Social Feed

C
Last reply · posted in DIRECTV General Forum
Last fall i set up my 3 lnb oval dish on my roof with a pole mount and was able to receive all three signals (101 & 110 were in the 90s and the 119 was in the low 70s, but i received all channels fine). Over the last few months, my 119 signal has slowly dissapeared and is now down to zero - I assume this is due to the leaves on the tree growing in.

I went to my roof last week to try and re aim, but nothing for the 119. I moved the set up to all corners of my roof (I have a flat roof, so its pretty easy to get around on it) and no luck. I remounted the dish to its original spot without the mast and was able to get the 101 & 110 with signals in the 90s. So right now i am without the 119 sat.

When I was moving the dish around on my roof, i was able to pick up the 119 signal (in the 90s), but nothing on the 101 &110. It was at a wierd angle, but I had my receiver up there with a little portable TV and i was getting a strong signal from the 119. Its my understanding (And I could be completly wrong) that the 119 sat is lower in the sky than then other two satellites. Is it possible that I was locked onto a wrong satellite and it was registering on the 119 signal meter? Maybe it was from where i positioned the dish, but it looked like it was pointing at a much higher angle than where the original dish was poitning that received the 101 & 110 sats.

Also, I previously bought a Zinwell Multi-Switch (SAM-4803). I have read many post about setting up 2 dishes, but everything I found explains how to set it up using an oval dish to pick up the 110 & 119 sats and a round dish to pick up the 101 sat. Is it possible to use the oval dish to pick up the 101 & 110 and use a separate round dish (with a dual lnb or single lnb?)to pick up the 119?

Any help or suggestions would be greatly appreciated. Thanks!
2 Replies · 1645 views
D
I have the exactly same setup you are describing. I can only get 101 and 110 with my oval dish. 119 is blocked by a tree with my oval dish so I have it coming in on a seperate dish. I have the SAM-6802 switch with FlexPorts so I use a seperate 18 inch dish (either single or dual LNB will work) for 119 and run a single wire to the FlexPort. It works great for me. I also have my 72.5 satellite for local channels on the other FlexPort. You can pick up a new SAM-6802 on eBay for pretty cheap if you want to go that route.

To answer your other question, 119 is lower in the sky than 101 and 110. That is why multi-satellite dishes have the skew. It is possible that you have the dish pointing too far to the west and are picking up 119 on the 101 LNB, for example. If you cover up the 110 and 119 LNBs with aluminum foil (that would be the center one and the one on the far right if you are looking at the dish from the front), then you can be sure that you are getting 101 on the correct LNB. If you have the skew set correctly, 110 and 119 should fall into place. If your 119 still doesn't come in, you most likely have the same problem I have and you could either relocate your oval dish or use a seperate dish for 119 as I explained above.

Hope this helps. Good luck!

-Dan
D
Quick note,

I never ran into this problem until yesterday with 119 being on a FlexPort but if you have a 2 tuner receiver, it will not be able to tune to an even and odd transponder channel at the same time. It makes complete sense and I can't believe I never considered it. For example, if you had 2 recordings set at the same time, one for a program on say, HBO Latino on transponder 30 and one for something on like.. CCTV9 on transponder 27, which ever one tunes first is going to get the signal. All of the high-def channels on 119 are on even transponders though so if that's all you used 119 for, you would be good using a FlexPort. Or if you were using just a standard HD receiver with a single tuner there wouldn't be a problem either.

Just thought I would add that.

-Dan
Scott Greczkowski
Staff member HERE TO HELP YOU! Cutting Edge
Last reply · posted in The Chit Chat Club
Sometimes a thread gets so many posts in it that is can cause issues for the server so that why today we introduce The Song Name Game Part 3!

So let the game continue!

The last song was added by Bobby who posted...

One Meat Ball - Andrews Sisters

CONTINUE ON AND HAVE FUN! WELCOME HOME TO SATELLITEGUYS.US!

Here are the original rules for the game as posted by WebbyDude back in 2006. http://www.satelliteguys.us/threads/68645-Song-Name-Game

Just name a song title and the band who performed it. The next person does the same thing, but needs to list a song title or band name which includes a word from the previous entry. Pick songs from any genre.

Example:

Long Live Rock and Roll -- Rainbow

Rainbow in the Dark -- Dio

Another example:

Ride the Lightning -- Metallica

Lightning Strikes -- Ozzy Osbourne


Get it?


An additional note: we all know that song titles, sometimes, use profane words. Because this is a family friendly website it is advised that you clean up that title up a bit. This is accomplished by using something like sh!t instead of the real word. Thanks....
68565 Replies · 2675573 views
  • Like
Reactions: c-spand
dishstaller
Little Miss Dangerous - Ted Nugent
RaiderPower
Little Miss Can't Be Wrong - Spin Doctors
  • Like
Reactions: FTA4PA
sdfntx
Jump Down, Spin Around - Harry Belafonte
  • Like
Reactions: Bobby
long_time_Dish
Stop Draggin' My Heart Around - Tom Petty and Stevie Nicks
H
This Old HEART Of Mine(Is Weak For You)-The Isley Brothers
iJustine
Last reply · posted in iJustine
1 Replies · 9 views
T
It's not even where it folds!
SuperDish_Fan23
Last reply · posted in DISH Network Support Forum
Why are ViP922s So rare? like its crazy how ebay has none, i checked everywhere, also, i got a ViP222k now, which is actually activated!
20 Replies · 501 views
S
That's not really unusual. Cable companies like to the provide the box too. The phone company provided the phones in until the government forced them to allow third-party phones.
  • Like
Reactions: charlesrshell
Almighty1
That's not really unusual. Cable companies like to the provide the box too. The phone company provided the phones in until the government forced them to allow third-party phones.
Yes, the Western Electric phones that says "Bell System Property, NOT FOR SALE, Western Electric".
AZ.
AZ.
Yes, the Western Electric phones that says "Bell System Property, NOT FOR SALE, Western Electric".
someone is showing their age
Almighty1
someone is showing their age
LOL. It depends if the person saw it during the years when they were actually still available which is 1968 to 1983 meaning the person could be 43-58 years old or they can even be a few years old if they learned to read and write at a young age and actually saw a telephone with that label somewhere recently just like even here in San Francisco, payphone still exist physically in public places but whether they can be used or not is a different issue. It still looks like this even today:
1792633296785.webp
  • Like
Reactions: charlesrshell
dishstaller
I opened my Radio Shack in Sept 1984 and right about that time they did the whole deregulation thing with the phone companies. I bought TONS of those phones that had been refurbished with a new outer shell. You could throw one of those out of a 3 story high window and it would still work.
That was an interesting time in history. I would have older customers come in and ask about phones.....they were terrified that they were going to get into trouble hooking up a second phone without the phone company knowing about it. One of the funniest episodes of WKRP was the one where Johnny thought the cops were showing up because they had an unregistered phone. I guess younger folks can't conceive of a time when you were limited to the number of phones you could have in your house....and limited to the length of the cord 🤣
navychop
someone is showing their age

You should hear his stories about when rocks were soft and pterodactyls were the new kid on the block!
dishstaller
One of the funniest episodes of WKRP was the one where Johnny thought the cops were showing up because they had an unregistered phone.

View: https://www.youtube.com/watch?v=CA0yZ1nrm6M&pp=ygUPd2tycCBwaG9uZSBjb3Bz
dishstaller
Pub Member / Supporter Lifetime Supporter
Last reply · posted in The Chit Chat Club
He was 71 yrs old. One of my favorite songs is Seminole Wind....the violin is killer.


View: https://www.youtube.com/watch?v=W8sh9P3X33w
5 Replies · 45 views
FTA4PA
Rest In Peace
  • Like
Reactions: dishstaller
M
I Wish I Could Have Been There is an amazing song. Rest in peace Mr Anderson.
  • Like
Reactions: dishstaller
Bobby
Rest in peace.
  • Like
Reactions: dishstaller
comfortably_numb
Hope you're out there Swingin', John.
  • Like
Reactions: dishstaller
dishstaller
I Wish I Could Have Been There is an amazing song.
That's one of those songs that hits a little too close to home for me. I like the song but just can't listen to it. It's kinda like that song "Daddy never was the Cadillac kind".....reminds me too much of my Grandfather who died Feb 18, 1995.
N
Last reply · posted in DISH Network Support Forum
My OTA is not working anymore. This started after the latest update. I have the OTA dongle with a OTA antenna that I've been using for years. My hopper does not recognize the dongle anymore and when I go to the OTA setting, it has a screen that says to plug a dongle into the USB. I tried unplugging and plugging back, in the same usb port and other ports. The Hopper does not recognize it. Anyone have same issue?
201 Replies · 5114 views
  • Like
Reactions: charlesrshell
Scott Greczkowski
Did you people having this issue contact Brittany yet? Shes trying to keep track of things and it would be good for you to contact her as maybe she can get this somewhere and get fixed.

Now while unofficial, I am hearing this issue wasn't caused by DISH's software team, but was caused by a chipset driver update that seemes to have hosed some older USB devices. If this is indeed the case I can see why DISH didn't know and why they are slow in fixing it as they need the chipset company to fix its drivers and release them to DISH so they can be pushed out to all.

DISH does not hate you guys nor do they want you to buy new USB dongles. I am rather sure they didn't even know this was an issue until they saw it posted.

Again contact Brittany if you are having this issue, so she has your info and hopefully she can do something for you to keep you happy. :)
bookworm370
Did you people having this issue contact Brittany yet? Shes trying to keep track of things and it would be good for you to contact her as maybe she can get this somewhere and get fixed.

Now while unofficial, I am hearing this issue wasn't caused by DISH's software team, but was caused by a chipset driver update that seemes to have hosed some older USB devices. If this is indeed the case I can see why DISH didn't know and why they are slow in fixing it as they need the chipset company to fix its drivers and release them to DISH so they can be pushed out to all.

DISH does not hate you guys nor do they want you to buy new USB dongles. I am rather sure they didn't even know this was an issue until they saw it posted.

Again contact Brittany if you are having this issue, so she has your info and hopefully she can do something for you to keep you happy. :)
Thanks, but until they do, can't Dish just revert to the old driver that worked? Then test the new driver when delivered,d before pushing it again.

But then what does an old CIO know! I've only reamed quite a few buttholes from my people that didn't do that! ;)
S
Thanks, but until they do, can't Dish just revert to the old driver that worked? Then test the new driver when delivered,d before pushing it again.

But then what does an old CIO know! I've only reamed quite a few buttholes from my people that didn't do that! ;)
dish can't revert back to older drivers or updates. although just one reason not to buy the ota dongle!!!
  • Like
Reactions: charlesrshell
ppappas
dish can't revert back to older drivers or updates. although just one reason not to buy the ota dongle!!!
They can absolutely put the old driver back if they wanted. This is an embedded software environment in which they have total control. All they have to do if build a new version of firmware with the old OTA driver and test it of course. They just don't want to spend the resources doing so. If they are not going to continue supporting the single tuner adapter, then they have to say so.
Almighty1
They can absolutely put the old driver back if they wanted. This is an embedded software environment in which they have total control. All they have to do if build a new version of firmware with the old OTA driver and test it of course. They just don't want to spend the resources doing so. If they are not going to continue supporting the single tuner adapter, then they have to say so.
Unless of course they didn't keep a copy of the old drivers and can no longer get it. Then there is always the their support for the product is EOL after a x amount of time so it will make the consumer have to buy the current product offering.
B
Anyone heard any updates on this, I'm still having the issue so thought I'd check in.
  • Like
Reactions: charlesrshell
Almighty1
Anyone heard any updates on this, I'm still having the issue so thought I'd check in.
No updates but if you can get DISH Technical Operations to roll you back to H710 or earlier even though H708 would be best because it also eliminates another problem like in this comment, you will also no longer have the problem as long as you don't update manually or forced to any new version until the problem is fixed as the problem started in H711 and still exist in H712 and H713.
  • Like
Reactions: charlesrshell
dishstaller
Installed an off-air antenna a couple days ago for a customer who had just cancelled his Dish service. He had a dual off-air adapter and gave it to me. Cool. I'll keep it on the truck....might come in handy. Got to admit I don't watch anything as far as live tv goes anymore. Even if we have severe weather, our local channels will have a live feed on Youtube.
navychop
In other news, it was announced that the software fix for the two tin cans and a string will not be forthcoming. A hardware fix is required. However, that fix will let you receive stations from a gazillion miles away.

Truck roll charges may apply. Two year commitment required.
M
Last reply · posted in Over the Air Television By RabbitEars.Info
Interesting article about the work being done to develope an ATSC 3 converter box. Yes it does mention affordable.
6 Replies · 218 views
navychop
DEATH TO NEXGEN!
TRG
TRG
17 years ago the US turned off analog OTA signals in favor of digital broadcasting. Now the push is ATSC 3 "Nextgen TV". But nobody seems to be able to agree on DRM implementation protocols. People don't want to hook their TV up to the internet in order to watch over the air TV. At least I don't. With all the data they collect about your viewing habits the box should be given away at no cost.
navychop
Comb your hair.
primestar31
DEATH TO NEXGEN!
star trek GIF


It's dead, they just don't know it yet. They killed it by forcing DRM on it, and that TOTALLY botched implementing it.

There is absolutely NO compelling reason for anybody to switch to ATSC3.0. They only want it as a total and complete money grab.
  • Like
Reactions: FTA4PA and navychop
navychop
I truly hope you are right.
  • Like
Reactions: FTA4PA