Search results for query: *

I used to live just about 2 miles west of that zip code, and the info came from Satellite dish look angle pointer calculator, I used my old settings as a reference for pmow to get a start on his quest for setting up his dish and motor.

Motor Elevation: 33.53 Dish Elevation: 24.55 True Azimuth: 117.7 Magn. Azimuth: 104.83

I used a Hose clamp, put the thread area of the clamp toward true south, and the motor bracket would rest on the clamp. I loosened the nuts just enough to allow some rotational movement of the whole assembly and the hose clamp kept the motor from sliding down the pole.

Side arm length is 100cm ( 39 3/8" ) and the bottom one is 72cm ( 28 3/8" ) measuring from the face of the dish.

How about a polar mount for 120cm offset and prime focus dishes using an 18 inch actuator (if possible)? that is something I sure could use.

Thanks for the info, I will use the volume knob and keep the tone sound down to a mild roar, but thanks again for the information.

Question on the firmware, which is better, the factory or the other? say for adding and editing sats, channels and pids?

Hey Thanks clearing that up for me, I was wondering big time.

I just acquired a Coolsat 8000 HD, and my question is does the optical cable have to connected to a Dolby 5.1 Surround system to get the use of the AC3 audio, or can I get AC3 audio with the RCA connectors connected to the TV and or the stereo system?

I used a 24 volt DC battery charger to test my actuator, it just ran slower that normal.

I am curious, with all the negatives being posted about this service, are all of the naysayers NOT going to use the service if it gets up and going? I have started 2 business in my past and both of them took longer than planned for to get up and running, and a slow economy makes for a tough...

You can take a look at this site, it may do the trick for you. C-band Satellite Installation

Maybe an AZBox ultra could be a good start.

Lots of Russian, Indian, Chinese, and just plain foreign channels all over the place, does anybody know what is going on with Dish? I didn't change my programing, and I really don't want to get smoke blown up my ------ by calling them, no changes here, my A&E channel is blank and 119 seem to be...

If you are talking about using an H-H motor (SG2100 type) Try connecting a cable from your receiver to your motor, then a cable from your lnb connector on your motor to a 4 port Diseqc switch, then port 1 to your lnb on the motorized dish. Ports 2 and 3 to the lnb's on your stationary dish

your going to need a C Band setup to get Univision these days.

loosen the motor clamps on your pole and rotate your motor and dish assembly 2 or 3 degrees to the east.

Southern Oregon TP 12060 71% signal and 00 Quality, it worked yesterday morning though.

Yes, using the WiFi calculations will allow you to get the off set focal point, and your welcome.

That's nice, pretty much the same as "diameter squared divided by 16 times depth = focal length". Also you may want to give this program a try: Parabola Calculator version 2.0

Try Badcaps.net - Badcaps Home

Lak7 Thank you for the info, I couldn't remember where it went, I was running out of positions and the rain clouds are heading back my way.

I have a BSC621 and I am wondering if anyone knows where to top of the LNB is? It has a little triangle on the body, so where would that be in reference to say to horizon?

I picked up a working Strong MiniSat receiver and I can't find any information about them on the net, does any one have and tips trick and or information about this box? editing software upgrades and the like?

Go into USALS and on the phantom satellite change the position to 124.9w, that's worked for my VSU2K.