Social Feed

Almighty1 said:

JohnGalt1234 - So you basically have 2 Hopper 3's. The CasinoH3 is the one that is Hopper 3 only while Master Bedroom is a Hopper 3 with Hopper Plus setup.
Master Bedroom uses Android TV (ATV) software so the DISH part is actually a app and will behave differently as you can probably tell the Guide's are different on the Master Bedroom which will resemble the same guide used on other ATV devices such as the Joey 4 and Wireless Joey 4. If I am correct, the CasinoH3 is the one with the problem since you did say the one dated 09/05/2026 is the naughty one while 08/15/2026 named Master Bedroom is the nice one. Usually I would expect the CasinoH3 to be the one without the problem because it's Hopper 3 only and Master Bedroom would be the one with problems because it has the Hopper Plus involved. That is why they behave differently because CasinoH3 is running the native Hopper 3 software while Master Bedroom is running the Android TV software and also it runs a app called DISH known as package com.dish.atv.launcher, the version for mines is P15403 2026100917 so it's probably the same version as the Hopper Plus software version with the date of October 9, 2026, not sure what the 17 means except maybe revision 17?

This explains it better than I can. Sorry, had to take all the ads out.

View attachment 194857

Click to expand...

JohnGalt1234 said:

As I understand it, the android is just the display signal from the hopper+. I can disconnect the H+ and plug the hdmi directly into the master hopper3.

Click to expand...

navychop said:

It'll only see two EHDs at a time.

Click to expand...

bookworm370 said:

Yes, I have only two online at a time.
One comes online; the other consistently won't. Also, when I connect the EHD, the USB Detected status light on the EHD itself changes from Red to Green. But the Hopper (713) does not start the EHD read process. The light changes to indicate that the EHD has detected a valid USB cable, but the Hopper does not recognize it.

Click to expand...

Almighty1 said:

It is not just a display signal as explained above. When you have the Hopper+ connected, it uses Android TV for pretty much everything except for the satellite signal which is why it uses the DISH app for the standard Hopper 3 functions. But that should not matter because in your case, CasinoH3 is the Hopper 3 with the EHD which is what you call the naughty one based on the dates you mentioned and Master Bedroom which has the Hopper Plus connected to the Hopper 3 that does not have the problem. So one way to test the theory is disconnect the Hopper Plus from that Hopper 3 and then use the EHD's connected to CasinoH3 currently to see if the same issue exists. That way you will know if the problem is there without a Hopper Plus connected or if CasinoH3 is just a bad hopper to begin with.

Normally when you disconnect the Hopper Plus, it will be 30 minutes or more before you can use the Hopper 3 again.

What you want to do is:
hold the POWER button in, not the red reset button, for about 45 seconds or so while disconnecting the power to the Plus and moving the HDMI cable and it will reboot to the normal Hopper only immediately.

Click to expand...

naptime said:

I'm getting fabulous picture on Ch. 148 4k, but zero audio with H713. This is with a recorded show (Notre Dame game). Anyone else have this? Audio is fine on every other channel.

Click to expand...

jsmit86 said:

It's a known issue.
For a temporary fix, go into the menu, Audio, and turn Dolby Audio "OFF". You will have PCM stereo audio.

I was able to give the tech ops team some data logs so they could diagnose the problem, and they rolled me back to H708 temporarily. It fixed that issue.

They let me know that they understand what caused the issue, and it will be fixed within a few weeks in a new update.

Click to expand...

Almighty1 said:

it will likely fix the OTA Single Tuner

Click to expand...

Almighty1 said:

it will likely fix the OTA Single Tuner

Click to expand...

rvvaquero said:

That's a lot of information to ingest. However, I don't have the Hopper Plus and my 54 remote is doing crazy things to the Hopper 3. Several times each evening when I press the skip forward button several times to advance through a commercial, it switches the receiver either onto live TV or into suspension. Other buttons will also cause this randomly, I haven't established any patterns I can describe. I use "recall" to go back to my recorded program in progress.

Needless to say, something in the newer Hopper 3 softwares has caused the remote functioning to ......................malfunction. Evidently, it applies to third party remotes as well as DISH's own remotes.

Click to expand...