Search results for query: *

  1. S

    AMIKO Amiko Mini - Goto X function

    The more I think about it, I could probably save the position numbers in the Amiko ahead of time even if the motor is not where I want it to be for each. Then use the meter to peak and store those same position numbers in the motor. Then theoretically it should be all good, since the Amiko...
  2. S

    AMIKO Amiko Mini - Goto X function

    Yes, thanks. :) What I’m looking for is the Goto X function within the DiSEqC 1.2 area. Normally it goes along with the Goto Reference option. Basically it just allows you to drive the motor to one of the positions that is already stored in the motor, without actually saving anything. Here...
  3. S

    AMIKO Amiko Mini - Goto X function

    Does anyone know if the Amiko mini supports the GotoX function where you can tell it to drive the motor to a specific position number that has been previously stored in the motor from another STB or meter? Most STB’s have this option under the DiSEqC 1.2 section, but I can’t seem to find it on...
  4. S

    GEOSATpro Need help setting up USALS with a HH120 motor

    That looks like an SG2100. :)
  5. S

    OTHER HH90 out of range

    So, I was able to get a hold of an SG-2100 motor with the hopes of being able get East rotation greater than 65 degrees. I had downloaded the manual ahead of time and learned that the SG-2100 has adjustable hardware limits, which was what I was looking for. Well, wouldn’t you know it, the motor...
  6. S

    OTHER HH90 out of range

    Yeah, I took a chance and opened the case. :) I don’t see anything physically stopping the movement, but I didn’t want to risk taking anything apart further. From the sound of the motor, it does sound like it is stopping electronically at 65 on both ends. And what I mean by that is, it makes...
  7. S

    OTHER HH90 out of range

    Hi Titanium. That’s what I thought also, however using DiSEqC 1.2 control from my receiver, the motor won’t move beyond 65 degrees on the motor scale. According to the HH90 manual, the electronic limits at +/- 65 and mechanical limits set at +/- 70. I’ve confirmed that all limits are disabled...
  8. S

    OTHER HH90 out of range

    Cool, thanks... I will look this over and digest it before I give it a try. Unfortunately, I was careless and broke my lnb connector yesterday so I’m waiting for a new one to arrive before I try anything.
  9. S

    OTHER HH90 out of range

    Ok, but isn’t what you just described the “normal” motor setup where motor zero is my true south? When I set it up like that, anything lower than 99 west is out of range even with no limits defined.
  10. S

    OTHER HH90 out of range

    Thanks, appreciate it. I may dabble with the temp workaround to try it out. So, with the motor normally pointed to true south, these are the settings I have per DishPointer.com with HH90 selected: Motor latitude = 20.1 Dish elevation = 42 degrees If I wanted to set my 0 reference to 125w...
  11. S

    OTHER HH90 out of range

    Ok thanks... using DiSEqC 1.2, am able to squeeze a few more degrees, but it won’t go past 65 degrees on the motor scale. The HH90 manual says the physical limit is 72 degrees, but I guess my receiver won’t allow it. I’m using a cheapo GTMedia v7s for now. The Erase Limits command you speak...
  12. S

    OTHER HH90 out of range

    Hi all, I just purchased an HH90 to motorize my 90cm dish here in Hawaii. I've done a ton of reading to prepare for this, but I suspect my location is causing a problem. Initially I connected my receiver to the motor and wanted to check the operation to make sure it would be able to move to...
  13. S

    OTHER Ku dish mount elevation angle

    Ok, it’s all starting to make more sense to me now. I flipped the clamp around to the correct position and with the dish face perfectly vertical, the elevation scale reads 24 degrees. So I guess this dish is similar to the geosatpro 90cm, which has the same offset I believe. And the lowest it...
  14. S

    OTHER Ku dish mount elevation angle

    Yeah, I realized the 85cm is the size of the dish, not the offset, lol. I did some more digging and found that the geosatpro 90cm appears to use this same mount and I think has a similar offset. I found those instructions online and the mount/scale options are much clearer. It looks like if I...
  15. S

    OTHER Ku dish mount elevation angle

    Hello all... I am taking my first stab at a Ku dish setup, I've purchased a 39" Electorica dish which actually appears to be more like 36" as I believe someone else had mentioned. It says the offset is 85cm. I'm in Hawaii, so I am doing a temporary setup to see what I can pull in before doing...
Top
Back