Search results for query: *

Dear All My understanding on satellite position is at each longitude there will be only one satellite, but when i referred LyngSat - Lyngemark Satellite i found Eurobird 1 Astra 2A Astra 2B Astra 2D Are all at 28.2 deg East. Similarly some other satellites are also there. Can...

Dear All I am using an ASTON CAM module, the CAM module stops descrambling after some time. Again the video is played when i remove and reinserted my CAM. Can any one have any idea why a descrambler in a CAM stops descrambling. Regards Mohanaprakash T

Hi I am having a SG2100 DiSEqC motor, in my set top box there is a option called recalculate position, which will recalculate all the stored position. sometimes this command is not working properly. I did the below tests, i stored following dish positions in location 1,2,3,4 respectively...

hi I am having a universal dual band LNB with LO values as 10.6 GHz and 9.75 GHz. I am using sun DTH network. It is having a downlink at 11610 MHz . If i tune my box to below value it's locking Downlink 11610 Lo1 9.75 Lo2 0 Xover 0 22KHz OFF Lband 1860 MHz If I use my high band then...

Hi I am having a DIGIWAVE GD-41A DiSEqC 4x1 switch, i am using the following DiSEqC message to select the switch position, for the below message switch is working properly. Position Message 1 e0 10 38 c0 2 e0 10 38 c4 3 e0 10 38 c8 4...

Hi I am having SG2100 DiSEqC motor, When i select Horizontal polarization in my box i am getting 18.4V in the output. When i try to move my motor it starts moving and stops immediately. I tested the voltage at that time and i found my output voltage is going to 0v and it is coming back to...

Hi I want to know whether any DiSEqC command is available to read the present dish position and direction. In DiSEqC 2.2 there is command "PosStat" - Read Positioner Status Register which is returning only the following items Bit Number Positioner Function .7 Movement command has been...

Hi DiSEqC 1.2 supports , switch position selection from 16 different inputs (SMATV) I wan't know whether any 16x1 switch is available in market, if it is available means can some tell the model name Regards Mohanaprakash

Hi I am working in a STB product, where we are using LNB H23 as LNB controller. LNB Register Details PCL TTX TEN LLC VSEL EN ITEST AUX 0 1 0 0 0 1 0...

Hi I am using SG2100 motor for dish movement, when i give the command E0 31 6E 01 40 it move properly to 20 deg East but when i give E0 31 6E FE C0 it not moving to 20 deg West. If i give any command to move in west it is not moving, some time for that also it is moving in east direction...

We are working on a DiSEqC implementation, where we are using STi7109 as a master in the board we are also having a LNB controller (LNBH23) . Bus supply is fed through LNBH23.In DiSEqC bus specification it is given that command 0X21 (Set VR)will set the LNB in vertical polarisation. My doubt is...

We are working on a DiSEqC implementation, where we are using STi7109 as a master, in the board also we are having a LNB controller (LNBH23) . Bus supply is fed through LNBH23.In DiSEqC bus specification it is given that command 0X21 (Set VR)will set the LNB in vertical polarisation. My doubt...