Search results for query: *

navy, i haven't opened the box yet. i was hoping someone could tell me if there is a seal on box, an intrusion switch on the box before i opened it and looked. sounds like you know...do they put tamper seals on the connectors of the drive?

i have an EHD. i was thinking i could swap old HDD into the New machine, then boot it up in new machine, and transfer all recordings to my Ehd. then swap HDDs back, and ship the bad one back, with its original HDD.

i know this is desperation type of thinking... 922 just died. tries to boot, but can't boot. keeps resetting. this was my 2nd 922, and i've only had it a couple months. i can't get to my recordings, since it won't boot. i've tried disconnecting everything and it will come up just long...

service tech came out and replaced everything but the box, and still had same symptoms. so, i got me a new 722, and everything is working fine. old 622 went bad. the strange thing is how the factory reset gave it completely different failures and sympoms.

i refuse to pay for someone to service a their box. for the cost of paying someone to come out, I can just quit and switch to Direct, Cable, or ATT.

i have the dish 1000 with the quad LnBs. not sure of the right terminology. i assume this is all the right setup, i haven't touched it since Dish installed it a year ago. been working fine until this week.

Well that didn't work. NO change in the situation. it appears i have bad hardware. One other thing i tried: i disconnected the DP Separator that goes into Sat 1 and Sat 2 inputs. connected single line directly to Sat 2, ran Check Switch, and the SAt 2 showed Good. (all runs today with spliter...

Did the factory Reset. It worked BUT....check switch shows 'reduced satellites' first time. saved those settings just to see if i could view, and YES, tv works. added local channels and they do not have program guide info, but they do work. External HDD does not recognize either. ran check...

one more tidbit. when i change to OTA channels, it does the same error flicker, only with different eror message 738 (lost off air signal.) i'm pretty sure this box is hosed. i just need to figure out a way to get Dish to send me a new one without costing me money.

just tried that with Dish Service...hit menu button during Sat acquisition. Check Switch went fine, all signals good. did a Program Guide Download, and then back to the same locked up Error loop. Here's the kicker: they wanted me to pay for someone to come out and take a look at it($50)...

OK, i think i have a similar error to everyone else L511 software error...but mine seems worse. i have software L512. don't know when it came thru. Last nite around 10:00 pm, it started flashing the 002 error (lost signal) back and forth about 3 times per second. In between Error flashes, i...

Yes, i did this in my house. beware, the splitter can degrade the picture quality. I have TV2 active to my bedroom and to my office. never need it in both at once.

carter, i tried what you are suggesting, and i could not get the reciever to see any of the OTA channels. Too many splitters, too much signal loss. i put a radio shack booster inline with the OTA input, and it worked. personally didn't like using that, so i just ran a separate cable from...

Before i unbox my SEageat Freeagent 250, and hook it up to my 622, any other Seagate owners out there that can advise me on possible bugs, or tricks i may need to know? i've read thru the threads, and it looks like I'm OK, but i'm afraid i missed something in 30 pages of searches. Will I be...

don't believe the website, it means nothing. i have called 6 times now. last called in November, and the guy said they knew nothing about my rebate, but he was going to add it to my account. I wait 2 billing cycles, still not there, so i call again. they tell me it will be on my next bill...

i am mostly in Single mode 99% of the time, so i'd like to try to make this 6.0 remote work. getting a 6.3 remote would make it work in any mode? (uhf on both Tv1 and tv2)?

on my vip622, i want to have a UHF remote in both living room and bedroom. current setup has IR only remote in living room. i want to move the 622 box so that its out of sight. i bought a ir/uhf remote from someone here, 6.0 remote. can you point me in the right direction on how to program...

same problem with my 622. if i change channels, sometimes it goes away.

i have been waiting since August. 3 calles to CSR, and the last one told me it'll be on my next bill because he added it. we'll see. this is both the 10$ per month rebate and the 100$ equipment rebate.

tsutton, i tried a similar setup, not using a dp44 switch. tried combining the backfeed signal, satellite, and OTA signal all on a single cable. basically, i had too much signal loss with diplexers and splitters, and could not get my OTA to work without adding an inline amplifier. i ended up...

i'm having the same problem...are we positive this is the way it is? i had an 811, and my channel guide worked perfectly for OTA channels, w/o local channel subscription. Now my 622 does not work. no one has been able to make it work at all?

Can someone quickly answer these questions on splitters and frequencies...i want to make sure the hardware i'm using is not causing my problems. forgive my newbie-ness. -first, what frequency does satellite signal use and what freq does OTA HD programming use? and modulated TV2 output...

thanks for the advice Jeff. So you're saying my third (right) diagram "should" work?

OSU, much appreciate the input. your diagram is not quite what i have. my antenna is on the dish has a built in diplexer, so the antenna and satellite signal are combined on the one coax coming in from the dish. So i didn't want to make my original post too long, but i tried adding a radio...

OK guys, forgive me, i've read every thread i can find, and i'm just too new to figure this out on my own. Hopefully someone on this site can see the error in my setup. Terk tv-44 antenna clipped to the dish. Dish 1000, just installed. 622 in dual mode in the living room television in bedroom...