Search results for query: *

All the Moteck /Strong and other named V-boxes I have seen , were provided with 2 secundairy voltages , for 12 v and 36 v Sometimes there is a temperature fuse under the isolation , maybe switched off .

That reedswitch is not original , maybe its not in the right place .

Hi ftaseek , I have more of it . Have to find out the postal costs , where do you live (PM ?)

With a optical sensor , the making of a pulswheel is far more easier (I think) This one was made for a AHM36 H2H rotor to let it work for Usals .

After a good look I think you'r right on the picture the opposit spanner hole is covered by the shaft end .

since that light colored bearing securing device is not secured by the bolt , holding the motor to the pipe , it might be possible to push the thinner pipe out by stamping it vertical on a solid wooden block

I never tried . I dont know why there are 3 more magnets , reference point ?

There are indead some SG2100 types with just fixed mechanic end stops . The STAB uses reedswitches activated by magnets in the half wormwheel

RimaNTSS , does this one also has a different openings angle ?

Looks like a Prodelin dish , about the lnb position , see the pict. of my 890 @ Ken2400 can you show a full picture of the backside ?

I think its a ten turn pot , attaching the pulswheel direct to the threaded shaft will bring more pulses / inch actuator movement .

Love to see those pictures

Since searching for a HN9200 ka lnb did'nt help , I post the request again . To make a more universal lnb ( H/V - RHC/LHC ) by rotating that HN9200 its more suitable than the Direct SL3K lnb that I already have .

The use of that 80:1 ratio of the new gearbox causes the half arc with a V-box . What kind of pulser is under the hood of the original motor ? Any pictures ?

Can you show us a picture from the front and backside ? Its a strange positioner , I dont see relais for E / W , probably the 2 transistors do the job . The two red wires from the connector at the circuitboard are both connected to contact 1 at the backside and at contact 2 is a wire straight...

Old picture of C- circ / C-lin / KaKu combi / Ku lin / Ku circ / SL3K at 1.8 m Channelmaster Now also a modded Ku lnb attached for EsHail 25.5º E (10.300 - 10.700 Mhz)

I've learned a lot from his answers and had my profit off it. I wont say EOL(end of life) they still goes on , more EOP (End Of Production) Thanks Titanium Satellite !

You can drill a 4 mm hole in the part you're holding and use a longer shaft . I dont know about the postal costs from the Netherlands but I can send you that part ( the part will be for free) It will fit in a envelope

In the SMR 1224 is no electronic circuit , just a reed switch and two end switches each bridged by a diode just like the inside of a actuator .

four separate magnets

I think the + 12 v connector is for the use of a 12 V switch , use to set on or of in the setup menu . Better start with the +6 V for the optical sensor .

For sure its no CM feedarm and lnb holder .

kdjuan is linking to this lnb . Unknown what receiver he is using . LOF setting for a Universal lnb are 9.750 / 10.600 22khz off 13 / 18 band

Here in Europe we have for lineair signals UNIVERSAL DUO lnb's for 19.2 and 23.5 E for 60 cm and other ones for 80 cm offset dishes Also TRIPLE versions for 19.2 and 23.5 and 28.5 E

The link shows ist a universal type , so 9.750 / 10.600