Recent content by kooguy

Got my 2nd 4x4 Zinwell multiswitch yesterday, that resolve my signal issue on all my receivers. Stay with Zinwell hardware!

I always take precaution when handling the switches and Diseqc, power off all my receivers (including unhooked the power cord), follow some good advice from this board. So could be my 2x1 Diseqc not able to handle the load when using that many LNBs. Compression connectors - I have the tools, so...

Thanks for tips... What type of connections (crimp, compression, screw-on)? Cripm, all RG6 Signal issues - Zero signal all transponders. Are the LNBFs standard or universal type? Standard LNBFs, all dual output Receivers : 2x Micro HD, 1xOpenBox S9 97W - 36" dish (Focus brand LNB) 95W - 31"...

I have 4 dishes pointing 97w, 95w, 87w, 83w and connected to 3 receivers, using two 4x4 multiswitch (Zinwell and Digiwave), three 2x1 Diseqc. Two of my receivers having cable length more than 75ft and having signal issues with some satellites. I'm not sure any non-power switches out there can...

Once I got the clarification over the phone order...I just ordered the units, the discount alone offset shipping charges for Canadian! Heck, my Openbox cost more than that micoHD, not to mention without any future support (knock wood it doesn't break down tomorrow) down the road. For that...

Once I got the clarification over the phone order...I just ordered the units, the discount alone offset shipping charges for Canadian! Heck, my Openbox cost more that micoHD, not to mention without any future support (knock wood it doesn't break down tomorrow) down the road. I don't like to...

Thank you! All good, just ordered two units over the phone...

Talked to Megan, Canadian Paypal not accepted. Tried order two units online using credit card. On checkout, I don't see $40CA discount, only $29.00? Also, shipping option is FedFx which has a history of being notorious to 'dink' Canadian with additional 'admin' fees later. Any assurance...

This is more for SatelliteAV... For our Canadian friends, please call our office before 4pm, June 29th and we will offer you a $20CA discount on the first units that will ship from our Canadian distribution partner (around the 2nd week of July, 2012). Really interested in this unit, if I order...

Nerver mind...I figured out the issue. Just a little tricky to set this box up.

The switches are Zinwell (4x4, 2x1) and they are working properly with other receivers other than this Nfusion unit. I must have missed something obvious...Just can't be that difficult to set it up.

Hi all, I have 3 dishes, one point at 97W, one point at 95W and one point at 101W, all joined via multi-switch and connected to three receivers - ViewSat ultra, Captive Works (CW-700S), VisionSAT IV-200. All receivers are able to get signals properly, no issues at all. Here is my current...

I am a newbie and been through your situation...I'll do my best to describe the procedure. Make sure, 1. The mast must be stable. It should not tilt with the dish on it. 2. The mast must be 100% plumb. Put a level on top of the mast ensure all side are 100% level! This step is very critical...

Just checked...Same as before. VisionSat settings for 95W and 97W 95W 97W LNB Power : On On LNB Type : Single Single LNB Frequency: 10750 10750...

ok..I tried the 2x4 switch approach. I used the 3dish3fta diagram from http://www.satelliteguys.us/fta-mpeg2-faqs/134124-switch-setups-simplified.html#post1344314 Just for testing, I only hookup the problematic VisionSat receiver using two 3x4 Zinwell switches and one 2x1 DiseqC. Before I...