Social Feed

N6BY
Lifetime Supporter
Last reply · posted in DISH Network Support Forum
I have a Vip 722 with L618 software in single mode.

I watch Fox Business HD a lot. I'm seeing frequent video jitters, and its especially noticeable in the scrolling text. Its goes smoothly for a bit, then it pauses briefly and skips. Its doing this at a frequency which varies from several times per second to once or twice a minute. Sometimes its un-watchable.

I called Tech Support about this last week and they had me check the System Info and press the 'Details' button. I read them the numbers after Value 0 through Value 9, which somehow indicate the health of the hard drive. They said my numbers indicated a bad hard drive and sent me a new receiver.

So I installed the replacement receiver last night and unfortunately I'm seeing the same problem -- and its worse than my original receiver. Plus it cost me $16.18 in shipping and tax for the replacement.

Is this a known software problem? is anyone else having this problem or know of a solution?
16 Replies · 3924 views
K
I haven't had any problems since Monday evening, but after reading everyone's posts I checked my VIP 722 temps and found 138 high, 114 low and 129 average. Hard to figure out why they are so high. The house temp is set at 78 and rarely exceeds that. The DVR is in a home made cabinet that is open on two sides - front and left side - and has about 8 inches clearance above it, so I am not sure what can be done to cool it down.

Question - does the temp counters ever reset or do they carry the highest and lowest for the life of the receiver? Is there a way they can be reset?
K
I've had what I think is the same issue for about 2 weeks. Sometimes when I fast forward or skip ahead, picture will be very jumpy or freeze for 10-15 seconds. It locks up like an overloaded computer would with a fragmented hard drive. I did not notice anything like this prior to 2 weeks ago and now it's consistent. Box is not housed and is in the open. Don't think overheating has anything to do with this. Was there a software update recently? I'm suspecting something more along those lines. Anyone else seeing this issue????
Ganthet
I just started having the same issue tonight - but only on the HD channels. A soft reboot fixed the problem - for now. I'm using component so I know it's not an HDMI issue

I also checked the same channel on my 211 and it was working fine.

I do have the new L622 software. I'm praying this is not a bug.
N6BY
Its not the HDMI cable

Earlier in this thread someone suggested the possibility of correcting this problem with a better HDMI cable.

After switching HDMI cables and noticing no change in the frequency of video jitters, I decided to try the following test to help isolate the problem:

I had my 722 simultaneously connected to 2 TVs, one through the HDMI output and one through the S-Video output.

Both TVs showed the same jitter at the exact same times. I tested this with channels that have scrolling banners. So I have ruled out the cable and the TV as possible causes.

This problem could be heat related, but I think its more likely to be a software issue. I have noticed that unplugging the 722 for about 30 seconds and then plugging it back in makes the problem go away for a while. This resets the software and clears all the buffers.

But using an external fan aimed at the air intake does not seem to affect it. The jitters still occur but the 722 feels much cooler to the touch, so I know the fan is dramatically lowering the temperature.
N6BY
Problem solved!

I know that this is an old thread, but I want to post the solution to this problem to help anyone else experiencing this issue.

I did a 'System Info' (menu, 6,1,3) and it reported 'LNB Drift Detected on 129' of -6 to -8. (I have a DPP Twin for 110/119 and a wing dish for 129).

So last week I got a new LNB for the 129 wing dish and it completely solved the problem!

No more video jitters or dropped frames!

For a long time I had assumed that this was a software problem. But that didn't make sense because if it was software and everyone had the same problem, then there would have been many complaints. Also the jittering video only happened on channels from the 129 satellite, like Fox Business HD which I watch a lot.

Anyway, I hope this info helps others who have video stutter due to a bad LNB.
dishstaller
Pub Member / Supporter Lifetime Supporter
Last reply · posted in The Chit Chat Club
5 Replies · 66 views
  • Like
Reactions: dfergie
dishstaller
Sorry for posting the wrong link. Just corrected it.
  • Like
Reactions: Foxbat
dfergie
I loved it when Rodney was on the Tonight Show...
Foxbat
Sorry for posting the wrong link. Just corrected it.
Thanks, I wasn't sure if you had the wrong Subject or the wrong YouTube link.
osu1991
Was a Don Rickles fan. I've dvr'd most of his appearances on Carson from the antenna tv replays.

Neutron
Supporting Founder
Last reply · posted in The Chit Chat Club
Patrick Stewart died yesterday, October 28th at the age of 86. We lost yet another great actor. :(

2 Replies · 12 views
  • Sad
Reactions: osu1991
T
1793305116126.webp
  • Like
Reactions: sdfntx
dfergie
This hits hard, R.I.P. ...
"MysteryMan"
Pub Member / Supporter Cutting Edge
Last reply · posted in Computers and Gadgets
I created this thread on the original Edgecutter Cutting Edge Forums site. It's simply a place for those to review the latest software available for those using Windows 10 and Windows 11. To date it has received 112,559 views. I have been asked by staff to continue this thread here.
524 Replies · 48054 views
EarDemon
If it wasn't for what I want, I wouldn't need any of this.

Do I need a collection of handheld radios, scanners and speed enforcement countermeasures? Nope, but I want them. Very little, if any of the software used to interface with these devices is available on Linux.
WhiteBeard
If it wasn't for what I want, I wouldn't need any of this.

Do I need a collection of handheld radios, scanners and speed enforcement countermeasures? Nope, but I want them. Very little, if any of the software used to interface with these devices is available on Linux.
To each there own but I've found that Windows can't do much more than Linux can. Can't have everything. ☹️
  • Haha
Reactions: meStevo
EarDemon
To each there own but I've found that Windows can't do much more than Linux can. Can't have everything. ☹️
For niche use cases, yes I agree. Kali for ethical hacking and security testing, and running a Cacti server for network monitoring are the two things I have experience in. Plus thousands and thousands of other things, but for every day use I just can't see it. The owner of the GMRS repeater that I pay to access is changing the Tx DPL tones tomorrow, while Chirp is available on Linux, the software to program my MXT500 is not.

I run Fedora and Ubuntu in VMWare, honestly I don't care much for the UI of either of them and I don't feel like spending days/weeks to customize the UI to make it look Windows-like when I could just use Windows. The cartoonish dock at the bottom of the screen reminds me of Apple products.
harshness
I don't care much for the UI of either of them and I don't feel like spending days/weeks to customize the UI to make it look Windows-like when I could just use Windows.
What is so fantabulous about the Windows UI? By many accounts, it has been going downhill since Windows 7.

There are Linux desktops that offer Windows or Mac UIs, yet you don't hear much chatter about them outside of questions about when the creators might get sued.
  • Like
Reactions: HipKat
EarDemon
What is so fantabulous about the Windows UI?
Because it's what I prefer. I know I've said this a few times, I use Open Shell to give me the cascading start menu a la WIN 95 and NT4.0. The only reason I went from Windows Vista to 7 back in the day was because of Classic Shell. I cannot stand anything other than the OG start menu from 30+ years ago. I'm using ExplorerPatcher to give me Windows 10 UI elements of the taskbar and right click context menus.

If you could take a look at how I set up Windows 95, you'd find many similarities to how I use 11.
  • Like
Reactions: cp2k
EarDemon
I could probably use that as a starting point, but I don't like the full size icons. If you have to click on each folder that's also a no-go for me, it has to be cascading.

I used to have Peppermint Linux in a VM, that was about as close as I could get to recreating a Windows NT4.0 style of menu structure, but I could never get it to scale properly in VMWare on a 4K display and eventually gave up.

Whatever the boot up time it's fine with me. The longest part of my bootup is the HP SureStart BIOS integrity check. Once that is done, it's only a few more seconds. I haven't done this reg tweak yet since the reformat, but I switched the bootup animation to the Windows 10 style spinning circle of dots, and it's two and a half rotations. I can live with that.
harshness
Because it's what I prefer.
I hope you don't believe that makes it wonderful (especially when you're using workarounds for Microsoft's malfeasance).

I use LibreOffice as opposed to Microsoft office (even in Windows) because it's UI is like the Office of old, so I'm putting my money where my mouth is (in a manner of speaking). The ribbon was one of the worst ideas to come out Redmond.
HipKat
I could probably use that as a starting point, but I don't like the full size icons. If you have to click on each folder that's also a no-go for me, it has to be cascading.

I used to have Peppermint Linux in a VM, that was about as close as I could get to recreating a Windows NT4.0 style of menu structure, but I could never get it to scale properly in VMWare on a 4K display and eventually gave up.

Whatever the boot up time it's fine with me. The longest part of my bootup is the HP SureStart BIOS integrity check. Once that is done, it's only a few more seconds. I haven't done this reg tweak yet since the reformat, but I switched the bootup animation to the Windows 10 style spinning circle of dots, and it's two and a half rotations. I can live with that.
I used to pin the C: drive to the Win Taskbar and it would open in cascading style
"MysteryMan"
2026-10 Preview Update Builds: 26300.9818 and 26200.9818 (KB5127936) has been released. Moderate time needed for those choosing to perform a manual download/install/restart. Quality improvements only. No new operating system features.
  • Like
Reactions: Tweek
JSheridan
Actually it looks like there are a lot of features new or updated, although most are on a gradual rollout schedule.

M
Last reply · posted in Over the Air Television By RabbitEars.Info
Interesting article about the work being done to develope an ATSC 3 converter box. Yes it does mention affordable.
13 Replies · 747 views
primestar31
DEATH TO NEXGEN!
star trek GIF


It's dead, they just don't know it yet. They killed it by forcing DRM on it, and that TOTALLY botched implementing it.

There is absolutely NO compelling reason for anybody to switch to ATSC3.0. They only want it as a total and complete money grab.
Mister B
What bothers me is the total waste of broadcasting spectrum in this very crowded market. It has been almost three years now since KFOX converted their broadcast tower to ATSC 3.0 and moved all of their channels to other towers causing noticeable degradation of the picture quality.
I have a Sony TV with 3.0 capabilities but still use the 1.0 version of locals due to the fact that one or all of the 3.0 channels are often missing or unwatchable. In this city of 800K I doubt that more than a few hundred even know about ATSC 3.0.
The only thing that could motivate me to be interested in 3.0 would be if all of the minor networks (diginets) could be in at least 720P rather than blurry ultra-compressed 480i.
Three years is long enough to waste one of the few available RF frequencies in the area for this trial.
It is time to either move on with this experiment or call it quits.
navychop
It is time to either move on with this experiment or call it quits.

QFT. Of course, my preference involves a curb and some kicking.
  • Like
Reactions: FTA4PA
S
star trek GIF


It's dead, they just don't know it yet. They killed it by forcing DRM on it, and that TOTALLY botched implementing it.

There is absolutely NO compelling reason for anybody to switch to ATSC3.0. They only want it as a total and complete money grab.
WHAT ABOUT THE INTERNET PART OF IT. NO ONE WANTS A BOX CONNECTED TO THE INTERNET EITHER.
navychop
Cough, cough. COVID vaccine implants.

:oldlaugh
  • Haha
Reactions: HIFI
Foxbat
Cough, cough. COVID vaccine implants.

:oldlaugh
That would be handy. Download the latest RNA snippets that can be updated over 5G and no more shots! You're a Genius!
  • Haha
Reactions: navychop
R
I want it and I have to have it.

I can neuter the phoning home with adguard home so it won't be doing that in my castle but I prefer without Internet so that my TVs in the house don't turn into e-waste
M
Last reply · posted in DISH Network Support Forum
Over the past few weeks, I have had problems connecting to streaming services (Netflix, HBO et al). When I go to the TV's native Channels, I have no problem. The Dish internet troubleshooter shows I have a good internet connection. I'm wondering whether it's an issue with my internet provider or a problem with the Dish software on the Hopper Plus. Anyone else seeing this?
1 Replies · 96 views
Almighty1
Over the past few weeks, I have had problems connecting to streaming services (Netflix, HBO et al). When I go to the TV's native Channels, I have no problem. The Dish internet troubleshooter shows I have a good internet connection. I'm wondering whether it's an issue with my internet provider or a problem with the Dish software on the Hopper Plus. Anyone else seeing this?
I have a DISH Hopper 3 (Software H713) with Hopper Plus (Software P15403). I have not tried streaming services but I primarily watch TVB Jadeworld international package which is only available by streaming and when I have an issue, I usually have to go to a non-streaming satellite channel first before the streaming channels will work again. What software versions do you have and what is the error message if any are showing on your screen? or is that Dish downloading logo just stuck and never finishes?
  • Like
Reactions: charlesrshell
dishstaller
Pub Member / Supporter Lifetime Supporter
· posted in The Chit Chat Club
It states the average amount they are under water is OVER $7,000. :eek

Personally, I tend to be the type that drives a vehicle for a lot of years....do my own oil changes and other fluid changes. Just replaced the spark plugs and a couple coils. Youtube is great for things like this.

0 Replies · 12 views
  • Like
Reactions: navychop
Scott Greczkowski
Staff member HERE TO HELP YOU! Cutting Edge
Last reply · posted in The Chit Chat Club
Sometimes a thread gets so many posts in it that is can cause issues for the server so that why today we introduce The Song Name Game Part 3!

So let the game continue!

The last song was added by Bobby who posted...

One Meat Ball - Andrews Sisters

CONTINUE ON AND HAVE FUN! WELCOME HOME TO SATELLITEGUYS.US!

Here are the original rules for the game as posted by WebbyDude back in 2006. http://www.satelliteguys.us/threads/68645-Song-Name-Game

Just name a song title and the band who performed it. The next person does the same thing, but needs to list a song title or band name which includes a word from the previous entry. Pick songs from any genre.

Example:

Long Live Rock and Roll -- Rainbow

Rainbow in the Dark -- Dio

Another example:

Ride the Lightning -- Metallica

Lightning Strikes -- Ozzy Osbourne


Get it?


An additional note: we all know that song titles, sometimes, use profane words. Because this is a family friendly website it is advised that you clean up that title up a bit. This is accomplished by using something like sh!t instead of the real word. Thanks....
68659 Replies · 2680307 views
  • Like
Reactions: c-spand
Bobby
98.6 - Keith
harshness
I'm Easy - Keith Carridine
gms49ers
It's Easy - Boston
  • Like
Reactions: long_time_Dish
RaiderPower
Take It Easy On Me - Little River Band
long_time_Dish
Take It Easy - The Eagles
  • Like
Reactions: gms49ers
jamieh1
Last reply · posted in DIRECTV Programming Forum
DIRECTV Stream/Internet added Ch 4105 SportsGrid
268 Replies · 38730 views
  • Like
Reactions: c-spand and KyL416
K
Now live:
4101 Yahoo! Sports Network
4121 DP World Tour
4195 F1 Channel
4196 MotoGP Channel
K
Now live:
4275 Law & Crime
4364 Military Makeover Channel
K
Game Show Central is now live on channel 4342
K
Now live:
4101 Yahoo! Sports Network
4121 DP World Tour
4195 F1 Channel
4196 MotoGP Channel
It only took them 41 days to announce it
  • Like
Reactions: Mr Tony
K
TWiT Tech Podcast Network
· posted in TWiT Tech Podcast Network
0 Replies · 7 views
dfergie
Staff member HERE TO HELP YOU!
Last reply · posted in What's Cooking?
We have a Breakfast and Dinner thread so... :)
Continuing from the Breakfast thread, found Cornbread mix so ...
Yellow Cornbread Mix
2 Hatch Green Chiles -diced
1 Egg
2/3 cup of milk
add to greased pan
Bake for 400f 20-25 minutes(From instructions)
now to put together and try... this to go with pinto beans...
5449 Replies · 336102 views
TRG
TRG
Club sandwich and corn chowder. Iced tea.
dfergie
Chili dog bowl, water… (homemade chili)
TRG
TRG
Leftover wanton soup and pork fried rice. Water.
dfergie
IMG_5955.webp

Sweet tea…
  • Like
Reactions: Bobby and TRG
TRG
TRG
Tuna salad sandwich on toasted honey whole wheat bread with a handful of kettle chips. Water.
  • Like
Reactions: Bobby