISH (3474) Hard Drive is toast!

Jay There are three current types of DISH 1000 dishes, 1000.2, 1000.4 & 1000+. The 1000.2 is similar to the old DISH 1000, but with an integrated LNB. It points at 110/119/129. The 1000+ points at 110/118/119/129. The 1000.4 is the ONLY dish in the 1000 series that points to 61.5, being...

Make sure your mast is perfectly plumb. Set your skew to 127, and tighten. There is no need to fine tune the skew setting. Set your elevation to 27. Use a compass to find 245 and roughly aim dish there. Using a meter (or the signal meter in the receiver), slowly move antenna until you get...

Press the mode button on the front of the receiver to change to 'Single Mode'. You will continue to use the remote you use now. You can also disconnect the tv2 connection from your set. When in 'Single Mode', tv2 output is same as tv1.

We do OTA installs (among other things) out in Montgomery City area, and have had great success with Winegard AP8275 preamp. Yes, it makes a difference, at least out in this area. Depending on where you live in Columbia, you may be suffering from multipath as well. If so, a preamp will not...

Phil Do you have a preamp on your antenna? You should have no trouble with KRCG in Columbia with an outdoor antenna. Al

You can add 2 622's with DISHn It Up if you have 2 942 receivers. The upgrade cost is $199/per unit. If you are lucky, exec resolution will allow you to do something similar. Dealer cost for 622 is over $400, so this is your best bet. Good luck

The splitter needs to be between the antenna power supply and the receivers. In other words, the power supply needs to feed a single cable direct to the antenna. If you place a splitter between the PS and the antenna, you will not properly power the preamp. You will then be able to split the...

Yes you can. You will need to split the OTA by the number of feeds needed, and use diplexers to combine the OTA and satellite feeds. You will use another diplexer at each receiver to seperate the OTA and satellite. If your OTA uses a powered pre-amplifier, the power supply needs to be...

I posted same info with link for the bit in your post in the General Satellite/Cable forum Al

Connect another receiver to the other leg of the splitter, and you will find that it will not work, once one receiver gives LNBF a conflicting request.

If you are saying that you had a receiver added to an existing account of the family member, you will violate terms of service by moving your receiver to another location without setting up a new account. Best thing to do is to contact DISH (or better yet, a LOCAL RETAILER) and have a new...

Have your parents remove your name from their account, and find a LOCAL RETAILER who can help you. If your address and phone number are different from your parents, the retailer will be able to set you up with a new account. Best of luck Alan

...duplicate post

Any possibility that a stereo speaker is too close to the tv? It almost sounds like distortion from a speaker magnet. May need for the tube to be degaussed.

Menu 6 3 Info Browse Theme TV/Video Unplug receiver from electrical source for 15 seconds Plug back in and let receiver reboot

We found out the hard way that the 322 needs to be updated first. We always light up the receivers here in our shop before we install with a DPP44. It doesn't take much effort to bypass a switch. Al

In order to drop your HD package, you will have to have your 811 turned off. You cannot have the 811 without the HD package. You are obligated to the service for 12 months following the DISH Mover. Al

No, it is not. The 322's DO NOT have the software for DPPlus installed out of the box. If you attempt to connect through a DPP44 prior to bypassing the switch and downloading updated software, you will be in for a VERY LONG DAY! Al

You need to use the 522 to backfeed to the other room. The 510 and 522 both have RF connections, but the 522 has an agile modulator, which means that not only do you have a choice of RF channels besides 3/4, but the output is greater to allow for signal loss due to splitting the signal, etc...