Search results for query: *

I opened the box and checked everything under a 10X microscope. I was surprised to see some of the solder connection show what looked somewhat like a cold solder joint. I don't think they are the problem. I also checked the little fingers to make sure they are contacting the plug. I purchased a...

I am planning on doing just that. The firmware is most recent, Thank you much, that would save a lot of headaches! From what I understand the composit output is not controled by the firmware, and that redoing it would to be to no effect. If anyone knows diffrent let me know. At this point I am...

HEY CHARLIE, Thank you for taking the time to walk me thru the key by key plays! I may end up giving this a try. My tv never had HDMI so i purchased a 3.5 mm composit to 3 RCA . It worked fine with that, now it will only work with the HDMI. never tried that untill today. So... yes it works with...

When I was having all of the issues when I first purchased it I ended up installing, ( I believe this is the update I installed), the latest firmware and doing a factory reset. I suppose it would not hurt to do it all over again. I will have to borrow my Daughter's TV to be able to use the on...

Thank you, I know what the ends look like. I was not sure of the two cables which to use...anyways I went to my Daughter's house, she has a HDMI TV. I used the straight thru cable and it works on HDMI. I have screen output. I don't recall any settings to select on the MicroHd menu to select...

Primestar that thought had already crossed my mind. When I origionally purchased this I tossed the HDMI cable into a box of other cables. I retreived two of them from the box one is straight thru cable and the other has a little round barrel about 6 inches from each end. Not sure of which one to...

I gave all of that several tries.

I would love to be able to do that. That would indicate that I could see the screen and I would have no problem. I presume you meant the MicroHD.

No, it acts as it always did only one start up cycle. I just have no output to the TV.

I purchased a new microHD on sept 20th 2013 I had some issues with it, but they were resolved with downloading program. It has worked perfectly for me until a couple of days past. When I use the remote to turn it on the little green lite comes on for a short time then switches to red for a few...

If you have nothing good to say, say nothing at all. Primestar31, This is not the place for that type of comment…you are out of line!!! If you want to PM me, do so; if not be silent! Sam

richyrich, I really enjoyed your post...there for an instant you took me back to my youth as your post is reminiscent of the flower children of the sixties, minus all the talk of love, piece and war. Sam

Results from Sat av california Gen. Man. Eugene Hello every one, I spoke with Eugene from SatAv. Yesterday he had me do one last thing and I reported back to him today with the results. That last thing was a factory reset with a power down. Everything seems to be functioning fine currently...

A Raine, That does sound like what happened to me! Hope that is the case and not something deep rooted. I appreciate your post as it has helped put my concerns a little more to rest...Thank you, Sam

Thank you I will. If only I could be sure it is all sorted out. I am hoping to hear more from sat av gen. manager Eugene as to his thoughts of all that happened between turning it off last evening and getting it back up later today. It is a little premature to be certain, however it appears...

Update to dead in the water. I called the boys in California and spoke with the General Manager, Eugene, who seemed very knowledgeable, Professional and helpful. He had me retrive information for him and try diffrent things...to no avail the final request was to do a factory reset, disconnect...

Yes I installed it, First off I had problems moving the dish, only to find out that the Dynosat receiver had a weak power section and did not have enough output to properly move the dish. That is when I purchased the S-10. Once sorry If I confused you.

Primesrar31, I am sorry if you are confused by my responses. I am doing my best to do all of the things that are suggested by you guys and I do appreciate the help. I realize that being said I posted a confusing list of specs fot the lnb. unfornitally that was not the lnb that was in the system...

No, It did not move to 97w. Was still on 83w , I AM POSITVE OF THAT. No, I did not try to wiew channels on 97w because that would be to no avail, if the dish would not move. Thank you for your reply, Sam

All was lost before I tried the new lnb, The only reason that I tried it at that point was to be sure the old lnb was not the problem. The old lnb was set to 10750 the only freq. it would function at and the only one listed on the tag. I finally went in and reset it again to 10750 checked all...

All was lost before I tried the new lnb, The only reason that I tried it at that point was to be sure the old lnb was not the problem. The old lnb was set to 10750 the only freq. it would function at and the only one listed on the tag. I finally went in and reset it again to 10750 checked all...

All channels lost on 83w. Last night i was watching TUFE and turned it off about 10:30 p.m. everything was fine. Today I received in the mail my new GEOSATpro SL1PLL LNB. I wanted to try it to see if it helped with the blind scan of 83w. Turned things on and got no signal. That surprised me as...

83w tp and other info I tuned to channels, displayed picture good. Pressed info button twice. Here is the TP's all 3 (1135/H/4439) Other info for RTVE: PID V33/A34/P33 FEC 3/4 SID 1 TUFE: PID V36/A37/P36 FEC 3/4 SID 2 PBJE: PID V39/A40/P39 FEC 3/4 SID 3. Hope this is what you...