Search results for query: *

I would like some guidance with the procedures on how to get the sg2100 installed properly with ProgDVB. I installed the plugin and checked it in the program that it is there. I use the motor in MT but want to use ProgDVB. I am lost. I am not sure if I start at the disecq tab and then where to...

I have a nexus S and I scan channels and can only scan the H polarization. I only have a straight connect to the lnb. I put a mini disecq on it and I can only scan the V polarization. I think my voltage is not switching properly. Help oh and I am using MyTheatre 3.21 regged

I don't know why but MyTheatre don't seem to move my dish. I go to the positioning console and try to send to 0 or move in 100 increments but it never moves. I have a green light and I have tried resetting it. The SG2100 is new and I am using the current MyTheatre 3.21 but no luck. Help tks...

I don't know why but MyTheatre don't seem to move my dish. I go to the positioning console and try to send to 0 or move in 100 increments but it never moves. I have a green light and I have tried resetting it. The SG2100 is new and I am using the current MyTheatre 3.21 but no luck. Help tks...

Greyskies, Thanks for the info. Did you also get a standard ku lnb or are you using the universal one. My dish is on a 10 foot 2" rigid pipe. I is about 1 foot above the roofs edge. I get lots of signals but can't get them when checking them on the progdvb or mytheatre. Maybe I will have to...

so now instead of aiming for AMC 5 I should aim for telstar 5 ?

OK I am at my wits end. I move the dish just a little bit each time and when I get to the next strong signal on the sat meter I go in and scan all the sats in progfinder 2 and mytheatre and progdvb and the best I can get is a faint signal in progfinder 2. I have no problems with any hardware...

I have a 30 inch hotdish and a sg2100 motor and running nexus-s a ku lnb. I have set the dish to the furthest west sat I could get a signal at using my channel master sig meter. I went and turned on progdvb and went to scan transponders. I went through the entire region of sats in the...

I went to 185 because it seemed closer. So now do I need to set my levation back to AMC 5 or another sat ? I am only trying to be precise so that the far east and west sats will be easier to tweak

those two charts don't match each other. One says I am 183 and one is 185+

If that chart is correct then instead of my true south being at 183 like I thought for 80.17 Long it is more like 190 deg. ?

I have done several things required to get the sg2100 and hotdish aligned properly but I still need more help on some stuff that is making me uncertain if I am doing things right. I purchased a ku lnb to do the sat search and alignments with my sat meter but I have noticed that when I tap into...

I was only able to get to 60 clicks on my motor to the west for the last sat. I was getting a strong signal and I am using the kuLnb with digital ready lnb. I went and opened the diseqc1.2 and I wanted to store something but I notice I get no signal or quality

WOW lots to do. I will go on the roof and try it. If I get mad I will install my diseqc switch and get in front of the TV and vegg my brain on the two sats I have setup allready. Then I will try again tomorrow

hmmmm what utility would be good for that. I thought if I was to just use the diseqc 1.2 to move with the mouse or for steps or seconds I did not have to do that. I need help.

Well I am about at my wits end. I reinstalled progdvb and over wrote you progdvb and I still can't get the dish to turn by the motor. I get a green light and I get manual movement but nothing else. Every once in a while I see a red blink on the sg2100 once and then a rapid redd and then it goes...

I went ahead and uninstalled the prodvb I had and just coppied the one you sent. I started it but when I try to use the motor it don't move. Do I have to do a complete re install or something. Not sure about it.

I noticed after I sent the message. Thanks

Should I just import your ini file ?

Well I have progdvb allready loaded but I will see if the version is the same. Gonna try some of the ideas you suggested

hey no problem. I have seen two charts that read slightly different for my true south but they are only 1 or 2 deg off from each other. Right now I am trying to get the motor to work with my nexus-s and cascade is helping with that

OK I am off to work and I am looking forward to hearing from you. Thank you

I will accept anything you can off to help. What kind of changes do I have to make since we are at different locations in the country. I live in SE Florida. I am not sure if this matters. I still have a little bit of tweaking to do on the eastern sky of my dish rotation. I think most of the...

Very Interesting info. I appreciate it. I hope that I can translate it all since I am a bit new at working with this software. I had just got MyTheatre working but I did hear that progDvb was better for some. I will look it over and see if I can make sense of all of this.

Cascade, PSB says you are good with the MyTheatre prog. I can't seem to get the sg2100 to move and I do have power to it. Any help you can offer ? I am also using the Nexus-s