Search results for query: *

Want the manual for the Orbitron SX-12 spinmount. I used a homemade bubble level and protractor to align mine perfectly the first time.

I use a hockey puck cut down on a lathe to fit the inside of the scaler ring, careful though I have non Chaparral Lnb's and there diameter is different, not a standard inside measurement, with a 1/4 inch center hole drilled in puck on the lathe as well and a straight fiberglass tent pole section...

Cheap V-BOX III Contacts: One other thing I'd like to mention is I have never seen such CHEAP SPRING LOADED CONTACTS that are on the back of my V-BOX III. I have twice lost the spring in 2 of the contacts and spent a couple of hours trying to to get the springs back in these extremely poorly...

V-box III's move the actuator using the DiSEqC 1.2 commands in the satellite box's menu usually under motor control , I don't think any of the v-boxes use the USALS commands to move the BUD actuator however there are small BUD type actuators that use the usals commands to move a smaller dish...

Your true south setting is off very slightly, 1/16 inch of pipe diameter is a very large move. Very little steps to fine tune. Best tune for me was to align the true south satellite and tune in a Ku digital channel at .3 degree's off of true south and set dish at .3 degrees off with actuator...

Setting focal point This may have nothing to do with anything, my newly received Orbitron manual places the focal point for my SX-12 dish at 50 and 1/8th inch, measured from the dish surface to the scaler ring face and F/D ratio of .36. The dish formula places the focal point of this same dish...

Declination For this type mount, the declination is supposed to be a painted mark on the mount ring pipe, now long gone to the degree tape on the mount pipe. The declination is right when the dish points lower than the mount, which would place the longer 16 inch measurement to the top when all...

Orbitron Yes the 12 footer was motorized at previous location, the 6 ft Andrews is a prime focus dish from the old cable company, the Orbitron came with an 18 inch lite duty Von-Wiese and I upgraded to a 24 heavy duty, when I took it out I marked it but it was not assembled properly at previous...

The original setup manual would be nice as there is no marks on this thing except for the measurements I've taken. The mount came to me with the 16 inch side up and really didn't work worth a crap. Just to know for sure which measurement is to go to the top, 14 or 16 inch as the 15 inch...

Does anyone have the setup instructions for an Orbitron dish mount in the picture, original dish was destroyed in 100+mph wind, original dish was a 12 footer. The mount is straight as far as I know. The large ring has a welded pipe that is off center from top to bottom by 14 inches from pipe...

Yah I found out why you can't, I hooked up a 3-wire jumger from analog to pansat skew control and even with the pansat off the skew alternated from one box to the other giving a real crappy picture because it never stopped trying to setup the polarity. remove wire great picture If I want outdoor...

Ok from diagram the c-band splits to both box's, where do the skew control wires go to analog reciever or digital reciever or to both boxes, into pansat and back out to the GI 4730a so that both can control the servo on the corotor as needed to get a picture on both even and odd transponders or...

Skew line comes in to analog box only at this time , rg6 goes pansat, then out to Gi4730. pansat on, analog G10 tps16,18,19 all with picture. 16 locked sound when channel code rolled analog box tps 16,18, pansat gets outdoor digital G0-1 outdoor channel, analog tps 19 pansat no picture on...

Parts 12 ft bud pansat 2500a GI-4730a c-band lnb Nexus 45k - 65 db ku lnb norsat .7 - 56 db Corotor with servo Routing c-band rg6 lnb to pansat 2500a then out to analog reciever ku band not hooked up ( YET ) My question is should the skew controls from corotor go to the pansat...