Search results for query: *

I am considering moving from the Madison, WI area to the Tomahawk, WI area and was going to take my dish equipment which I own with me and reinstall it there. I currently have two dishes on my roof pointed at three satellites, 119, 110 and 61.5. If I reinstall this equipment would I be able to...

IT WORKS! I think the problem was the F connector on the coax from the power inserter. I redid all of the F connectors anyway and after resolving some reciever issues, they had to be rest, everything works. Thanks again for all of the help. Later Andy

Thanks for the replies everyone. Unfortunately it was thunderstorming all afternoon today and I didn't want to get up on the roof in that. I should be able to try it tomorrow. Thanks Andy

The copper center of my cables do not extend beyond the end of the connector. Do you they need to extremely long in order to function properly? I hate to have to redo all of the connectors. Thanks Andy

Thanks for the reply. I will keep my fingers crossed that it works. I did not have receiver one connected to the power supply in my previous attempts to connect the system. I guess the 5 years in school becoming an Engineer paid off in drawing that diagram! Thanks Andy

Here is a diagram of how I think I should connect the switch based on the previous post. Is this correct? If it is I will try again tomorrow. Thanks Andy

I was looking at the power supply for the DPP44 and have a question. There are two coax connections coming from the power supply. One is labeled to go to the switch receiver 1 position for powering the switch. The other says to go to the receiver in. Do I need to have one of my receivers...

I have the specific seperator used for the 622 receivers to split the feed for the dual tuner.

I verified which port 1 and port 2 from the DPP Twin are near the switch. Now that I know which one is which the DPP44 Switch doesn't work. Any Help?

In an attempt to try and figure this out I have removed the feed from the 129 LNB and only have the port 1 and port 2 of the DPP Twin connected to the switch to see if my 129 feed is screwing it up for some reason. I still have no signal to my receivers through the switch. Since I do not know...

Well I finally got around to running another RG-6 coax from the dish down to my basement. It was actually easier than I thought it was going to be. However now I cannot get any reciever to see a signal after the switch. I have it wired as followed. I don't actually know which cable is...

Thanks for the info. Unfortunately this is going to be extremely difficult for me to do. I cannot run the cable down the same route as the other cables as it runs down inside my chimmeny box. I really don't want to run the cable around the outside of the house either. I guess I might have to...

I have been unplugging the switch every time I make a change. Where should I connect the ground to the switch? I have a ground cable near the switch I am just not sure where to attach it. They way it is wired coming from the roof is as follows. There are only two coax cables coming out of...

I actually just got off the roof to see exactly what was up there. I have a Dish 1000 with a single 129 DP LNB and a Twin 110, 119 DP LNB.

I just finished trying that and it did not work. I was able to complete the check switch when I bipased the 44 switch to the receiver and then once I went through the switch again nothing. Any other ideas? Thanks Andy

I just purchased and installed a DPP44 switch so I could hookup a third 622 to my third HD tv. I have the single smaller dish on the roof that originaly fed directly to my two 622s. Now that I added the DPP44 Switch I cannot get any signal to any receivers. I have checked my connections over...

Is there a difference between a DP44 and a DPP44?

I just checked and I do have the L4.03 software version. I am starting to get sick of having Dish. Any idea as to when Dish plans on fixing this problem? My guess is if I called Customer No Service they wouldn't know. Is there any way to revert back to an old version of the software?

I currently have 2 622s that are hooked into my roof antenna for my HD OTA programming. About a week or so ago I started having problems with both 622s dropping the OTA signal. Every couple of minutes I loose the signal and get the yellow pop up or it pixelates and pauses for a second and...

I currently have two 622 recievers in the house. I called to add a third 622 and they placed my order as a lease. Once the techs showed up today they informed me that dish will not allow 3 622s on the same account. I have three HD TVs and I need to keep the 2 622s I have, I can't stand...

I just noticed this same problem over the past few weeks with my 622 reciever. My signal strength is at 100 with no preamp. It was never a problem until recently. Does anyone know what Dish Network has done that caused this problem?

I currently have one 622 hooked up to a tv and the OTA stations have signal strengths in the high 90's. My local installer added another 622 for my new tv today and the OTA signal strength is in the 70s for that receiver and is so weak that I only get about a third of the channels that I get on...

Well I removed all of the components of the preamp from my system. All of the channels are great except channel 27.1 on freq 26. Below is a list of the signal strengths without the preamp. Channel......Freq.....Signal Strength 3.1 ............50 ......98-100 15.1 ..........19 ......98-100...

I left the preamp on the antenna that is on the roof inline, but I did remove the preamp control box.

Without the preamp my signal strength is in the 60s for all the channels if they come in at all. The preamp set at the minimum level gives me great signal strength across all the channels except the one in question. Channel......Freq... Signal Strength at Max Setting ...... Signal Strength...