Recent content by jackpeas

  • WELCOME TO THE NEW SERVER!

    If you are seeing this you are on our new server WELCOME HOME!

    While the new server is online Scott is still working on the backend including the cachine. But the site is usable while the work is being completes!

    Thank you for your patience and again WELCOME HOME!

    CLICK THE X IN THE TOP RIGHT CORNER OF THE BOX TO DISMISS THIS MESSAGE
  1. J

    primestar dish need help getting on the satellite arc

    primestar dish need help getting on the arc Thank George,I am standing flat on the garage roof by the pole.105,103,101,99,97,95 got about 20 and above quality.I have notice as i come down from sat 105 to g3c ku quality run thru these sats.But it stop at G3/that could mean I am too far down...
  2. J

    primestar dish need help getting on the satellite arc

    primestar dish and hh motor help Thank you.I went out monday and tried to get more quality on g3 ku but made it /no luck. think I am lost.Please give more advice
  3. J

    primestar dish need help getting on the satellite arc

    primestar dish tring to get on the arc. Hi thanks guys,back in February I had DN to install a dn system .He put the dish on the north side of my garage and my pole is on the south side.He have the dish on the edge and its about center on the north side.Its not in the center or middle of the...
  4. J

    primestar dish need help getting on the satellite arc

    Hi I am jackpeas tring to get on the sat arc.Amc3(k3) @87 degree is my southmost sat.My lat is 41.6,my longt is 87.6,and dish is 23.5. My neighboor has a tree limb blocking me.Their are garrages,so I had to raise my dish about 14 ft to see over it.Last year I got amc3,But I change my pole.Now I...
  5. J

    Noob needs help equipement

    What do you mean about motor elevation PBS? :up
  6. J

    Primestar Dish on SG2100 ?

    primestar and new stab 120 hh motor No I did not/just added some 2"pvc pipe for shim. But having problems.I just now see these post about the sg 2100 hh motor. And how to make it liter.I am tring to find my elevation/Sadoun site say 23.5,pansat book say 24.When I used satfinder it say 41.8. So...
  7. J

    Primestar Dish on SG2100 ?

    Had my primestar 30"x40 on my sg 2100 Hi I am jackpeas@yahoo.com in chicago,ILL.I had my primestar on a sg 2100 hh motor.But it was to heavy.Now I have a stab 120 hh motor.
  8. J

    DS you are not useding HF splitters

    Hi guys,I am jackpeas in Chicago,ILL.I have a 3500 pansat and satwork 3688 fta receiver,2 pci cards,2/4dtv.I am useding 2 HF(4 to1) splitters 1 for c-band and 1 for ku.Now I have a pansat(4 lnb) 2c&2ku feed.That I am planning to replace with a new coroto plus to day.I have 2 hh motors.I got a...
  9. J

    Using Primestar dish and lnbf to get 105

    I have the heavy 30"x40" primestar dish Hi and Hello,I am jackpeas@yahoo.com in Chicago,ILL 60643.I got my primestar off ebay.I got a phase 3 lnb on it. but it in the garrage.Its has the H V lnb can on it.I put a 1/2"electric pipe around the front and sides.For 6 or 7 lnb.I also have a...
  10. J

    focal length?

    Skyvision has a guide in they catalog. Hi I am jackpeas in Chicago.I get a catalog from skyvision.Its got the guide inside.I am having the same problems polarity.I had this problem back in march 17 2005.I for got what i did to correct it.See I have total of 5 inside the house now.With a pansat...
  11. J

    actuator arm

    Actuator arm to far west about 400 click on a 24" arm HI I am jackpeas,My 36'' venture just stop and i replace it with a 24" arm.Now the clamp was about 10" from the end.I was comming up short on the east end.Now I move the clamp to about 2" from the end of the shaft.I am getting about 400...
  12. J

    feed horn troubles

    The feed I am going to put back on is working.I look in side at the probe it was turning 90 deg.So I adjusted it with my 4dtv.When i did a master reset.I went to opt 642 I think/where you set up your lnb to c band and ku lnb/not cband and ku lnbf.Now since you said about the probe/yes it move...
  13. J

    feed horn troubles

    Hold on not so fast/Dont go buy untill you check everything Hi i am jackpeas@yahoo.com in Chicago,ILL.I got 1 pansat and adl 2c &2ku feed(4 lnb)4 x120'ft of cables,2 multi-switchs.I started having problems with my adl 2c 2ku with no servo motor in.I change out the 2 cband lnb and 2 cables.Still...
  14. J

    Plug for Lee Richardson of Mech Tech

    LEE Richardson is top shelf HI I am jackpeas@yahoo.com in Chicago,ILL.You know you keep your best stuff on the top shelf.You have to reconize quality when you see it or hear it.LEE is a quality man.He is the same everyday.But I still shop around/Looking for the best price.We had a search for...
  15. J

    adding ku to cband dish

    Where do you get the replacement circular lnb I did not see where he said how he got the lnb bell to go in the drill hole.Well I cut mine off and put the plastic ring that came with the old one on the new one.Where do I get a new lnb for the dbs lnb in the scalar ring?I dont need the scalar...
See more
Top
Back