Search results for query: *

And does 111 still carry all the HD channels going to in the 70's here and would like to fix my HD while the weather is nice. Thanks

OK it must be aiming because the winds in Raleigh today were gusting pretty high, I switched over to channel 700 and the signal was all of a sudden coming in between 30-60 and when I tuned to the channel it was coming in and going out, so I need to adjust yet again, thanks for all the...

I have done the manual tune thing on a HD channel for hours this is after I get a signal of 97 on a SD channel like 252 or 299! What is the "22khz box should move to "on"" where do I see that?

On channel 252 I get the Movie Channel so I guess advanced lineup on my guide CITY HD is channel 304

Here is what that page shows Coding Mode 3/4 *1 Symbol Rate 19.51 Fequency 1746.250 EMM 4128 Modulation QPSK Multiplex Comb Polarity l_H 22KHZ Tone OFF It is marked OFF

Yes I have a account I get all the SD channels not the HD ones on the 2nd sat.

OK here is all my info : 1. Receiver is a brand new 600 2. 75CM dish - LNB is a xKu LNBF for use with a 75E dish only 3. Map Status - 551-4323:Complete 4. SignalT1(252):97, (Ecb/No:8.9dB) 5. I covered SAT A and lost signal on channel 252 after pointing the dish 6. I change the channel to...

I get I get SignalT1 (252):97, Ecb/No:8.9 db) the same as you. I have mine set at 119 at the back of the dish already

Also when I cover SAT A I lose all signal on channel 252 is this is correct ?

OK it is finally nice here so I am trying to get my Shaw HD channels here in Raleigh, NC I get a 97 signal on channel 252 but 0 on 700 or 300. I have been fooling around with this for 3 hours :( 1. According to dishpointer my skew for Directv should be 62 for my 5 LNB dish and for Shaw it...

So what should the mapping be for this LNB ??

Thanks tomorrow I will move the dish slightly left and see if that helps.

Can either LNB receive either satellite ? Just wondering if say the LNB on the left is for F2 and I have it on F1 and that is why I am getting a great signal on F1 and nothing on F2. Is this possible or will a LNB only get the sat. it is made for

Shaw redid the v-code twice so that is not it, I used one cable for dish alignment and I use another for watching TV so I doubt both are bad since I get the channels on the other Satellite, it could be 1 or 4 but shaw did not say it was alignment and I get a signal of 97 on on channel 111 and...

I called Shaw they said F2 was "missing" no voltage is coming from it and I need a new LNB ? I called the broker he said he has never heard of this at all.

I called my broker, he basically refused to call Shaw and change the V-Code so we reset the box etc etc, we checked channel 700 and then 300 no go on either, then he said to switch to a different HD channel, I get channel 302 - signal strength of 90 - and maybe one or two others, he said I was...

He says it is correct because the "MAP STATUS - 551-4323 : Complete" is this right ?

Finally went to 60% at 35 minutes man this is slow.

Mine looks stuck it has been at 57% and it is at 33 minutes.

Mine is the 1st one non stacked

Thanks I will have them do that and let you know, thanks for your quick reply I could of been out there another 4 hours messing with the skew.

-non-stacked...this is the "quad" LNB...the one with 4 outputs is theone I have I think, the output Freq. is 950-2150 (Non-Stacked)

I have a 600 receiver what is a V code ?

And I miss my Canadian TV, one Olympics done by NBC was enough. I have a 75cm dish. Anyway I set it up and on some channels all is good for example on channel 111 TSN SD my signal strength is 97, on some SD channels it is 0 like channel 67 I get no HD signal at all I have re skewed the...

And I miss my Canadian TV, one Olympics done by NBC was enough. Anyway I set it up and on some channels all is good for example on channel 111 TSN SD my signal strength is 97, on some SD channels it is 0 like channel 67 I get no HD signal at all I have re skewed the dish all the heck and...