Social Feed

vvovv

Last reply Jun 5, 2009 · posted in DIRECTV General Forum

installing a slimline

Going to be installing one next weekend.
1.Do I aim for 101 I assume the center LNB gets 99/101/103
2. Can I use a old SD receiver to set up
3. Can I use a diplexers so I still can receive My OTA

Thanks all

13 Replies · 2146 views

Load Replies (13) Reply Legacy View

jkr25nlpaz

Jun 3, 2009

ok here's the deal ... i am an installer, installing a slimline vs. and old KaKu dish is cake. whether you have a standard 100 dollar sat. meter or a bird dog (expensive, unless you install). don't expect to get an HD picture if you're trying to shoot in your dish with the beep from the receiver, not gonna happen. Installing on a SD receiver will work just fine, but again, don't expect to get an HD picture later. Also, mount must be sturdy and level (not close, level !) you'll notice on the back of the dish mount there are dials, these are for fine tuning so you can pick up your other HD's 99, 101w, 103 . . . if you can't fine tune your HD will suffer. Ok, diplexers work great if you're not using HD or HD Locals, when you use a diplexer you limit the ammount of power your receiver is sending to specific LNB's, when this happens you lose transponders ( when you pull up signal meter on receiver you get a grid of numbers that show your signal, each of these is a transponder, if you lose one, you lose channels). So NO diplexers with slim line or other KaKu, run a separate line to your off-air.

raoul5788

Jun 3, 2009

jkr25nlpaz said:
ok here's the deal ... i am an installer, installing a slimline vs. and old KaKu dish is cake. whether you have a standard 100 dollar sat. meter or a bird dog (expensive, unless you install). don't expect to get an HD picture if you're trying to shoot in your dish with the beep from the receiver, not gonna happen. Installing on a SD receiver will work just fine, but again, don't expect to get an HD picture later. Also, mount must be sturdy and level (not close, level !) you'll notice on the back of the dish mount there are dials, these are for fine tuning so you can pick up your other HD's 99, 101w, 103 . . . if you can't fine tune your HD will suffer. Ok, diplexers work great if you're not using HD or HD Locals, when you use a diplexer you limit the ammount of power your receiver is sending to specific LNB's, when this happens you lose transponders ( when you pull up signal meter on receiver you get a grid of numbers that show your signal, each of these is a transponder, if you lose one, you lose channels). So NO diplexers with slim line or other KaKu, run a separate line to your off-air.

Sorry to nit pick here, but if you set the mast to level you will never get a picture. It must be set to plumb.

jkr25nlpaz

Jun 4, 2009

raoul5788 said:
Sorry to nit pick here, but if you set the mast to level you will never get a picture. It must be set to plumb.

hey, i don't mean to nit pick ... but if anybody set there mast to level, they probably can't even operate their television let alone install a dish, however when i am to mount the mast for my dish, i'm probably going to use a tool called a level, and when you use a level it gives you a bubble of water that you would level on a horizontal plane, from front to back, as well as side to side. When doing so you would then be left with a mounted mast that is "exactly, precisely and directly vertical." or in other words, Plumb. However, thanks for the info. I'll make sure I correct the thousands of customers i've left without service.

raoul5788

Jun 4, 2009

jkr25nlpaz said:
hey, i don't mean to nit pick ... but if anybody set there mast to level, they probably can't even operate their television let alone install a dish, however when i am to mount the mast for my dish, i'm probably going to use a tool called a level, and when you use a level it gives you a bubble of water that you would level on a horizontal plane, from front to back, as well as side to side. When doing so you would then be left with a mounted mast that is "exactly, precisely and directly vertical." or in other words, Plumb. However, thanks for the info. I'll make sure I correct the thousands of customers i've left without service.

I didn't mean that you don't know how or haven't been properly plumbing the masts that you install. However, using the correct terminology IS important to make sure no one is confused. Although I doubt many, if any, thought you were really leveling the mast, I have, for instance, read a lot of posters confusing a fascia and a rake board. Fascias hold gutters, rakes go along the slanted edge of a roof. Mixing them up can make things very confusing. That's all I am saying.

uncrules

Jun 4, 2009

I recently learned that even if you have everything installed correctly and have the alignment just perfect you can still have signal level issues.

I had a slimline dish installed before D10 and D11 were launched so at the time of installation the tech couldn't check their signal levels. Once those satellites launched I was only getting readings on 99 and 103 in the 30s to low 40s range which made my HD channels more likely to rain fade issues than normal. However, I was always getting high 80s to 90s for 101, 110 and 119.

I have the protection plan and have tried several times to get D* to send someone to realign my dish. Well recently I finally was able to get D* to send someone out. The first thing the tech did was put up a new dish (but still a slimline) and he was able to get the readings on 99 and 103 to about the 50s range. He tried many times to improve it more but with no luck. Then a supervisor came out and after a while longer they finally got the signals on 99 and 103 into the mid 90s.

I asked what they did to get the readings that high and they said that in both the original dish and the one the first tech put up when he got there, there were bumps in the dish. So they had to put up yet another dish and then it was all good.

My original dish had a bump that they could see and the 2nd one had a bump that could be felt but not seen.

Davedirectv

Jun 5, 2009

Sounds like you got into a bad lot of dishes, I've heard of some techs taking the slimline holding it from behind, putting their knee in the middle of it and bending it outwards and getting a better signal, and vice versa. I'm fairly certain this isn't D* approved but it worked.

Quikest and cheapest producers, that's the way!

View all replies (13)

TWiT Tech Podcast Network

7 minutes ago · posted in TWiT Tech Podcast Network

Project Helix Price Rumor: Could the Next Xbox Cost $1,800? #shorts

Time for another AWESOME video from the TWIT Network!

View: https://www.youtube.com/shorts/x3Zbzo-tk-s

Direct YouTube Link - Project Helix Price Rumor: Could the Next Xbox Cost $1,800? #shorts
TWIT's Website
TWIT Live Feed

0 Replies · 1 views

Replies Reply Legacy View

Scott Greczkowski

Staff member HERE TO HELP YOU! Cutting Edge

Last reply 35 minutes ago · posted in The Chit Chat Club

Song Name Game Part 3!

Sometimes a thread gets so many posts in it that is can cause issues for the server so that why today we introduce The Song Name Game Part 3!

So let the game continue!

The last song was added by Bobby who posted...

One Meat Ball - Andrews Sisters

CONTINUE ON AND HAVE FUN! WELCOME HOME TO SATELLITEGUYS.US!

Here are the original rules for the game as posted by WebbyDude back in 2006. http://www.satelliteguys.us/threads/68645-Song-Name-Game

Just name a song title and the band who performed it. The next person does the same thing, but needs to list a song title or band name which includes a word from the previous entry. Pick songs from any genre.

Example:

Long Live Rock and Roll -- Rainbow

Rainbow in the Dark -- Dio

Another example:

Ride the Lightning -- Metallica

Lightning Strikes -- Ozzy Osbourne

Get it?

An additional note: we all know that song titles, sometimes, use profane words. Because this is a family friendly website it is advised that you clean up that title up a bit. This is accomplished by using something like sh!t instead of the real word. Thanks....

68565 Replies · 2675538 views

Load Replies (68565) Reply Legacy View

Reactions: c-spand

dishstaller

Yesterday at 11:42 AM

Little Miss Dangerous - Ted Nugent

RaiderPower

Yesterday at 1:24 PM

Little Miss Can't Be Wrong - Spin Doctors

Reactions: FTA4PA

sdfntx

Yesterday at 3:01 PM

Jump Down, Spin Around - Harry Belafonte

Reactions: Bobby

long_time_Dish

Yesterday at 4:27 PM

Stop Draggin' My Heart Around - Tom Petty and Stevie Nicks

Reactions: FTA4PA, gms49ers and dishstaller

hwkn

35 minutes ago

This Old HEART Of Mine(Is Weak For You)-The Isley Brothers

View all replies (68565)

iJustine

Last reply 41 minutes ago · posted in iJustine

iPhone Duo Crease?

Time for another AWESOME video from iJustine!

View: https://www.youtube.com/shorts/YxfvCOQv5uE

Direct YouTube Link - iPhone Duo Crease?
The official iJustine Website's Website
Buy her book!

1 Replies · 7 views

Load Replies (1) Reply Legacy View

telstar_1

41 minutes ago

It's not even where it folds!

iJustine

Today at 2:12 AM · posted in iJustine

Reading on the iPhone Duo!

Time for another AWESOME video from iJustine!

View: https://www.youtube.com/shorts/2KkkNffbY40

Direct YouTube Link - Reading on the iPhone Duo!
The official iJustine Website's Website
Buy her book!

0 Replies · 4 views

Replies Reply Legacy View

iJustine

Today at 2:12 AM · posted in iJustine

Playing Xbox on the iPhone Duo!

Time for another AWESOME video from iJustine!

View: https://www.youtube.com/shorts/6t2FDCK5y40

Direct YouTube Link - Playing Xbox on the iPhone Duo!
The official iJustine Website's Website
Buy her book!

0 Replies · 5 views

Replies Reply Legacy View

iJustine

Today at 2:12 AM · posted in iJustine

iPhone Duo Fold Animation

Time for another AWESOME video from iJustine!

View: https://www.youtube.com/shorts/_9uczoPSEaI

Direct YouTube Link - iPhone Duo Fold Animation
The official iJustine Website's Website
Buy her book!

0 Replies · 5 views

Replies Reply Legacy View

SuperDish_Fan23

Last reply Today at 12:04 AM · posted in DISH Network Support Forum

Its crazy how the ViP922 is so rare for no reason.

Why are ViP922s So rare? like its crazy how ebay has none, i checked everywhere, also, i got a ViP222k now, which is actually activated!

20 Replies · 493 views

Load Replies (20) Reply Legacy View

Strega

Yesterday at 2:34 PM

That's not really unusual. Cable companies like to the provide the box too. The phone company provided the phones in until the government forced them to allow third-party phones.

Reactions: charlesrshell

Almighty1

Yesterday at 7:02 PM

Strega said:
That's not really unusual. Cable companies like to the provide the box too. The phone company provided the phones in until the government forced them to allow third-party phones.

Yes, the Western Electric phones that says "Bell System Property, NOT FOR SALE, Western Electric".

Reactions: AZ., Bobby and charlesrshell

AZ.

Yesterday at 9:10 PM

Almighty1 said:
Yes, the Western Electric phones that says "Bell System Property, NOT FOR SALE, Western Electric".

someone is showing their age

Reactions: Almighty1 and charlesrshell

Almighty1

Yesterday at 9:38 PM

AZ. said:
someone is showing their age

LOL. It depends if the person saw it during the years when they were actually still available which is 1968 to 1983 meaning the person could be 43-58 years old or they can even be a few years old if they learned to read and write at a young age and actually saw a telephone with that label somewhere recently just like even here in San Francisco, payphone still exist physically in public places but whether they can be used or not is a different issue. It still looks like this even today:

Reactions: charlesrshell

dishstaller

Yesterday at 10:03 PM

I opened my Radio Shack in Sept 1984 and right about that time they did the whole deregulation thing with the phone companies. I bought TONS of those phones that had been refurbished with a new outer shell. You could throw one of those out of a 3 story high window and it would still work.
That was an interesting time in history. I would have older customers come in and ask about phones.....they were terrified that they were going to get into trouble hooking up a second phone without the phone company knowing about it. One of the funniest episodes of WKRP was the one where Johnny thought the cops were showing up because they had an unregistered phone. I guess younger folks can't conceive of a time when you were limited to the number of phones you could have in your house....and limited to the length of the cord

Reactions: navychop and charlesrshell

navychop

Yesterday at 11:01 PM

AZ. said:
someone is showing their age

You should hear his stories about when rocks were soft and pterodactyls were the new kid on the block!

Reactions: Foxbat, charlesrshell and Bobby

dishstaller

Today at 12:04 AM

dishstaller said:
One of the funniest episodes of WKRP was the one where Johnny thought the cops were showing up because they had an unregistered phone.

View: https://www.youtube.com/watch?v=CA0yZ1nrm6M&pp=ygUPd2tycCBwaG9uZSBjb3Bz

View all replies (20)

dishstaller

Pub Member / Supporter Lifetime Supporter

Last reply Today at 12:02 AM · posted in The Chit Chat Club

Country singer John Anderson died today

He was 71 yrs old. One of my favorite songs is Seminole Wind....the violin is killer.

View: https://www.youtube.com/watch?v=W8sh9P3X33w

5 Replies · 43 views

Load Replies (5) Reply Legacy View

Reactions: navychop and comfortably_numb

FTA4PA

Yesterday at 10:53 PM

Rest In Peace

Reactions: dishstaller

mikew

Yesterday at 11:01 PM

I Wish I Could Have Been There is an amazing song. Rest in peace Mr Anderson.

Reactions: dishstaller

Bobby

Yesterday at 11:03 PM

Rest in peace.

Reactions: dishstaller

comfortably_numb

Yesterday at 11:04 PM

Hope you're out there Swingin', John.

Reactions: dishstaller

dishstaller

Today at 12:02 AM

mikew said:
I Wish I Could Have Been There is an amazing song.

That's one of those songs that hits a little too close to home for me. I like the song but just can't listen to it. It's kinda like that song "Daddy never was the Cadillac kind".....reminds me too much of my Grandfather who died Feb 18, 1995.

niembre

Last reply Yesterday at 11:21 PM · posted in DISH Network Support Forum

OTA no working after Update

My OTA is not working anymore. This started after the latest update. I have the OTA dongle with a OTA antenna that I've been using for years. My hopper does not recognize the dongle anymore and when I go to the OTA setting, it has a screen that says to plug a dongle into the USB. I tried unplugging and plugging back, in the same usb port and other ports. The Hopper does not recognize it. Anyone have same issue?

201 Replies · 5105 views

Load Replies (201) Reply Legacy View

Reactions: charlesrshell

Scott Greczkowski

Sep 24, 2026

Did you people having this issue contact Brittany yet? Shes trying to keep track of things and it would be good for you to contact her as maybe she can get this somewhere and get fixed.

Now while unofficial, I am hearing this issue wasn't caused by DISH's software team, but was caused by a chipset driver update that seemes to have hosed some older USB devices. If this is indeed the case I can see why DISH didn't know and why they are slow in fixing it as they need the chipset company to fix its drivers and release them to DISH so they can be pushed out to all.

DISH does not hate you guys nor do they want you to buy new USB dongles. I am rather sure they didn't even know this was an issue until they saw it posted.

Again contact Brittany if you are having this issue, so she has your info and hopefully she can do something for you to keep you happy.

Reactions: Foxbat, Briant73, pamajestic and 3 others

bookworm370

Sep 25, 2026

Scott Greczkowski said:
Did you people having this issue contact Brittany yet? Shes trying to keep track of things and it would be good for you to contact her as maybe she can get this somewhere and get fixed.

Now while unofficial, I am hearing this issue wasn't caused by DISH's software team, but was caused by a chipset driver update that seemes to have hosed some older USB devices. If this is indeed the case I can see why DISH didn't know and why they are slow in fixing it as they need the chipset company to fix its drivers and release them to DISH so they can be pushed out to all.

DISH does not hate you guys nor do they want you to buy new USB dongles. I am rather sure they didn't even know this was an issue until they saw it posted.

Again contact Brittany if you are having this issue, so she has your info and hopefully she can do something for you to keep you happy.

Thanks, but until they do, can't Dish just revert to the old driver that worked? Then test the new driver when delivered,d before pushing it again.

But then what does an old CIO know! I've only reamed quite a few buttholes from my people that didn't do that!

Reactions: ppappas, Almighty1 and charlesrshell

slow_poke_pete

Sep 27, 2026

bookworm370 said:
Thanks, but until they do, can't Dish just revert to the old driver that worked? Then test the new driver when delivered,d before pushing it again.

But then what does an old CIO know! I've only reamed quite a few buttholes from my people that didn't do that!

dish can't revert back to older drivers or updates. although just one reason not to buy the ota dongle!!!

Reactions: charlesrshell

ppappas

Sep 30, 2026

slow_poke_pete said:
dish can't revert back to older drivers or updates. although just one reason not to buy the ota dongle!!!

They can absolutely put the old driver back if they wanted. This is an embedded software environment in which they have total control. All they have to do if build a new version of firmware with the old OTA driver and test it of course. They just don't want to spend the resources doing so. If they are not going to continue supporting the single tuner adapter, then they have to say so.

Reactions: slow_poke_pete and charlesrshell

Almighty1

Oct 1, 2026

ppappas said:
They can absolutely put the old driver back if they wanted. This is an embedded software environment in which they have total control. All they have to do if build a new version of firmware with the old OTA driver and test it of course. They just don't want to spend the resources doing so. If they are not going to continue supporting the single tuner adapter, then they have to say so.

Unless of course they didn't keep a copy of the old drivers and can no longer get it. Then there is always the their support for the product is EOL after a x amount of time so it will make the consumer have to buy the current product offering.

Reactions: slow_poke_pete and charlesrshell

Briant73

Yesterday at 9:19 PM

Anyone heard any updates on this, I'm still having the issue so thought I'd check in.

Reactions: charlesrshell

Almighty1

Yesterday at 9:48 PM

Briant73 said:
Anyone heard any updates on this, I'm still having the issue so thought I'd check in.

No updates but if you can get DISH Technical Operations to roll you back to H710 or earlier even though H708 would be best because it also eliminates another problem like in this comment, you will also no longer have the problem as long as you don't update manually or forced to any new version until the problem is fixed as the problem started in H711 and still exist in H712 and H713.

https://www.satelliteguys.us/xen/th...ftware-version-713-is-out.423921/post-5108817

Reactions: charlesrshell

dishstaller

Yesterday at 9:57 PM

Installed an off-air antenna a couple days ago for a customer who had just cancelled his Dish service. He had a dual off-air adapter and gave it to me. Cool. I'll keep it on the truck....might come in handy. Got to admit I don't watch anything as far as live tv goes anymore. Even if we have severe weather, our local channels will have a live feed on Youtube.

Reactions: navychop and charlesrshell

navychop

Yesterday at 11:21 PM

In other news, it was announced that the software fix for the two tin cans and a string will not be forthcoming. A hardware fix is required. However, that fix will let you receive stations from a gazillion miles away.

Truck roll charges may apply. Two year commitment required.

Reactions: Bobby, dishstaller and charlesrshell

View all replies (201)

MartyDe

Last reply Yesterday at 10:37 PM · posted in Over the Air Television By RabbitEars.Info

ATSC 3 converter boxes

Interesting article about the work being done to develope an ATSC 3 converter box. Yes it does mention affordable.

Pearl TV Issues Progress Report on Low-Cost 3.0 Converters in Advance of NAB Show New York

Group has secured lower pricing from key tech players to make less costly boxes available

www.tvtechnology.com

6 Replies · 207 views

Load Replies (6) Reply Legacy View

navychop

Tuesday at 12:03 PM

DEATH TO NEXGEN!

Reactions: primestar31, RaVo68, gms49ers and 1 other person

TRG

Tuesday at 12:12 PM

17 years ago the US turned off analog OTA signals in favor of digital broadcasting. Now the push is ATSC 3 "Nextgen TV". But nobody seems to be able to agree on DRM implementation protocols. People don't want to hook their TV up to the internet in order to watch over the air TV. At least I don't. With all the data they collect about your viewing habits the box should be given away at no cost.

Reactions: N5XZS, osu1991, slow_poke_pete and 1 other person

navychop

Tuesday at 12:27 PM

Comb your hair.

primestar31

Yesterday at 7:29 PM

navychop said:
DEATH TO NEXGEN!

It's dead, they just don't know it yet. They killed it by forcing DRM on it, and that TOTALLY botched implementing it.

There is absolutely NO compelling reason for anybody to switch to ATSC3.0. They only want it as a total and complete money grab.

Reactions: FTA4PA and navychop

navychop

Yesterday at 10:37 PM

I truly hope you are right.

Reactions: FTA4PA

View all replies (6)

Top

Back

Search

Search

Social Feed

installing a slimline

Project Helix Price Rumor: Could the Next Xbox Cost $1,800? #shorts

Song Name Game Part 3!

iPhone Duo Crease?

Reading on the iPhone Duo!

Playing Xbox on the iPhone Duo!

iPhone Duo Fold Animation

Its crazy how the ViP922 is so rare for no reason.

Country singer John Anderson died today

OTA no working after Update

ATSC 3 converter boxes

Pearl TV Issues Progress Report on Low-Cost 3.0 Converters in Advance of NAB Show New York