Social Feed

B.J.
Last reply · posted in Free To Air (FTA) Discussion
I'm just curious whether anyone has run into any of their FTA receivers that would tune below 950 MHz IF freq, which would be less than 11700 on a standard LNBF or above 4200 on C band, OR below 12200 on a circular DBS lnbf?

I'm aware that our LNBs and LNBFs give signal above and below their published range, and it's pretty well know that you can tune above 1450 IF, such as to tune the 12224 Nimiq signals using a linear LNBF on G17.

However, it's always been my assumption that there weren't any STBs, or drivers for computer card receivers that would tune below the 950 MHz bottom of the IF band. I think my receivers give an error if I try, although I really haven't tried it on all of them. But it's been a bit frustrating to see that Anik F3 sat sitting there at 118, and not being able to tune it with a circular LNBF because it would be below 950, and not being able to get good reception using a linear LNBF because it's circular.

Well, today, I accidently tried tuning one of the F3 transponders with the Genpix, using the QPH-031. It WORKED. It worked well actually. I was actually able to tune down at least to 12002 L 20000 , and might have been able to go further except I suspect that the signals I tried lower than that, but that's where I stopped getting locks.

I was real surprised at this, because that means that the Genpix is tuning down to 750 MHz, which is a pretty wide frequency range without going through some changes in IF freqs or something.

But then, I tried tuning those freqs with my old Twinhan, and it "seemed" to be locking transponders too, so I decided that I must be remembering wrong that I had tried this before and failed. But then a couple hours later, I remembered that TSREADER with the Twinhan has this habit of if you've tuned out of range, it will just give you a lock on what you last tuned in succesfully, so I tried it again, this time looking at the channel lineup, and found that the Twinhan was NOT actually going below 12200, but was locking on a transponder above 12200.

But the Genpix actually IS locking on signals up to 200 MHz below the 950 lower end of the IF band. Of course, there wasn't anything to view down there, but I found it interesting that it would do that.

I'll have to check to see if there are any linear sats, like over the atlantic, that have signals down below 11700, that I can try with the Genpix.

Anyway, I'm just curious whether any other receivers do this, and/or is it just the Genpix that is capable of sub band tuning?
4 Replies · 1377 views
P
Many PC-based tuners can be run lower (and higher), but it depends on the driver. Linux is normally the most direct path to make such tricks work.
zamar23
I assume that all FTA receivers that are known to be popular with so called "pirates", are capable of tuning Anik F3 whole emitting freqs range. There seems to be plenty of circular LNBFs on the market with 10750 LO that help make it happen. :) But I'm not sure if any clear programs are still left on that sat, or were available before.
updatelee
be aware that sometimes the receiver is locking signals below 950 but they are actually *images* of higher signals, I noticed my dreambox was locking many signals far below 950, then I noticed these same freq higher up lol. I will defn try my genpix though, would be interesting to see.
B.J.
be aware that sometimes the receiver is locking signals below 950 but they are actually *images* of higher signals, I noticed my dreambox was locking many signals far below 950, then I noticed these same freq higher up lol. I will defn try my genpix though, would be interesting to see.

I'm familiar with images from scanners, but I didn't think the LO freqs in sat receivers made this likely. As I mentioned above, I have seen transponders appear to LOCK below the 950 IF, when they were actually locked on a higher freq, but that was mainly with my Twinhan, since it has a habit of just locking on the last transponder with parameters within it's acceptable limits, when you try entering something out of range.

But that's not what I'm seeing with the Genpix. I verified that it was indeed seeing the lower band by pulling up the NIT on the transponder, which shows what channel numbers should be on each transponder on ALL DN sats, and the channel numbers matched what I was seeing on the transponder.
Bruce
Supporting Founder Lifetime Supporter
Last reply · posted in Internet Television (IPTV) Discussion Forum
I was reading this article


That said this-
Last summer, for the first time, streaming services like Netflix and Amazon Prime claimed the largest share of the television viewing audience, surpassing both cable and broadcast TV. Streaming captured 34.8 percent of July viewers, according to Nielsen data, compared to 34.4 percent for cable and 21.6 percent for broadcast.

And then, sometime in the second half of 2022, cord-cutters became the majority. The share of cable and satellite television subscribers dipped to 48 percent, according to a report from Samba TV, a television technology company.


Now I do not consider those with YTTV and the likes, Cord Cutters, but they still do not have Traditional Cable/Satellite delivered Live TV, so I decided to do the math.

There are, now, 129 Million Households in the United States.

In 2015, there were 100 Million Cable/Sat Subscribers , no streaming Live TV Service.

Today, there are 66 Million Live TV subscribers, including Cable, Satellite and Streaming.

Roughly, Streaming Live TV has 14 Million subs including all of them.

So that means, Cable/Satellite now has, roughly, 51 Million Households

So in just 8 years, lost 49% of their subscribers and by the end of this year, expected sub count to be, roughly, 45 million households.

That means a total loss of 55% since 2015 at the end of 2023.

But out of 129 Million households, 45 million will mean only 35% will get Cable/Satellite Delivered Live TV by the end of 2023.

Imagine what 2024 will be like.
876 Replies · 71316 views
  • Wow
Reactions: MikeD-C05
Bruce
Some interesting information was in this article-


This first-

The total pay-TV sector (traditional service providers and virtual MVPDs) shed 885,000 subscribers in Q2 2026

So with the loss of 2.03 Million in the first quarter, already at 2.915 Million gone this year, two quarters left to report.

#2-

The segment ended Q2 with 61.51 million subs comprising 27.5 million cable video subs, 21.42 million vMVPD customers, 9.56 million satellite TV customers, and 3.01 million telco TV subs.

There are approximately 133.97 million households in the United States, according to recent YCharts US Households Data from mid-2026.

That means more than 72 Million households do not have a paid live TV service, about 54% of the total.

What is worse, 7 years ago, paid live TV had over 80% of the population subscribing ( about 100 Million), almost all were Cable/Satellite customers.

Today, only about 37 Million subscribe to Cable/Satellite, less than 28% of our population.

#3-

At one time, Satellite TV (Dish and DirecTV), had about 34 Million subscribers added together, now, 9.56 Million.

That is over a 70% loss for those who subscribe to Satellite TV.

For Cable TV, not as bad, since they have broadband to help against the losses ( bundles), but as more options appear ( 5G, fiber, starlink, etc), I expect a big increase in those leaving cable.

Also expect YTTV to really start gaining even more subscribers, for those who still wish to have a live TV service, based on price point and it is a really great service.
Bruce
Looks like Optimum Communications ( formerly CableVision) is collapsing, due to it's high debt, lenders/creditors are taking over-

Bruce
Sony is discontinuing it's last 4K disc player, Panasonic has been rumored to be doing the same, the end of physical media is unfortunately, about to happen.

  • Sad
Reactions: navychop
navychop
Got a Sony 700 at WM dot commie.

I think.

Ordered, anyway. Amazon let me go thru entire process but then said no inventory.

Hopefully,, WM will come thru.
dishstaller
Sony is discontinuing it's last 4K disc player, Panasonic has been rumored to be doing the same, the end of physical media is unfortunately, about to happen.
Hate to hear that. If you don't physically have something in your hand, you don't really own it.
TWiT Tech Podcast Network
· posted in TWiT Tech Podcast Network
0 Replies · 2 views
dishstaller
Pub Member / Supporter Lifetime Supporter
Last reply · posted in The Chit Chat Club
I'm surprised Walmart hasn't banned this guy from all of their stores. He has been on their CASE the past few months.


View: https://www.youtube.com/shorts/f3zr37ekgKM?feature=share
30 Replies · 300 views
  • Wow
Reactions: NYDutch
Juan
I'm surprised Walmart hasn't banned this guy from all of their stores. He has been on their CASE the past few months.


View: https://www.youtube.com/shorts/f3zr37ekgKM?feature=share

When walmart set a price...they weigh the container and the product...the product label only shows the weight of the product...I am sure if you brought your own plastic baggies to bring the product home you could get the cheaper price
dishstaller
When walmart set a price...they weigh the container and the product...
Then they are stupid. Everyone knows that the price per ounce should be the price per ounce of actual product.
  • Like
Reactions: Jimbo
Juan
Then they are stupid. Everyone knows that the price per ounce should be the price per ounce of actual product.
You are paying for the whole thing
T
You are paying for the whole thing
Well, the bag can't weigh that much, right? But by law food product packaging must display the actual net weight of the product, i.e., the contents of the container, so by any logic, if not law, a store's stated per-ounce cost should reflect that figure. But since there's not any law regulating shelf statements, a store can say whatever it wants without violating any rules. So I guess the answer is more consumer legislation. Or simply caveat emptor.
Juan
Well, the bag can't weigh that much, right? But by law food product packaging must display the actual net weight of the product, i.e., the contents of the container, so by any logic, if not law, a store's stated per-ounce cost should reflect that figure. But since there's not any law regulating shelf statements, a store can say whatever it wants without violating any rules. So I guess the answer is more consumer legislation. Or simply caveat emptor.
But a box can weigh more than an ounce..maybe 2...a can might weigh 5 ounces..a bag...not much
dishstaller
.a bag...not much
Well, according to the price per ounce on that first bag of coffee he mentions, that would mean the bag weighed over 6 ounces. That bag does NOT weigh 6 ounces. According to Google, an empty bag weighs half an ounce.
Juan
Well, according to the price per ounce on that first bag of coffee he mentions, that would mean the bag weighed over 6 ounces. That bag does NOT weigh 6 ounces. According to Google, an empty bag weighs half an ounce.
You need to weigh the actual bag...a deli bag weighs less than that but a thick coffee bag is gonna weigh around an ounce...an empty tin can has some weight
NYDutch
You need to weigh the actual bag...a deli bag weighs less than that but a thick coffee bag is gonna weigh around an ounce...an empty tin can has some weight
Products sold by the ounce, pound, etc, should always be priced for the product only. Only the shipping weight should include the packaging.
harshness
Products sold by the ounce, pound, etc, should always be priced for the product only.
Unless the specific product or its packaging is known at the time of weighing, estimating the tare weight for a PoS system is a tall order.

I'm pretty sure that produce bags can't get any thinner. ;)

You certainly don't want to put unbagged produce on a belt, scale, or in a clerk's hands (gloved or not).
Jimbo
Unless the specific product or its packaging is known at the time of weighing, estimating the tare weight for a PoS system is a tall order.

I'm pretty sure that produce bags can't get any thinner. ;)

You certainly don't want to put unbagged produce on a belt, scale, or in a clerk's hands (gloved or not).
I would think that all the packaging would already be accounted for ... they weigh the container, subtract that from the scale, then add the product , so its weighing the Product only
dishstaller
but a thick coffee bag is gonna weigh around an ounce...

Obviously you didn't read my post.....google says a coffee bag weighs half an ounce. But let's say you are correct and it DOES weigh a full ounce, that would still fall 5 ounces shy for Walmart's numbers to match.
You wouldn't happen to be kin to Bernie would you
Juan
Obviously you didn't read my post.....google says a coffee bag weighs half an ounce. But let's say you are correct and it DOES weigh a full ounce, that would still fall 5 ounces shy for Walmart's numbers to match.
You wouldn't happen to be kin to Bernie would you
None of it means a hill of coffee beans...the price is the price...its not going to get any lower...as long as you pay the price on the shelf at the register..there is no crime
dishstaller
None of it means a hill of coffee beans...the price is the price...its not going to get any lower...as long as you pay the price on the shelf at the register..there is no crime
I can't BELIEVE this is being such a difficult subject. The issue isn't the price....it's the advertised price per ounce. A lot of shoppers, myself included, use the price per ounce in determining which is the better value....with that number being inaccurate, it can trick someone into thinking that one product cost less per ounce than a competing product. Is this a crime?...above my pay grade. Is it dishonest? Yes.
  • Like
Reactions: Jimbo and AZ.
Juan
I can't BELIEVE this is being such a difficult subject. The issue isn't the price....it's the advertised price per ounce. A lot of shoppers, myself included, use the price per ounce in determining which is the better value....with that number being inaccurate, it can trick someone into thinking that one product cost less per ounce than a competing product. Is this a crime?...above my pay grade. Is it dishonest? Yes.
Again it makes no difference...call the ftc and file a complaint...maybe your lawyer can file a class action lawsuit and you can collect your 25 cents
Bruce
Supporting Founder Lifetime Supporter
Last reply · posted in Internet Television (IPTV) Discussion Forum
Comcast is the first to report, with a massive 274,000 loss in video subscribers.

In the 3Q of 2016, Comcast had 21.42 million video subscribers and was the #1 provider, now at 10.39 million and is the #3 Provider, YTTV is #2 ( who also surpassed DirecTV-8 Million and Dish-under 5 Million), Charter/Spectrum is #1.

4 Replies · 59 views
  • Like
Reactions: Howard Simmons
dishstaller
Losing 144,000 internet customers surprises me more.
S
Losing 144,000 internet customers surprises me more.
people are moving to fiber, which is better up and down and also not Comcast.
  • Like
Reactions: dishstaller
dishdude
people are moving to fiber, which is better up and down and also not Comcast.
Losing 144,000 internet customers surprises me more.

Cord cutting 2.0. Not just fiber, 5G is really taking a toll on the cable companies.
AZ.
AZ.
Cord cutting 2.0. Not just fiber, 5G is really taking a toll on the cable companies.
I agree, for $35 it aint perfect but just as reliable as my cable was. And that was twice as much and still rising
dishstaller
Pub Member / Supporter Lifetime Supporter
Last reply · posted in The Chit Chat Club
He was 71 yrs old. One of my favorite songs is Seminole Wind....the violin is killer.


View: https://www.youtube.com/watch?v=W8sh9P3X33w
9 Replies · 93 views
M
I Wish I Could Have Been There is an amazing song. Rest in peace Mr Anderson.
dishstaller
I Wish I Could Have Been There is an amazing song.
That's one of those songs that hits a little too close to home for me. I like the song but just can't listen to it. It's kinda like that song "Daddy never was the Cadillac kind".....reminds me too much of my Grandfather who died Feb 18, 1995.
  • Sad
  • Like
Reactions: Mr Tony and mikew
dfergie
R.I.P. I thought he was older…
M
R.I.P.
Got a few songs on my 'setup' (old cell phone with music) that I can listen to while working
S
RIP
KE4EST
R.I.P. I thought he was older…
Same here. I thought he was older......RIP
SuperDish_Fan23
Last reply · posted in DISH Network Support Forum
Why are ViP922s So rare? like its crazy how ebay has none, i checked everywhere, also, i got a ViP222k now, which is actually activated!
25 Replies · 632 views
S
That's not really unusual. Cable companies like to the provide the box too. The phone company provided the phones in until the government forced them to allow third-party phones.
  • Like
Reactions: charlesrshell
Almighty1
That's not really unusual. Cable companies like to the provide the box too. The phone company provided the phones in until the government forced them to allow third-party phones.
Yes, the Western Electric phones that says "Bell System Property, NOT FOR SALE, Western Electric".
Bobby
Yes, the Western Electric phones that says "Bell System Property, NOT FOR SALE, Western Electric".
In my very early work life I installed and repaired those phones.
AZ.
AZ.
Yes, the Western Electric phones that says "Bell System Property, NOT FOR SALE, Western Electric".
someone is showing their age
Almighty1
someone is showing their age
LOL. It depends if the person saw it during the years when they were actually still available which is 1968 to 1983 meaning the person could be 43-58 years old or they can even be a few years old if they learned to read and write at a young age and actually saw a telephone with that label somewhere recently just like even here in San Francisco, payphone still exist physically in public places but whether they can be used or not is a different issue. It still looks like this even today:
1792633296785.webp
  • Like
Reactions: charlesrshell
dishstaller
I opened my Radio Shack in Sept 1984 and right about that time they did the whole deregulation thing with the phone companies. I bought TONS of those phones that had been refurbished with a new outer shell. You could throw one of those out of a 3 story high window and it would still work.
That was an interesting time in history. I would have older customers come in and ask about phones.....they were terrified that they were going to get into trouble hooking up a second phone without the phone company knowing about it. One of the funniest episodes of WKRP was the one where Johnny thought the cops were showing up because they had an unregistered phone. I guess younger folks can't conceive of a time when you were limited to the number of phones you could have in your house....and limited to the length of the cord 🤣
llokey
In my very early work life I installed and repaired those phones.
And I kept them working through the ESS offices.
Bobby
And I kept them working through the ESS offices.
The two central offices in the area I worked were actually step by step offices. :)
  • Like
Reactions: charlesrshell
Almighty1
I opened my Radio Shack in Sept 1984 and right about that time they did the whole deregulation thing with the phone companies. I bought TONS of those phones that had been refurbished with a new outer shell. You could throw one of those out of a 3 story high window and it would still work.
That was an interesting time in history. I would have older customers come in and ask about phones.....they were terrified that they were going to get into trouble hooking up a second phone without the phone company knowing about it. One of the funniest episodes of WKRP was the one where Johnny thought the cops were showing up because they had an unregistered phone. I guess younger folks can't conceive of a time when you were limited to the number of phones you could have in your house....and limited to the length of the cord 🤣
Speaking about cords, I actually did drop a Trimline phone from probably 3 feet high on the floor when I was about 10 or so and it caused a small crack, this was the one with the modular jacks and it was hooked up with I think a 50 ft or longer RJ11C cable from Radio Shack. I still use the phone today connected to a Obi VoIP adapter and the cord is my custom made 6 position RJ11C, not sure of the official name for it without looking it up and Belden MediaTwist Crescent shaped Cat6+ cable.

1792686536450.webp
  • Like
Reactions: charlesrshell
S
LOL. It depends if the person saw it during the years when they were actually still available which is 1968 to 1983 meaning the person could be 43-58 years old or they can even be a few years old if they learned to read and write at a young age and actually saw a telephone with that label somewhere recently just like even here in San Francisco, payphone still exist physically in public places but whether they can be used or not is a different issue. It still looks like this even today:
View attachment 194957
so that persons in hiding lol:biggrin
  • Like
Reactions: charlesrshell
S
remembers when ATT had stores and leased home phones
  • Like
Reactions: charlesrshell