Search results for query: *

For a whole month was plagued with seemingly random signal outages on my BUD. Swapped RX, LNB, DiSEqC switches, even the positioner (ASC-1). It started with a drop in SNR after about one hour on the same xponder. Eventually, I couldn't maintain lock for more than ten minutes. The quick fix...

Antenna is in an open field, so it's clear from 139W back to 11W before a ridgeline gets in the way. Have to swap actuator positions from West to East to see anything below 27W. An H-H motor is a project on my list. Thanks for the bookmarks... I'll try these out. The second full scalar...

Well, I've heard the best preamps money can buy are made by Stihl and Husquevarna ....

My Sunday project was to add another feed to my 10-foot Unimesh, for circular polarization reception. The recipe called for an old scalar ring and single-band polarotor, LNB, junk metal brackets, and a cheesy plastic cutting board. It was a success. Quick look at the photos and diagram...

Brian -- thanks for clearing that up. Realized that was what was going on as well after a few more rounds with the thing. Oh -- and I'm happy to report that the Vu+ and ASC1 play nicely together! ;) I've seen the Zeros, but was intrigued by Uno's dual tuner. And I've seen threads...

As it would happen, I finally took.delibery of another Enigma box just this month. Exec summary of first impressions: Vu+ Uno 4KSE is a sleek, flexible, fast box in terms of boot and manual scan. Learning curve on programming and western longitude operating idiosyncrasies is marginal for a an...

Sounds like feed setup ain't optimal (like Ti said) to me.... Lobes may be pulling some solar noise. Noon PDT at 99w sounds reasonable. If the freeze goes away for a few days, this theory looks more accurate.

Flux like that is typically terrestrial born interference in my experience. WVMAN, the ABC issue could be that air conditioning around you is cycling on and off in prime time, vs during midday it's just on. Arc in those contactors, or from dirty brushes in the condenser fans can make...

Following up. Ran new Cat6 STP dedicated to servo action 100% from ASC1 to servo. Pairs were doubled for each line (5VDC = WhBu/But, Pulse = WhOr/Or, Gnd = WhGn/Gn) to keep voltage drop in check over this long run. Super clean action now. Thanks Ti and EST for the the on this one.

I hear y'all on ragging me on the wire choice. ;). No prob. Here is some more detail... It is not quite so ugly as 100% cat. Leg 1 is about 15' (ASC1 TO BASEMENT TVSS JUNCT) .as described 1 run Cat6. LEG 2 is abt 225' (HOUSE TO ANT MAST). Here, motor hops off to a larger gauge -- direct...

Here's a fun one. Linkbox 9000iLocal Ti ASC1 250' of cable Uniden 10' w/ VonWiess linear mover Chapparal C/Ku servo-driven feed Worked great up until a few weeks ago. Started losing servos -- or apparently so -- polarity control would disappear. Swapped three of them. Then I took a pull...

France24 is my go-to, along with DW.

My CPII suffered a linkage failure a few weeks ago. Stuck with single band stuff the moment. I see eBay listing used Chapter CPIIs for about 150% the price of new ones from some broadcast vendors.... I think my replacement will be a new one.

Thanks for the write-up. I think the ASC1 is hard to beat. Mine went "blank screen" for a while if it had to move the 3m antenna more than about 20deg. Stop and wait, display would come back. Sometimes the LNB voltage would wink out in that '''blank" phase, too. Turns out, I had a bum...

I have found false images like that before. I scanned the arc with a spec an, noting positions with signals, then told the STB to go check them out. Turned out, along my Eastern limb, what I thought were low horizon birds were images of higher longitude birds. Its tough -- nigh near...

Right now, ASC1 is first in the line from STB and all is well. I started recording some 22kHz commands from the 9000, but haven't done the same with the "other" box for comparison. Will post results of that when I have them. Yes appears 9000 is "picky" with DiSEqC.

Thanks all ... Titanium - Thanks for the offer in the string reader. I'll let you know if it looks like that box will answer some burning questions. And, the ASC1 is a stellar box! @EST - awesome Arduino project! That one is on my build list now. Will certainly inspect with a DSO just to...

Update: LinkBox 9000i Local got a factory reset. I deleted all the sats in the factory list and started clean. Then, I manually entered into the 9000i the sat names, positions, and memory number as it is stored in the ASC1. I set the 9000 to do a multi-sat blind scan, also known as the...

Yeah, tried different memory spots to no avail. Number of other things, too, like completely deleting the sat from the list and starting from scratch. Same result. I confirmed my other EX box has no trouble with sat mems above 13. So will wipe the LB and start again. Film at 11.

Got a Linkbox 9000i Local tied to an ASC1. Works great up to satellite position 13. On Sat 14, ASC recalls position fine, but changing channel or selecting the sat from the LB channel menu fails. Says, "moving dish", ASC wakes up display, but doesn't change position. But under the Sat...