Search results for query: *

I appreciate your efforts trying the internal LNBF switch at your coax range. I have a motorized 42" with a quad invicom I use for Ku but thought I might test Ku on the 10'. If every thing works as planed, I have a 18" motor with a manual positioner that I'm adapting to use with the BUD for...

I was wanting to avoid two cable runs with switching inside the house. OK, I see what you are going to do. Yes I may need to do the same if I can't switch at the LNBF. I would need two runs of coax and larger conduit.;) Thank you much for your help.

Great, so polarization switching at that length is no problem for you using the RG-6 DC voltage.:) Have you ever tested the internal DiSEqC switch of the DMX741 using just one RG-6 cable for C/Ku successfully? I'm asking as this is the LNBF I have chosen to use too.

Yes, I also was thinking about future upgrade cables/repairs using conduit. On your successful long cable run, are you using a pollinator servo LNB or a single cable LNBF? Thanks, Dishman Dan.

Hi jimdandyvi, The cable will be flooded burial, have adjustable dies to RG-11 in my snap/seal tool, but have you any experience with the DC at long cable runs? I can not find a 300' piece of this type of cable to purchase and temporary hook up and try but CCS. Thanks.

I live in a forest and that is as close as I can get. New setup (wife approved) 10' unimesh dish, C/Ku Lnbf, DiSEqC positioner, with my CW LMC-4000HD. The DVB-S2 tuner runs 400 mA and I'm worried about the internal DiSEqC switch and DC at the LNBs. I'm thinking by the specs of the RG-11...

Thanks for the info, I am trying to decide weather to purchase a Geniatech Digistar 2HD or a Technotrend DVB-S2 to test a CaptiveWorks LMC-4000HD. These are the only 2 cards that support beta testing.

Thanks for the info. I am beta testing a CaptiveWorks LMC-4000HD and Technotrend S2-1600 is one of the cards test supported.

I was going to suggest you check out the Captiveworks LMC-4000HD. It is a great all in one Linux based PC box that will never be outdated, and at a good price at GOsatilite. But I didn't like the response you received so maby I will look else where for my FTA needs. Even if they couldn't help...

He must of found out that at that boot %, it is usually detection HDD stop.

Look at CaptiveWorks LMC4K it works great, an all internal PC that never grows old.

I didn't think you could us a tracker like that on a duplex TP. Turns it from 2 watt to 0 watt from voltage flash, not reversible.

I'm new to FTA, that said I think most FTAers will soon, or wish to become bird watchers. Their is many stations availble to a single motorized dish. I started that way at the first, and purchased a lower quality motor (on buget) big mistake. I didn't know till later the difference. The HH...

That was a simple fix. Didn't think of that! Will do if dish is off a lot. The weather is to be nice the weekend, I'm ready to install it. Thanks abunch!

I think you are right, leave alone while the beam is centered. When the weather is better I will add the QPH-031 and see if I can get any kind of signal on the ground. I guess If I use a highpower sat stationary, it will allow for tweeking and if dish works I'll add the SG2100 and finish the...

Hello, Newbe to FTA. Setting up first system. Found a old 3 angles offset dish 32”VX30”H, on a budget. Dish lays flat but arm is to left. Clamped a D-cell Maglite in 40mm lnb mount and moved the narrowed beam to center, no problem. Later I noticed my other dishes DTV & WildBlue, had the lnb...