Social Feed

BobMurdoch
Supporting Founder
Last reply · posted in DISH Network Support Forum
OK, here's my situation.....

Before 11/29:
I've got a Dish500 looking at 110/119 and a Dish300 looking at 61.5. They feed into a SW64 which then feeds a 721 and 2 Dishplayers. I want to add another receiver in my house but my ports are maxed out on the SW64. I figure it will cost me $500+ to upgrade to the additional receiver due to a new SW64, 3 switches to split 110, 119, and 61.5, plus the cabling and labor.

Then I hear about THE Deal. Extend my commitment 2 years and E* will (holds breath), Give me a 510 free and clear (AEP here so no PVR fee), give me a SW64, give me the three other switches to split the dish feeds, give me the cabling, and the professional install. My cost.... ZIP as I was going nowhere anyway so the commitment was a no brainer.

On 11/29...

The installer (who I find out is based in Brick, NJ... a mere 5 minutes from Brielle and who is now going to be my installer of choice if I make any changes that E* doesn't pay for), sees my SW64 hanging loose down in my basement and says that he'll make sure all the things he has to do will look neat when he is done. He asks for a small square scrap piece of plywood that he drills into the cinder block wall. He mounts my SW64, the new SW64, and the three smaller switches to spilt the feeds. He runs all the wires and snakes the cable to the new bedroom receiver neatly. When it is all done, it is a thing of beauty as all the wires are neat, the smaller switches are labeled with which satellite (110/119/61.5) they are receiving, and the receiver is put into place. I swapped my Dishplayer to my daughter's room (the new outlet) and took the new 510 for the master bedroom. Everything works fine on the first try. It takes about 2.5 hours.

Charlie gets grief when he gets it wrong, so he is going to get huge accolades for doing this right. It cost me $0 out of pocket, and the additional TV only cost me the $5 additional receiver fee per month. I've discovered a new installer who impressed the hell out of me with his professionalism and talent, as well as his willingness to take the extra time and go above and beyond what was expected. I'm still impatient waiting for the 921 to ship, but you did this 3 yr+ subscriber right. Bravo.
6 Replies · 2301 views
BobMurdoch
I'll scream when they screw up (which I did in another post two weeks ago when they tried to install it two weeks ago, but the CSR put on the work order that it was a swap for a 2700 that I didn't have. The installer got on the phone with a different CSR and got it all straightened out.)

I'm more patient than the average Joe, especially when the word FREE is thrown around, so the experience was still a highly positive one.

Any word on the 921s? I'm still hitting Sears.com daily to see if anything changes, but I am desperately hoping I can get this installed before Christmas......
Scott Greczkowski
I believe that the chance of getting a 921 before Christmas is really slim.

I hear that less then 200 921's will be made available on the 8th.

I KNOW that is not enough to fill all the orders, that is unless people are on many waiting lists.

I am also hearing that while Sears stores may get display units they might not get any stock to sell until possibly February.
RobbinM
Scott Greczkowski said:
I believe that the chance of getting a 921 before Christmas is really slim.

I hear that less then 200 921's will be made available on the 8th.

I KNOW that is not enough to fill all the orders, that is unless people are on many waiting lists.

I am also hearing that while Sears stores may get display units they might not get any stock to sell until possibly February.

Scott, can you post the size (or least scale) of your pre-orders and waiting list for comparsion?
D
Scott Greczkowski said:
I believe that the chance of getting a 921 before Christmas is really slim.

I hear that less then 200 921's will be made available on the 8th.

I KNOW that is not enough to fill all the orders, that is unless people are on many waiting lists.

I am also hearing that while Sears stores may get display units they might not get any stock to sell until possibly February.

Those are the 200 Sears display models. Look and drool until after Xmas :)
H
Scott Greczkowski said:
I believe that the chance of getting a 921 before Christmas is really slim.

I hear that less then 200 921's will be made available on the 8th.

I KNOW that is not enough to fill all the orders, that is unless people are on many waiting lists.

I am also hearing that while Sears stores may get display units they might not get any stock to sell until possibly February.

Would that include the JVC version as well?
Scott Greczkowski
Staff member HERE TO HELP YOU! Cutting Edge
Last reply · posted in The Chit Chat Club
Sometimes a thread gets so many posts in it that is can cause issues for the server so that why today we introduce The Song Name Game Part 3!

So let the game continue!

The last song was added by Bobby who posted...

One Meat Ball - Andrews Sisters

CONTINUE ON AND HAVE FUN! WELCOME HOME TO SATELLITEGUYS.US!

Here are the original rules for the game as posted by WebbyDude back in 2006. http://www.satelliteguys.us/threads/68645-Song-Name-Game

Just name a song title and the band who performed it. The next person does the same thing, but needs to list a song title or band name which includes a word from the previous entry. Pick songs from any genre.

Example:

Long Live Rock and Roll -- Rainbow

Rainbow in the Dark -- Dio

Another example:

Ride the Lightning -- Metallica

Lightning Strikes -- Ozzy Osbourne


Get it?


An additional note: we all know that song titles, sometimes, use profane words. Because this is a family friendly website it is advised that you clean up that title up a bit. This is accomplished by using something like sh!t instead of the real word. Thanks....
68565 Replies · 2675567 views
  • Like
Reactions: c-spand
dishstaller
Little Miss Dangerous - Ted Nugent
RaiderPower
Little Miss Can't Be Wrong - Spin Doctors
  • Like
Reactions: FTA4PA
sdfntx
Jump Down, Spin Around - Harry Belafonte
  • Like
Reactions: Bobby
long_time_Dish
Stop Draggin' My Heart Around - Tom Petty and Stevie Nicks
H
This Old HEART Of Mine(Is Weak For You)-The Isley Brothers
iJustine
Last reply · posted in iJustine
1 Replies · 9 views
T
It's not even where it folds!
SuperDish_Fan23
Last reply · posted in DISH Network Support Forum
Why are ViP922s So rare? like its crazy how ebay has none, i checked everywhere, also, i got a ViP222k now, which is actually activated!
20 Replies · 500 views
S
That's not really unusual. Cable companies like to the provide the box too. The phone company provided the phones in until the government forced them to allow third-party phones.
  • Like
Reactions: charlesrshell
Almighty1
That's not really unusual. Cable companies like to the provide the box too. The phone company provided the phones in until the government forced them to allow third-party phones.
Yes, the Western Electric phones that says "Bell System Property, NOT FOR SALE, Western Electric".
AZ.
AZ.
Yes, the Western Electric phones that says "Bell System Property, NOT FOR SALE, Western Electric".
someone is showing their age
Almighty1
someone is showing their age
LOL. It depends if the person saw it during the years when they were actually still available which is 1968 to 1983 meaning the person could be 43-58 years old or they can even be a few years old if they learned to read and write at a young age and actually saw a telephone with that label somewhere recently just like even here in San Francisco, payphone still exist physically in public places but whether they can be used or not is a different issue. It still looks like this even today:
1792633296785.webp
  • Like
Reactions: charlesrshell
dishstaller
I opened my Radio Shack in Sept 1984 and right about that time they did the whole deregulation thing with the phone companies. I bought TONS of those phones that had been refurbished with a new outer shell. You could throw one of those out of a 3 story high window and it would still work.
That was an interesting time in history. I would have older customers come in and ask about phones.....they were terrified that they were going to get into trouble hooking up a second phone without the phone company knowing about it. One of the funniest episodes of WKRP was the one where Johnny thought the cops were showing up because they had an unregistered phone. I guess younger folks can't conceive of a time when you were limited to the number of phones you could have in your house....and limited to the length of the cord 🤣
navychop
someone is showing their age

You should hear his stories about when rocks were soft and pterodactyls were the new kid on the block!
dishstaller
One of the funniest episodes of WKRP was the one where Johnny thought the cops were showing up because they had an unregistered phone.

View: https://www.youtube.com/watch?v=CA0yZ1nrm6M&pp=ygUPd2tycCBwaG9uZSBjb3Bz
dishstaller
Pub Member / Supporter Lifetime Supporter
Last reply · posted in The Chit Chat Club
He was 71 yrs old. One of my favorite songs is Seminole Wind....the violin is killer.


View: https://www.youtube.com/watch?v=W8sh9P3X33w
5 Replies · 45 views
FTA4PA
Rest In Peace
  • Like
Reactions: dishstaller
M
I Wish I Could Have Been There is an amazing song. Rest in peace Mr Anderson.
  • Like
Reactions: dishstaller
Bobby
Rest in peace.
  • Like
Reactions: dishstaller
comfortably_numb
Hope you're out there Swingin', John.
  • Like
Reactions: dishstaller
dishstaller
I Wish I Could Have Been There is an amazing song.
That's one of those songs that hits a little too close to home for me. I like the song but just can't listen to it. It's kinda like that song "Daddy never was the Cadillac kind".....reminds me too much of my Grandfather who died Feb 18, 1995.
N
Last reply · posted in DISH Network Support Forum
My OTA is not working anymore. This started after the latest update. I have the OTA dongle with a OTA antenna that I've been using for years. My hopper does not recognize the dongle anymore and when I go to the OTA setting, it has a screen that says to plug a dongle into the USB. I tried unplugging and plugging back, in the same usb port and other ports. The Hopper does not recognize it. Anyone have same issue?
201 Replies · 5114 views
  • Like
Reactions: charlesrshell
Scott Greczkowski
Did you people having this issue contact Brittany yet? Shes trying to keep track of things and it would be good for you to contact her as maybe she can get this somewhere and get fixed.

Now while unofficial, I am hearing this issue wasn't caused by DISH's software team, but was caused by a chipset driver update that seemes to have hosed some older USB devices. If this is indeed the case I can see why DISH didn't know and why they are slow in fixing it as they need the chipset company to fix its drivers and release them to DISH so they can be pushed out to all.

DISH does not hate you guys nor do they want you to buy new USB dongles. I am rather sure they didn't even know this was an issue until they saw it posted.

Again contact Brittany if you are having this issue, so she has your info and hopefully she can do something for you to keep you happy. :)
bookworm370
Did you people having this issue contact Brittany yet? Shes trying to keep track of things and it would be good for you to contact her as maybe she can get this somewhere and get fixed.

Now while unofficial, I am hearing this issue wasn't caused by DISH's software team, but was caused by a chipset driver update that seemes to have hosed some older USB devices. If this is indeed the case I can see why DISH didn't know and why they are slow in fixing it as they need the chipset company to fix its drivers and release them to DISH so they can be pushed out to all.

DISH does not hate you guys nor do they want you to buy new USB dongles. I am rather sure they didn't even know this was an issue until they saw it posted.

Again contact Brittany if you are having this issue, so she has your info and hopefully she can do something for you to keep you happy. :)
Thanks, but until they do, can't Dish just revert to the old driver that worked? Then test the new driver when delivered,d before pushing it again.

But then what does an old CIO know! I've only reamed quite a few buttholes from my people that didn't do that! ;)
S
Thanks, but until they do, can't Dish just revert to the old driver that worked? Then test the new driver when delivered,d before pushing it again.

But then what does an old CIO know! I've only reamed quite a few buttholes from my people that didn't do that! ;)
dish can't revert back to older drivers or updates. although just one reason not to buy the ota dongle!!!
  • Like
Reactions: charlesrshell
ppappas
dish can't revert back to older drivers or updates. although just one reason not to buy the ota dongle!!!
They can absolutely put the old driver back if they wanted. This is an embedded software environment in which they have total control. All they have to do if build a new version of firmware with the old OTA driver and test it of course. They just don't want to spend the resources doing so. If they are not going to continue supporting the single tuner adapter, then they have to say so.
Almighty1
They can absolutely put the old driver back if they wanted. This is an embedded software environment in which they have total control. All they have to do if build a new version of firmware with the old OTA driver and test it of course. They just don't want to spend the resources doing so. If they are not going to continue supporting the single tuner adapter, then they have to say so.
Unless of course they didn't keep a copy of the old drivers and can no longer get it. Then there is always the their support for the product is EOL after a x amount of time so it will make the consumer have to buy the current product offering.
B
Anyone heard any updates on this, I'm still having the issue so thought I'd check in.
  • Like
Reactions: charlesrshell
Almighty1
Anyone heard any updates on this, I'm still having the issue so thought I'd check in.
No updates but if you can get DISH Technical Operations to roll you back to H710 or earlier even though H708 would be best because it also eliminates another problem like in this comment, you will also no longer have the problem as long as you don't update manually or forced to any new version until the problem is fixed as the problem started in H711 and still exist in H712 and H713.
  • Like
Reactions: charlesrshell
dishstaller
Installed an off-air antenna a couple days ago for a customer who had just cancelled his Dish service. He had a dual off-air adapter and gave it to me. Cool. I'll keep it on the truck....might come in handy. Got to admit I don't watch anything as far as live tv goes anymore. Even if we have severe weather, our local channels will have a live feed on Youtube.
navychop
In other news, it was announced that the software fix for the two tin cans and a string will not be forthcoming. A hardware fix is required. However, that fix will let you receive stations from a gazillion miles away.

Truck roll charges may apply. Two year commitment required.
M
Last reply · posted in Over the Air Television By RabbitEars.Info
Interesting article about the work being done to develope an ATSC 3 converter box. Yes it does mention affordable.
6 Replies · 216 views
navychop
DEATH TO NEXGEN!
TRG
TRG
17 years ago the US turned off analog OTA signals in favor of digital broadcasting. Now the push is ATSC 3 "Nextgen TV". But nobody seems to be able to agree on DRM implementation protocols. People don't want to hook their TV up to the internet in order to watch over the air TV. At least I don't. With all the data they collect about your viewing habits the box should be given away at no cost.
navychop
Comb your hair.
primestar31
DEATH TO NEXGEN!
star trek GIF


It's dead, they just don't know it yet. They killed it by forcing DRM on it, and that TOTALLY botched implementing it.

There is absolutely NO compelling reason for anybody to switch to ATSC3.0. They only want it as a total and complete money grab.
  • Like
Reactions: FTA4PA and navychop
navychop
I truly hope you are right.
  • Like
Reactions: FTA4PA