Search results for query: *

Looks good glad the lifter worked for you on the higher ones like that i would set up a 24 ft extension ladder behind the dish tie it to pole if it was not near a roof to stand on the problem always was getting the lifter up ladder and bolted around pole push it up mount so it was high enough to...

I just got a new computer was setting it up Friday night did not see your post or get your pm until sat afternoon i sent you my phone numbers Sat afternoon when i finally got email accounts set up and got your messsage

When I used my lifter especially that high be careful as you don't want dish to tip over make sure you have hooked as high on mount as possible. You put lifter on poll as high as possible behind dish but you can swing dish and lifter around on pole to take off any direction needed. I would...

I've had some requests for more info on my dish lifter had it made not my design years ago to assist me in installing and removing cband dishes I had the choice between steel or aluminum should have gotten aluminum as it is fairly heavy you bolt it around poll just below where the dish is going...

Here is the lifter a welder made it for me years ago was a lot easier to lift back then but would fit multiple pole sizes and was able to lift dish mostly by myself with someone to steady it and help me guide it on pole same thing in reverse when removing it I could let go of it and it would...

One of my old customers wants to remove his 10 ft dish if anyone is near Regina, Sask, Canada it can be yours for the taking it's a Star Trac I believe. I have not seen it for years but he says mover still works von wiese not sure what receiver but it is not a 4dtv think it is an older GI. I do...

You know if everyone sent in just a small amount of money 5 ,10,15 or 20 dollars would go along way to help finance project. Its not hard they do except paypal, that's just a couple coffees for this week. And thanks again guys looking forward to release just like everyone.

Ok good to know I am getting ( lost Sat signal) I thought I had a bad LNB I changed all my connectors at LNB was looking to replace my 75E LNB which I don't have a spare I was going to put a 60E on until Star Choice replaced my 75E but if it is a software bug will wait for new update soon...

I had the same problem with Skype it used to last 2 days before I had to charge it after updating Skype it had to be charged every day so I turned off Skype until I want to use it now battery back to 2 days before needing charge

I use websam and don't have US credit card just US address associated with my 4dtv I even asked them when I started subscribing if they had any problems with Canadians he said why would I .

I took 5 Andrews 10 footers down for local cable company in the late 90's for 400.00 each they kept them I removed and delivered them to the cable company from different locations rented crane for the morning went around lifted them off and hauled them back to them took about 5 hours then went...

I have 6 channels I send around my house a 3 channel modulator and a 2 channel modulator and a single channel modulator plus 3 over the air channels I have 6 tv's and all you do is tune to one of the 6 channels or over the air channels and you have a picture works great now I am looking into...

Here is a picture of mine as I was saying I found when the mount is directly behind dish when you get over to the far east the arm is pulling straight back against the pivot point which can sometimes cause the motor to give you an error also as tvropro says make sure your physical limit is...

Found a picture of my father in-laws dish which I put up you can see what I am talking about on his dish just a bar fairly thick coming off the back of the dish at a right angle then mount your arm on the end of the new bar.

I think you might have a problem with where the arm is mounted on the dish because it is right behind dish when it gets over to the east it is very hard to get it to stop on a satellite, I put a bar at a right angle to the mount to mount the arm on which gives you a lot more control on the east...

Since you are putting in the pole tomorrow make sure you have a clear shot to the south and that the pole is plum if it is not you can have tracking problem. If you go to the search you can find a lot of info on how to set up a cband dish

Got mine last night put it in today so far so good have to wait for receiver update before I can try recording seems they have a bug in fist draft current version is 00.10 waiting for update to 00.13 overnight receiver is small compared to 530 picture looks great. Receiver has a small lag when...

I agree I used to use my driveway as it was fairly level I would put something about the depth of the dish in the center put the panels around and put bolts and nuts on loosely then making sure panels where aligned and flush, I would start at the bottom row snugging up nuts and bolts going...

I found when dish is moving out or arm is extending it is more accurate as all the slack is out of dish from weight of dish but when retracting the arm on the east side where the weight of the dish is not on it you are pulling it back, it may stop a few counts out to fix this go one Sat past...

I am using a Atlas universal that the cable company gave me in the back of the book they also have Satellite codes that will work the 4dtv the code I use is 0869 as long as you have not changed the 4dtv from factory code (0) it should work . This will also work for Voom, Starchoice, Radio...

Starchoice or Shaw remotes work on 4dtv's as I had to reprogram my 4dtv so as not to change channels on my Starchoice. You can even program motorola's cable tv remote to work a 4dtv just need code book.

Anyone looking for a 10 foot mesh dish I have one to get rid of (free) I live in Sask Canada not sure of the make but it is a ku compatible 4 piece been sitting in my shed for years now pm me if interested.

Hello everyone I've been playing with Satellite since the late 70's I am a retired firefighter who now works part time for the local cable company on a contract basis (don't have cable myself) my hobbies are Satellite and computers I installed c-band systems back in the 80's and 90's. I am now...