This may take a while. . . hopefully before fall.
Set up is:
DISEqC HH DM910 42mm mount/motor
Invacom Quad Polar Legacy 4 O/P lnb
CaptiveWorks CW-41, CW-600S Premium
Winegard DS-2076 toroidal 76cm
all mounted to side of house.
Some things that I think are wrong:
The manual screen shot has Quality below Signal but the unit has Quality above Signal. minor
I haven't found a procedure to manually add a channel. minor
The disk that came with the STB has a CW Premium folder but the serial program did not work. I had to download a newer one. major
The .sdx format that CW claims is not the same as SatcoDX. major
I have loaded an .sdx file after back and forth creations with Channel Master opening first an .sdp file. This file failed to add anything and made the screen pale.
I am scared to download data as a binary. What will it do?
The upload data file is only 10kb. This must be fruitless.
The Conexant STB editor is weak. Period.
The SatcoDX client software won't connect to the CW Premium even though this is an option in the STB. major
If anyone can answer some of these riddles I would like it.
~~~~~~~~~~~~~~~~~~~~~~
~~~~~~~~~~~~~~~~~~~~~~
I stopped working on the polar mount after following procedures like "FTA Reciever Testing Manual" by Dipper. I am getting signal as strong as 75 but nothing on Quality. I was connected through DISEqC switch 4 in 1 on LNB1 but have removed it to trouble shoot. The quad LNB has two Linear and two Circular. I am using Linear for Ku band at a Local Oscillator frequency of 10750.
I am located at latitude 35N (close to 36) and Longitude 086W. I am fine tuning on AMC 3 (87W) which is 181.15 True South. The elevation is 48. The offset is 24. Expected Measured is 113.84. The math is: 113.84 - 90.0 = 23.84 23.84 + 24.47 = 48.31
I've got no channels and no Quality. What do I do?
Set up is:
DISEqC HH DM910 42mm mount/motor
Invacom Quad Polar Legacy 4 O/P lnb
CaptiveWorks CW-41, CW-600S Premium
Winegard DS-2076 toroidal 76cm
all mounted to side of house.
Some things that I think are wrong:
The manual screen shot has Quality below Signal but the unit has Quality above Signal. minor
I haven't found a procedure to manually add a channel. minor
The disk that came with the STB has a CW Premium folder but the serial program did not work. I had to download a newer one. major
The .sdx format that CW claims is not the same as SatcoDX. major
I have loaded an .sdx file after back and forth creations with Channel Master opening first an .sdp file. This file failed to add anything and made the screen pale.
I am scared to download data as a binary. What will it do?
The upload data file is only 10kb. This must be fruitless.
The Conexant STB editor is weak. Period.
The SatcoDX client software won't connect to the CW Premium even though this is an option in the STB. major
If anyone can answer some of these riddles I would like it.
~~~~~~~~~~~~~~~~~~~~~~
~~~~~~~~~~~~~~~~~~~~~~
I stopped working on the polar mount after following procedures like "FTA Reciever Testing Manual" by Dipper. I am getting signal as strong as 75 but nothing on Quality. I was connected through DISEqC switch 4 in 1 on LNB1 but have removed it to trouble shoot. The quad LNB has two Linear and two Circular. I am using Linear for Ku band at a Local Oscillator frequency of 10750.
I am located at latitude 35N (close to 36) and Longitude 086W. I am fine tuning on AMC 3 (87W) which is 181.15 True South. The elevation is 48. The offset is 24. Expected Measured is 113.84. The math is: 113.84 - 90.0 = 23.84 23.84 + 24.47 = 48.31
I've got no channels and no Quality. What do I do?