Search results for query: *

It's happening on all the receivers (8 of them). I'm going to try and swap it out. So you said you can't use flex port 2? It won't work? Thanks for your help!

I'm picking up the 95 satellite. I took the LNB for the 101 out (not needed). My system has been working perfectly fine for the last 1.5 years. The mast is perfectly plumb and nothing can take it down. No tree blocking at all. Perfect line of site (it's on the very top of my roof.) I'm getting...

Also is it common that these switches fail after 1 1/2 years?

I did that. I hooked up the line that goes into the flex port and had a solid 100% on the birdog. I know it's not the coax line since I changed the coax cable. When I hooked the line back into the switch, I'll be able to watch the international channels again, but eventually it will freeze and...

Is it possible I could use the other port? (Flex Port 2) Would it work? Trying to eliminate all the possiblities

I have been losing signal from this satellite, My receiver will read (Acquiring Satellite Signal) when tuned to the international channels. Since DTV is charging to come out and fix it, I am attempting to fix it my self. I first checked to see if the Dish is in alignment which it was, since I...

Just installed my FTA MOTOR DISH!!!!!! and it works on the 22khz side!!! anyone have a satellite list for the Sonicview Elite 360? I am missing some satellites like 113 Satmex 6....

Hmmm...good to know...what about on the 22khz side? Will it still work?

Will a 22khz Encoda Switch work before the motor? Will I still be able to move the motor from the receiver? If not, how about I move the motor into the 0khz side? I don't want to run an extra coax cable into the house....I have too many cables :D Also, how about after the motor? Can I run...

I C&P from dishpointer.com :)

Thanks for the helps guys....I will try this later and let you know how it goes...

I just bought a HH90 motor with a Fortec 36" and an Invacom QPH-031....I was wondering what my true south satellite would be...... Latitude: 34.0989° Longitude: -118.1650° Motor Latitude: 34.1° Declination Angle: 5.5° Dish Elevation: 39° Elevation: 50.4° Azimuth (true): 180.0° Azimuth...

How long are your screws? I bought 8/32 - 2.5" Length screws......i couldn't get the 95 LNB to be tight...maybe its possible to use 2 of those Eagle Linear LNBS? since they are smaller in in thickness...

how did you get the 95 LNB to bolt down? I tried doing this earlier....and I would not get a signal unless it is bolted down tight....

DTV International Dish Is it possible to switch out the 101 Circular LNB to a Linear LNB to receive AMC 4 101 programming? Thanks

Is it possible to replace the 95 LNB on the DTV Dish with a Dual Linear LNB? Something like this Link ? One port will go to the 6x8 Zinwell switch for DTV and the other will go to a FTA box? is this possible?

Thanks for the all the help...

Ok, I mounted the dish about a foot away from my original location and I have found 95 within couple of seconds with 70 quality.....funny how just a foot can cause the signal to be from 20 to 70......i guess it was really the tree...

Nobody knows?:(

anyone? :confused:

Ok, I got a friend that has a birdog and I'm borrowing it. When I select (KH GALAXY-3C 95) it will show Signal of 178 and Quality 0....and it says "FOUND" on it....whatever I do, I can't get a quality..... I tried pointing it at Galaxy 19 IA5 97...and got a quality of 70........ I have no idea...

I already have programming with DTV and have the slimline AU9 as my main dish.....

What do you mean by auto configure? I went into the satellite setup and did the configurations there....it asked me what dish I had, then asked if 95 was installed....etc...

I am using a Zinwell 6x8 Switch.....the 95 is hooked up to Flexport 1.....and I have a H21 receiver

The cables are good. I made new ones just in case......the LNB is pushed all the way in and is in the groove.... The best signal I get seems to be 45 on TP1....no matter how i tweak it....