Social Feed

R
Last reply · posted in Free To Air (FTA) Discussion
I am getting started in the FTA world and have some questions about the dish install since I have never done a motorized dish. I just received my 3ABN 90cm dish and it seems like very good quality. The dish mounting bracked is stamped Azure Shine and I particularly like the fact that the LNB mount is located by 3 arms bolted to the rim of the dish. It seems the LNB can never be out of alignment in relation to the dish itself. I have also received a Stab HH90 motor and an Invacom QPH-031 LNB. I'm waiting to order a Genpix SkyWalker-1 USB box if it ever comes back in stock!

I'm at about 48 degrees latitude and -122 degrees longitude and for my setup I got data from DishPointer.com - Satellite Dish Pointer / Alignment Calculator with Google Maps of: Motor Latitude Angle matching my actual latitude; True Azimuth of 180 degrees; Magnetic Azimuth of 162.1 degrees; Dish Elevation of 38 degrees and the one that is bugging me, Declination Angle of 7.1 degrees. Stab's installation instructions make no mention of this angle and I can't seem to relate it plus or minus to any of the other numbers I have. I did some Googling but haven't found a satisfying answer. I am also thinking that this number is extraneous for me and already figured in to the motor and dish angles taken together. Even if I don't need to include it in my calculations, I am the sort that has a hard time accepting things without an understanding of the underlying facts or reasons. Anyone care to tackle an explanation?

I see there are degrees marked on the clamp for the neck of the LNB for adjusting LNB skew. Am I correct that with a motorized dish at the midpoint of motor travel that will be set up pointing true South that the LNB should be skewed at zero and after that the skewing is automatically correct as the dish tilts and rotates?

Rob
4 Replies · 2581 views
M
if you set up the motorized correctly you should not have to mess with skew since it'll do it for you... You may however have to tweak a little bit if you're just barely off of true south, have a pole that isn't 100% plumb, or somehow managed to be a tad off center on your true south. Typically though, once you get true south in, and find you can get good quality on both sides of the arc you are good to go. Just make sure that your quality is as good as you can get it elevation wise... which may require adjusting by hand without even touching a bolt. a fraction of an inch can make or break you, especially on very low signal feeds and things.
concord
You use the "Declination Angle" by subtracting/adding it to the dish elevation angle, for the HH90, check out:

How to install an HH-Mount Motor? Applies to DG240-SM3D22-STABHH100-HH120-Motech-SG2100
R
Thanks for the replies. The Sadoun help page in the link provided is powered by the same dishpointer site that I already used. I have done some more reading online and have found the answer I was seeking: the declination angle is subtracted from a fixed number (the bend angle of the dish mount arm coming off of your motor) to arrive at the dish elevation number. In the case of the Stab HH90, this is 45 degrees (and is different for different motors). This is why I couldn't correspond the declination angle to any of the numbers I already had in front of me. The dish elevation angle given on the website already takes it into account so I think it is actually confusing rather than helpful since no explanation of its significance is provided there.

Rob
concord
Glad you were able to figure it out....when I set mine up, I think he had a different page than the current one...
osu1991
Pub Member / Supporter
Last reply · posted in The Chit Chat Club
:mad::mad::mad::mad:

Pissed off at the crappy healthcare costs

My health Insurance renewal for 2027 just came in. Going from $827 a month to $1,187 a month. Deductible going up a $1k to $9,350. Max out of pocket also going up $1k to $11,000. Doctor co-pay of $40. Urgent Care co-pay $50. ER 50% coinsurance after deductible. That's all in network. Out of network is double, should it be needed.

Have to think about this. I'm really tempted to just go without now. I only go to the doctor once or twice a year. I pay out of pocket for Tirzepitide and can do without the Rosuvastatin (crestor) now. Really tired of spending over $10k a year and getting nothing out of it.

After years with Blue Cross I switched last year to Ambetter as my Blue Cross premium was going from $1200 to $1800 for a Silver plan and the Bronze plan was still going to be $1300 at BCBS. Ambetter was $827 for the same coverage with a Bronze plan. Didn't think it would jump this much so soon.

I'm guessing a Silver plan is probably over $2,000 a month for 2027.
10 Replies · 92 views
  • Sad
Reactions: AZ.
b4pjoe
Pissed off at the crappy healthcare costs
Are you employed with no work insurance or that is what you are paying for your workplace insurance? Or is that through Healthcare.gov? Retired? Eligible for medicare?
vazhog
that cut is only for illegals to get off the rolls and I was being sarcastic before -
T
The 2030s will likely bring renewed health reform
osu1991
Are you employed with no work insurance or that is what you are paying for your workplace insurance? Or is that through Healthcare.gov? Retired? Eligible for medicare?
Started my own business in 2006, been self employed for 20 years this year.
meStevo
that cut is only for illegals to get off the rolls and I was being sarcastic before -

Even sarcastically it's wrong. Undocumented immigrants already weren't eligible for federal Medicaid, so there's no one to "get off the rolls." The immigrant-related pieces are a small part of the ~$1 trillion. They cut the federal match for emergency care from 90% to the state's regular rate and end eligibility for some lawful immigrants like refugees. Most of the "savings" come from work requirements, more frequent eligibility checks, and provider tax limits, which hit citizens.

Either way, the cost doesn't disappear. It shifts to states, hospitals, and everyone else's premiums and will only serve to make issues like those raised in this thread worse.
  • Like
Reactions: osu1991
dishstaller
Undocumented immigrants already weren't eligible for federal Medicaid, so there's no one to "get off the rolls."
That's only part correct. Actually I had to look it up to make sure. There is NO Federal money going to Medicaid for illegals but there ARE some states that use State money to pay for Medicaid for illegals. Here's the list

    • California: Covers all income-eligible undocumented adults. [1, 2]
    • Colorado: Covers specific adult demographics (with upcoming budget caps in 2027). [1]
    • Illinois: Covers specific adult age brackets. [1]
    • New York: Covers specific adult demographics. [1]
    • Oregon: Covers all income-eligible undocumented adults. [1, 2]
    • Washington: Covers specific adult demographics. [1, 2]
    • Washington, D.C.: Provides adult coverage through the D.C. Health Care Alliance. [1, 2]
meStevo
That's only part correct. Actually I had to look it up to make sure. There is NO Federal money going to Medicaid for illegals but there ARE some states that use State money to pay for Medicaid for illegals. Here's the list

    • California: Covers all income-eligible undocumented adults. [1, 2]
    • Colorado: Covers specific adult demographics (with upcoming budget caps in 2027). [1]
    • Illinois: Covers specific adult age brackets. [1]
    • New York: Covers specific adult demographics. [1]
    • Oregon: Covers all income-eligible undocumented adults. [1, 2]
    • Washington: Covers specific adult demographics. [1, 2]
    • Washington, D.C.: Provides adult coverage through the D.C. Health Care Alliance. [1, 2]

Fair point, but it's consistent with what I said: no federal Medicaid money goes to undocumented immigrants. Those programs are state-funded, so the federal ~$1T cut can't touch them. Whatever states decide to do with their own programs is a separate budget decision.
  • Like
Reactions: osu1991 and Bobby
Scott Greczkowski
Staff member HERE TO HELP YOU! Cutting Edge
Last reply · posted in The Chit Chat Club
Sometimes a thread gets so many posts in it that is can cause issues for the server so that why today we introduce The Song Name Game Part 3!

So let the game continue!

The last song was added by Bobby who posted...

One Meat Ball - Andrews Sisters

CONTINUE ON AND HAVE FUN! WELCOME HOME TO SATELLITEGUYS.US!

Here are the original rules for the game as posted by WebbyDude back in 2006. http://www.satelliteguys.us/threads/68645-Song-Name-Game

Just name a song title and the band who performed it. The next person does the same thing, but needs to list a song title or band name which includes a word from the previous entry. Pick songs from any genre.

Example:

Long Live Rock and Roll -- Rainbow

Rainbow in the Dark -- Dio

Another example:

Ride the Lightning -- Metallica

Lightning Strikes -- Ozzy Osbourne


Get it?


An additional note: we all know that song titles, sometimes, use profane words. Because this is a family friendly website it is advised that you clean up that title up a bit. This is accomplished by using something like sh!t instead of the real word. Thanks....
68674 Replies · 2680943 views
  • Like
Reactions: c-spand
gms49ers
Can't You Hear Me Knocking - The Rolling Stones
long_time_Dish
I Can Hear Music - The Beach Boys
dishstaller
Boom Boom ( Out Go The Lights ) - Pat Travers
sdfntx
Palisades Park - Freddy "Boom Boom" Cannon
RaiderPower
Cherry Hill Park - Billy Joe Royal
dishstaller
Pub Member / Supporter Lifetime Supporter
Last reply · posted in DISH Network Support Forum
I figured some of the guys would be looking here for an answer. You'll need to use this link

I'll mention what happened over there. I don't want to cause Scott any issues or put him in a bad spot.
1 Replies · 31 views
dishstaller
If any of you know some of the guys from the board and you have their contact info, please reach out to them....many failed to update their contact info and some even had starband email addresses.
  • Like
Reactions: charlesrshell
dfergie
Staff member HERE TO HELP YOU!
Last reply · posted in What's Cooking?
We have a Breakfast and Dinner thread so... :)
Continuing from the Breakfast thread, found Cornbread mix so ...
Yellow Cornbread Mix
2 Hatch Green Chiles -diced
1 Egg
2/3 cup of milk
add to greased pan
Bake for 400f 20-25 minutes(From instructions)
now to put together and try... this to go with pinto beans...
5450 Replies · 336193 views
dfergie
Chili dog bowl, water… (homemade chili)
TRG
TRG
Leftover wanton soup and pork fried rice. Water.
dfergie
IMG_5955.webp

Sweet tea…
  • Like
Reactions: Bobby and TRG
TRG
TRG
Tuna salad sandwich on toasted honey whole wheat bread with a handful of kettle chips. Water.
  • Like
Reactions: Bobby
TRG
TRG
Breakfast for lunch. Crispy corned beef hash, home fries, two over easy eggs and sourdough toast.

1653.webp
  • Like
Reactions: osu1991 and Bobby
dfergie
Staff member HERE TO HELP YOU!
Last reply · posted in The Sports Section
160 Replies · 3642 views
  • Like
Reactions: Foxbat and meStevo
Foxbat
Weird F1 weekend is already over with a Saturday race.
dfergie
Tried to watch the truck race but the stage c**p is why I don't watch NASCAR anymore…
  • Like
Reactions: Yespage
Y
Today is the anniversary of Dan Wheldon's passing at Las Vegas in a dreadful crash that luckily didn't take more drivers' lives. I vaguely remember the crash, but I more strongly remember Paul Tracy trying to keep it together as he left the Medical Center knowing that Dan most likely wasn't going to.

The safety in these vehicles is beyond incomprehensible, especially relative to what it was 60 years ago, when dying wasn't unexpected. But it is still very dangerous. I always scoff at the prayer invocations, but never scoff at the risks these drivers take and the emergency workers out there who might need to pull short of a miracle to save a driver's life.
Tried to watch the truck race but the stage c**p is why I don't watch NASCAR anymore…
HBO Max has the live in car streaming without commercials, which provides an interesting take, but you are driving blind, knowing only what the team is telling the driver about what is happening on the track. The stages definitely ruin the NASCAR set up.
  • Like
Reactions: dfergie
Y
NASCAR is an abject mess, but at least it has Kyle Larson. Guy had the lead on the green/white checker, fell back to 12th or the like, kept his cool, and charged back to win with room to spare at the line. And win very cleanly!

NASCAR needs to stop racing at Talladega. Especially if they are going for elderly Sunday drives at the track! Stage racing is real stupid, but NASCAR should consider one half point a second per group gap as a bonus.
Tom Speer
Staff member Pub Member / Supporter Cutting Edge
· posted in DIRECTV General Forum
If you are a former Cuttinge Edge member who has converted to Stream, please contact me.
0 Replies · 25 views
M
Last reply · posted in DISH Network Support Forum
Over the past few weeks, I have had problems connecting to streaming services (Netflix, HBO et al). When I go to the TV's native Channels, I have no problem. The Dish internet troubleshooter shows I have a good internet connection. I'm wondering whether it's an issue with my internet provider or a problem with the Dish software on the Hopper Plus. Anyone else seeing this?
7 Replies · 298 views
Almighty1
Over the past few weeks, I have had problems connecting to streaming services (Netflix, HBO et al). When I go to the TV's native Channels, I have no problem. The Dish internet troubleshooter shows I have a good internet connection. I'm wondering whether it's an issue with my internet provider or a problem with the Dish software on the Hopper Plus. Anyone else seeing this?
I have a DISH Hopper 3 (Software H713) with Hopper Plus (Software P15403). I have not tried streaming services but I primarily watch TVB Jadeworld international package which is only available by streaming and when I have an issue, I usually have to go to a non-streaming satellite channel first before the streaming channels will work again. What software versions do you have and what is the error message if any are showing on your screen? or is that Dish downloading logo just stuck and never finishes?
  • Like
Reactions: charlesrshell
M
I have a DISH Hopper 3 (Software H713) with Hopper Plus (Software P15403). I have not tried streaming services but I primarily watch TVB Jadeworld international package which is only available by streaming and when I have an issue, I usually have to go to a non-streaming satellite channel first before the streaming channels will work again. What software versions do you have and what is the error message if any are showing on your screen? or is that Dish downloading logo just stuck and never finishes?
I'm on H713 on the Hopper and P15403 on the Hopper Plus. It shows internet connection issues and doesn't finish loading the various services. I see the "loading circle going around. Sometimes I get a message saying that the service is having trouble loading my content and to check the internet connection.
  • Like
Reactions: charlesrshell
Almighty1
I'm on H713 on the Hopper and P15403 on the Hopper Plus. It shows internet connection issues and doesn't finish loading the various services. I see the "loading circle going around. Sometimes I get a message saying that the service is having trouble loading my content and to check the internet connection.
Did it ever work correctly before? Hard to say what the problem is. Usually for streaming, it will show the Dish logo with lines sweeping down to show downloading, never seen the circle issue. Did you try a manual reboot, red button reset, power cord unplug/replug to see if it makes a difference.
  • Like
Reactions: charlesrshell
S
Did it ever work correctly before? Hard to say what the problem is. Usually for streaming, it will show the Dish logo with lines sweeping down to show downloading, never seen the circle issue. Did you try a manual reboot, red button reset, power cord unplug/replug to see if it makes a difference.
Might be worth just to ditch the hopper plus. No issues here on h713
  • Like
Reactions: charlesrshell
S
Over the past few weeks, I have had problems connecting to streaming services (Netflix, HBO et al). When I go to the TV's native Channels, I have no problem. The Dish internet troubleshooter shows I have a good internet connection. I'm wondering whether it's an issue with my internet provider or a problem with the Dish software on the Hopper Plus. Anyone else seeing this?
Buy a roku and dump the hopper plus you'll be better off. If you have a smart tv you don't need either one. No hopper plus here and no issues!!!
Almighty1
Might be worth just to ditch the hopper plus. No issues here on h713
I have a Hopper Plus and no issues either. charlesrshell has both a Hopper 3 with Hopper Plus and one without, he doesn't have the same issue. Before blaming it on the Hopper Plus, he should see if the problem still exists without the Hopper Plus connected as it could be the Internet connection itself or some setting in the router itself. There is someone in another thread who has EHD issues on the Hopper 3 only setup but does not have the EHD issues on the Hopper 3 with Hopper Plus and he has already tried swapping the EHD and it did not make a difference so like the saying, YMMV.
  • Like
Reactions: charlesrshell
Almighty1
Buy a roku and dump the hopper plus you'll be better off. If you have a smart tv you don't need either one. No hopper plus here and no issues!!!
The Roku costs $$$, Hopper Plus is free. That may not be the only costs as it depends if the TV in question still has available HDMI ports and if not, it will require a HDMI switch and HDMI cable which adds more to the cost.

I have a LG 3D OLED Smart TV and I still need either of them because it does not have Android TV built in. Add a Hopper Plus and see if you actually have issues or not as until you actually tried it, it means nothing.
  • Like
Reactions: charlesrshell