Social Feed

Fabric8r
Last reply · posted in DISH Network Support Forum
Hello everyone.

My 942 arrived. The installer is scheduled for this Thursday, but being an Electrician, I thought I could hook this receiver up myself and save the $50.00 installation charge. Well, I did everthing right according to the book, and my own smartz. Plugged it in, it powered up, got the green light, got the yellow light on TV1 But nothing on the TV, blank, zip, nada. Tried every conceivable connection, nothing. Called Dish CSR, who said I should have something on my screen, and was told to call back when I do.

I have the dish 500 (legacy) system, sw21 (if I remember correctly) switches, first cable is plugged into Sat 1 and the other is into Sat 2. Phone plugged in. Hookups to both TV's are correct.

I guess I have resided to the fact I will wait for the installer to show up, and pay the install fee. But, since this forum has been a great help so far, I may not give up yet..... any suggestions? Did I miss something?
4 Replies · 1696 views
J
Fabric8r said:
Hello everyone.
I have the dish 500 (legacy) system, sw21 (if I remember correctly) switches, first cable is plugged into Sat 1 and the other is into Sat 2. Phone plugged in. Hookups to both TV's are correct.
The SW21 switch is for connecting another dish to your existing dish500 unless you have dish500 upgrade (two single LNBs instead of one twin LNB). Each line should go from dish to each tuner input of the 942.

On TV1 side are Y,Pr,Pb connections that go to your HD set. You may use the HDMI cable instead which connects from receiver to the HDMI or DVI-D connector (if using supplied convertor cable). For TV1 you must connect to either the component inputs or through the HDMI (do not use composite inputs because those are TV2 only. On the front panel the TV1 light should be on and also one of the modes lights. Try to toggle the input and menu buttons. You should see something even if dish coax isn't connected correctly.
Fabric8r
The Dish 500 I have are two LNBs sitting next to each other (not the newer dual ones with a cover over both) with two cables coming out of each. Each dual cables connect to a sw21. There are two sw21s. One cable from each runs into the house. One was connected to my 7200 receiver, the other to my 311 receiver. I just took the one from the 7200 and plugged it in to SAT 1 in the new 942, and the other one that was connected to my 311 I connected to SAT 2 in the 942.

In the back of the 942, the TV1 component cables are to my HD TV (Proscan PS36800HR) and I ran a RG6 from TV2 down to my other television (not HD)

Nothing on the screen.


I will do some more fiddling tonight, but dang, can't figure out what I am doing wrong. I could easily consume the $50.00 install fee in beer, so don't want to fiddle too much. (or do I?)

Thanks for your help.
SimpleSimon
Fabric8r said:
being an Electrician, I thought I could hook this receiver up myself
Glad you're here - hopefully, you'll be better at low-voltage work because of it. :up

Nothing personal, but you know what a satellite installer dreads hearing more than anything else?
"My electrician pre-wired the house". :yikes

Anyway, forget about your satellite feeds until you get a picture. "Every conceivable" connection is not likely. That would be HDMI, DVI, Component, S-Video, Composite, and RF - some on TV1 some on TV2.

Start with the basics. Find a yellow jack on the 942. Run it to a yellow jack on the TV. If the TV doesn't have any yellow jacks, well, it's the wrong TV. Select the correct input on the TV. Method varies by TV model, so it's hard to help you there.
Fabric8r
Here is an update, for those interested.

The inataller showed up, looked at what I had, and said it was hooked up correctly, and could never figure out why there was a blank screen. After 20 minutes with a tech at DishNetwork, they determined the receiver was defective. Was not sending an output signal on the TV1 (HD) side.

The tech, nor the installer could do anything else, and I was told I would receive a phone call that would authorize a new receiver to be sent to me. No phone call yet. Hope they do soon, they didn't waste any time processing my credit card payment. Probably will be at least another week to receive the new receiver. Grrrrr.

:no
zippyfrog
Pub Member / Supporter Lifetime Supporter
Last reply · posted in DISH Network Support Forum
Over the past year I have been tracking the changes on Western Arc. The past 3 months have had a lot of changes that I posted in the other MPEG2 Western Arc shutdown thread. Now that 129 is (basically) out of commission, here is where Western Arc stands. This is just a national channel list, (no local channels) based off what I can see and what others have contributed. Thanks to everyone who has helped me come up with the locations of some of the channels – I would try and list all of you out, but I know I would forget someone! As has been suggested in other parts of the forum, it would be great to collect the spotbeam data for those who could contribute!

A couple of pieces of info:
  • Out of the 64 transponders between 110/119, there are currently 50 transponders that Dish is licensed to use. 22 are Spotbeams, 28 are ConUS transponders (14 transponders are licensed to DirecTV and Dish doesn't have access to them)
  • Those 28 ConUS transponders are divided as follows:
    • 10 are dedicated to National HD channels (ESPN, CNN, Disney Channel, etc). Dish is maxing out at 16 HD channels per transponder (note – in an earlier post I said there was one transponder with 17 HD channels, that was an error on my part. When I double checked my listings, one channel changed transponders). Before the transition, there was a maximum of 14 HD channels per transponder.
    • 1 transponder is dedicated to adult content
    • 2 are a mixture HD PPV Movies/4k channels
    • 3 are set aside for HD Sports channels that are only on for live games (NBA League Pass, the PAC 12 alternate channels, some PPV events, etc); 3 SD PPV Sports Channels are there as well.
    • 7 are for SD and/or music channels. Dish is maxing out at 26 SD channels per transponder thus far on the SD transponders.
    • 5 transponders on 110 I have no channels listed but Dish operates. (they are labeled as ConUS on my chart below) There are other things that could be on those transponders, like RV Distant Networks, internal testing channels, etc, that I can't see. They might be able to be used for additional content, but I am not sure exactly what is on those transponders.
There are two transponders that have lower than normal SD channels – 110, TP 21 and 119, TP 19. Previously those transponders contained the programming guides that get downloaded from the satellite when the receivers download EPG. I assume that is where the programming guides are still downloaded from, thus less channels there.

When I talk about number of channels on a transponder, all my numbers are unique channels – for example, channel 101 and 199 are the same channel mapped to two different numbers, but in terms of space, only takes up 1 channel worth of bandwidth on the transponder.

Finally, I have to give Dish a ton of credit. When it was 110/119/129, Dish had 82 transponders they were using – it took a lot to get it down to 50 transponders and figure out where all the pieces were going to go. What are the things they did to get there? Here are the things I saw:
  • During this migration from 129, Dish converted 7 ConUS transponders on 119 into Spotbeams – that is how they ended up fitting on all the HD locals that used to be on 129. (for those interested, TP 6, 7, 8, 9, 10, 11, 13 are the ones that used to be ConUS on 119 that are now Spotbeam)
  • Removed almost all SD duplicate channels that are offered in HD
  • Converted remaining SD channels from MPEG2 to MPEG4
  • There are also 2 subtle things that changed from the HD channel perspective
    • At the beginning of the transition, Dish decreased the number of PPV Movie channels – prior to this transition the PPV channels HD PPV movies were 502-522; now they are 502-517.
    • At the beginning of April when MLB, NBA, and NHL regular seasons were all going on at the same time and this transition began, there were a ton of games "joined in progress" for the HD feeds. That wasn't common since the days before the full time HD RSN's. The reason for that was prior to the transition, Dish had 4 transponders set aside for HD Sports – 2 transponders was the bandwidth set aside from the HD RSN's before Dish dropped the RSN's, then 2 transponders were for alternate channels. Now we are down to 3 transponders for HD sports.
252 Replies · 66173 views
zippyfrog
Dish has officially removed all the locals from 119 and they are all on 110 now. TP 02, 04, 06, 08, 10 were all functioning as Spotbeams as of last week, but now they are ConUS.

This means all 21 transponders that Dish has access to at 119 are now ConUS.
  • Like
Reactions: charlesrshell
D
Dish has officially removed all the locals from 119 and they are all on 110 now.
Might be a silly question, but does this mean ALL 29 TP's on 110 are positively spot beams now?
zippyfrog
Might be a silly question, but does this mean ALL 29 TP's on 110 are positively spot beams now?
Nope - TP 1-13 are still ConUS on 110. Which is crazy...there are so many different spotbeams on the new 110 satellite compared to the older 110 or 119. Now, someone can correct me if I am wrong on this - but aren't there two satellites at 110 right now? If so, it looks like TP 1-13 are coming from the old satellite at 110 and 14 onward are spotbeams on the new satellite.
  • Like
Reactions: charlesrshell
D
Now, someone can correct me if I am wrong on this - but aren't there two satellites at 110 right now?
Hopefully nelson61 can chime in on this one, because I'm not sure, either.
I guess the thing I'm really perplexed about, is if there are NO more locals - at least on spotbeams - on 119, then how DID they cram ALL the locals on 110 & NOT have ALL those x-ponders in SB mode by now?
  • Like
Reactions: charlesrshell
zippyfrog
Hopefully nelson61 can chime in on this one, because I'm not sure, either.
I guess the thing I'm really perplexed about, is if there are NO more locals - at least on spotbeams - on 119, then how DID they cram ALL the locals on 110 & NOT have ALL those x-ponders in SB mode by now?

Here was a comment by nelson61 last year:
EchoStar 23 (Conus beam) will still be at 110W so there can be some Conus beam coverage from 110W depending on how many transponders they use for the spots.
In the same thread, he gave all the kml files for the spotbeams to put on Google Earth, and it looks like there are a lot more spotbeams per transponder available than the old satellite. My gut is that there is just a more technilogically advanced satellite, and can handle more channels.

I would love an analysis of how many channels could be fit on all the spots!
meStevo
Lifetime Supporter
Last reply · posted in The Chit Chat Club
Continuing the Kilauea thread in the Pub here. Perhaps the Iceland one too next time there's remarkable activity.

Currently there is precursory lava flowing into the crater, leading to the next episode that'll probably start within the next day.

You can see the pace of inflation / deflation here. It serves as the primary predictor for when the expect the eruptions, which coincide w/ inflation turning into significant deflation and last for several hours on average with significant fountaining.



View: https://youtu.be/Uecu2seh4b4


Wife and I like the AfarTV feeds, for the discussion along w/ them, though they're otherwise just mirrors of the official USGS feeds.


View: https://youtu.be/iws3rh5vLAQ
122 Replies · 3598 views
  • Like
Reactions: osu1991
Foxbat
Oooo, quite the show now. All three vents have doming and overflows. The cone that built up around the North vent lost its upper quarter at 02:50 Oct 17 and is now spewing lava at a healthy rate. Don't know if I would say it's a fountain, but it's close.


IMG_1534.webp

edit: The USGS has called the official start of Episode 55 as starting at 03:19 HST Oct 17, 2026:

Alert Level: WATCH, Color Code: ORANGE 2026-10-17 13:43:56 UTC
HVO/USGS Volcanic Activity Notice

Volcano: Kilauea (VNUM #332010)

Current Volcano Alert Level: WATCH
Current Aviation Color Code: ORANGE

Issued: Saturday, October 17, 2026, 3:43 AM HST
Source: Hawaiian Volcano Observatory
Notice Number: 2026/H488
Location: N 19 deg 25 min W 155 deg 17 min
Elevation: 4091 ft (1247 m)
Area: Hawaii

Summary: Episode 55 of the ongoing Halemaʻumaʻu eruption began at 3:19 AM HST on October 17, 2026.

Volcanic Activity:
Episode 55 of lava fountaining in Halemaʻumaʻu began at the summit of Kīlauea began at 3:19 AM HST on October 17, 2026.

Fountain heights are relatively low at about 100-150 feet (30-45 m), and it is not clear whether this episode will evolve to the same heights as previous episodes. Continuous overflows from the vents began yesterday, October 16, just before 6 a.m. HST and transitioned into episode 55 fountains at 3:19 a.m. HST this morning. The current forecast is for winds are blowing from the north-northeast direction, which suggests that volcanic gas emissions and volcanic material may be distributed to the south-southwest direction from Halemaʻumaʻu.
  • All eruptive vents and lava flows are confined to Halemaʻumaʻu crater within Hawaiʻi Volcanoes National Park. Tephra fall from volcanic ash clouds is greatest within 3 miles (5 km) of the vents, lighter ash and Pele's Hair may stay suspended for large distances from the vents.
Foxbat
Kīlauea seems to be returning to the "normal" eruption script, impressive fountaining from the North Vent. For once, the V2 Cam has the best overall shot:
IMG_1535.webp
The lava flows have covered a good portion of the Halemaʻumaʻu crater floor.
Foxbat
Looks like Episode 55 is over at 09:00 HST, just under six hours. The USGS said the fountains reached 720' or 220 meters.
​
  • Like
Reactions: RaiderPower
Foxbat
The USGS Kīlaeua Webcam #1 has been showing overflows and doming from the North vent overnight. Maybe the volcanic plumbing has settled back into its two-three week cycle of fountaining?

But I do miss the little cinder cone that broke up in the last episode.
Foxbat
Sorry, I should have posted these earlier:

​

We're still waiting on the start of Episode 56.
Scott Greczkowski
Staff member HERE TO HELP YOU! Cutting Edge
Last reply · posted in The Chit Chat Club
Sometimes a thread gets so many posts in it that is can cause issues for the server so that why today we introduce The Song Name Game Part 3!

So let the game continue!

The last song was added by Bobby who posted...

One Meat Ball - Andrews Sisters

CONTINUE ON AND HAVE FUN! WELCOME HOME TO SATELLITEGUYS.US!

Here are the original rules for the game as posted by WebbyDude back in 2006. http://www.satelliteguys.us/threads/68645-Song-Name-Game

Just name a song title and the band who performed it. The next person does the same thing, but needs to list a song title or band name which includes a word from the previous entry. Pick songs from any genre.

Example:

Long Live Rock and Roll -- Rainbow

Rainbow in the Dark -- Dio

Another example:

Ride the Lightning -- Metallica

Lightning Strikes -- Ozzy Osbourne


Get it?


An additional note: we all know that song titles, sometimes, use profane words. Because this is a family friendly website it is advised that you clean up that title up a bit. This is accomplished by using something like sh!t instead of the real word. Thanks....
68741 Replies · 2684359 views
  • Like
Reactions: c-spand
Bobby
The Saints Are Coming - U2
dishstaller
Coming Back to Life - Pink Floyd
  • Like
Reactions: gms49ers
gms49ers
Echos - Pink Floyd
  • Love
Reactions: dishstaller
dishstaller
Echoes in the Rain - Enya
  • Like
Reactions: Bobby
gms49ers
Fool in the Rain - Led Zeppelin
TWiT Tech Podcast Network
· posted in TWiT Tech Podcast Network
0 Replies · 3 views
dishstaller
Pub Member / Supporter Lifetime Supporter
Last reply · posted in The Chit Chat Club
Now first, I'll mention that the area of FL I live in has extremely high humidity and not a lot of wind so things don't dry out very well for extended periods of time.
I'm in the process of tearing down and rebuilding a pergola with a surrounding deck that I built 9 yrs ago. 90% of the deck screws are just sheering off at the head because the screws rusted out. These are the deck screws you buy in the 25 lb box at your lumber yard. Very annoying. So I just ordered some 316L stainless steel screws to use for when I go to rebuild it.
3 Replies · 52 views
  • Like
Reactions: Foxbat
AZ.
AZ.
Now first, I'll mention that the area of FL I live in has extremely high humidity and not a lot of wind so things don't dry out very well for extended periods of time.
I'm in the process of tearing down and rebuilding a pergola with a surrounding deck that I built 9 yrs ago. 90% of the deck screws are just sheering off at the head because the screws rusted out. These are the deck screws you buy in the 25 lb box at your lumber yard. Very annoying. So I just ordered some 316L stainless steel screws to use for when I go to rebuild it.
Screws are all crap, soft and useless! Sick of going through 3 to get one not to break, strip or shear! I aint that strong in my old age!
T
Well, isn't removal of screws intrinsically much tougher than drive-in, simply because over time they become more adhered to the wood, whether or not they actively rust? Possibly there could be less of that effect with stainless.
dishstaller
Well, isn't removal of screws intrinsically much tougher than drive-in, simply because over time they become more adhered to the wood, whether or not they actively rust?
I have seen that happen that not in this case. I had also used some screws from an old box I had that I needed to use up....didn't think much of it at the time. ALL of THOSE screws came out perfectly and had virtually no rust on them. The ones that you find at your lumber yard....those with the orange snap on lids were mostly rust. The problem with the heads sheering off was that I had to get my crowbar and pry each board up one joist at the time. Took a simple job and made it 1000% harder.

As for adhering to the wood...true story. Back when hurricane Michael hit, it almost took the weather vane off of the old milk barn behind my parent's house. I climbed up on the roof and only one nail was still holding it. Grabbed my hammer and tried to pull it out...wasn't budging. Grabbed a short crowbar (all I had access to) wouldn't budge. Ended up cutting the stupid nail so I could get the weather vane. Barn was built in the late 40s, I guess the nail had become one with the pine lumber used to build the barn.
osu1991
Pub Member / Supporter
Last reply · posted in Movie Talk
1 Replies · 12 views
  • Like
Reactions: dishstaller
dishstaller
Yep....looking forward to it.
ewindowman
Lifetime Supporter
Last reply · posted in DISH Network Support Forum
Looks like dish is Bankrupt. Filling tomorrow Tuesday June 30th
443 Replies · 15160 views
nelson61
Washington Post

SpaceX has held talks with Boost's parent company EchoStar in recent months about launching its own signature wireless service through a deal with the company, according to two people familiar with the negotiations.
Musk, the SpaceX CEO, has discussed the deal personally, meeting with EchoStar chairman Charlie Ergen last month, according to the people. The potential deal may result in SpaceX acquiring Boost Mobile or SpaceX gaining access to its network, which it leases from AT&T and T-Mobile US, the people said.
Access to those lease agreements would be a coup for SpaceX. The back door would allow Musk to make a play for a U.S. wireless market that equity research firm MoffettNathanson estimates is worth $235 billion. But the proposed service may need consent from those carriers for the service to actually launch, the people said.
Scott Greczkowski
Washington Post

SpaceX has held talks with Boost's parent company EchoStar in recent months about launching its own signature wireless service through a deal with the company, according to two people familiar with the negotiations.
Musk, the SpaceX CEO, has discussed the deal personally, meeting with EchoStar chairman Charlie Ergen last month, according to the people. The potential deal may result in SpaceX acquiring Boost Mobile or SpaceX gaining access to its network, which it leases from AT&T and T-Mobile US, the people said.
Access to those lease agreements would be a coup for SpaceX. The back door would allow Musk to make a play for a U.S. wireless market that equity research firm MoffettNathanson estimates is worth $235 billion. But the proposed service may need consent from those carriers for the service to actually launch, the people said.
Can't remember where or who I saw predict this. :D

It wouldn't surprise me to see Elon soon own all of DISH / Echostar in the future.
MikeD-C05
Can't remember where or who I saw predict this. :D

It wouldn't surprise me to see Elon soon own all of DISH / Echostar in the future.
So Charlie is going to sell out and give it all the Elon?
  • Like
Reactions: charlesrshell
Bruce
It wouldn't surprise me to see Elon soon own all of DISH / Echostar in the future.
Again, why would Musk want a TV Service, specially one that is losing over a million subscribers a year.

Phone service…maybe, but not TV.
Scott Greczkowski
So Charlie is going to sell out and give it all the Elon?
I would say yes, but he will stay on board with Elon somehow.
Scott Greczkowski
Again, why would Musk want a TV Service, specially one that is losing over a million subscribers a year.

Phone service…maybe, but not TV.
I know he wants TV. He wants to deliver EVERYTHING to EVERYWHERE.
Bruce
I know he wants TV. He wants to deliver EVERYTHING to EVERYWHERE.
Again, if so, why would he want Dish/Sling of all the providers?

He could deliver anything without actually owning, for example, watching the Lions game in my Tesla Y on it's screen via the YT app, while on the way to my future in-laws on Sunday.
rvvaquero
If Musk did acquire DISH, he would just convert it to use his own satellites to deliver it. Might be easier than creating a new startup. Change my dish out to one which connects to Starlink? Who knows?
S
  • Like
Reactions: charlesrshell
teachsac
Staff member HERE TO HELP YOU!
Last reply · posted in Internet Television (IPTV) Discussion Forum
30 Replies · 1102 views
Bruce
AMC+ is on sale for $40 for the year, the no commercials plan.

For basically $3.34 a month, thought I would give it a try again.

Today is the last day for the deal.
R
AMC+ is on sale for $40 for the year, the no commercials plan.

For basically $3.34 a month, thought I would give it a try again.

Today is the last day for the deal.
Thanks for spending my $$. I figured I would try it also.
navychop
Hmmmm.
Jimbo
We should be coming into the Streaming Deals time of year :)

I will be looking for Yearly deals, not the 7 day trial or a 1 month deal like we had the last year or so.
  • Like
Reactions: Foxbat
Jimbo
I just managed to get 30% on Paramount Plus Commercial Free Yearly ... total was $99.
I haven't gotten the 50% off deal in a few years, so when she said $99, I thought that was a pretty good deal, that includes Showtime, which I rarely watch, but its there .
  • Like
Reactions: Foxbat
TWiT Tech Podcast Network
· posted in TWiT Tech Podcast Network
0 Replies · 13 views