Social Feed
I bought a KBOX K2 Receiver on eBay and a GEOSatpro 90cm from Satellite AV and an extra dual LNB kit from them as well. Anyways, I have read every instruction and howto about this FTA stuff and am beating my head against the wall. No matter where I aim the dish, 97 degrees or 123 degrees, the best I can get is 47% signal and 47% quality, even if I aim the dish straight north or at a wall on my house the quality bars won't barely budge, 44% is low end, the best I got was 50% for a minute or so. Used dishpointer for the sat aiming settings, a compass to aim the dish, and all the frequency settings and such on the receiver are correct, referred to lyngsat for those. Used a RG6 25' cable straight from the receiver to the LNB. Tried a 2nd LNB as well to make sure 1st wasn't bad, tried another RG6 cable too. Kbox is un-modified, has factory flash of December, 2009? Just wondering if anyone else has used this equipment with luck?
4 Replies
·
2546 views
Pub Member / Supporter
Cutting Edge
WANTED DirecTV LCC
Anyone have a DirecTV Local Channel Connector that you'd like to get rid of at a reasonable price? DirecTV is currently in a contract dispute with owner of my local ABC affiliate.
12 Replies
·
288 views
I did that. The response was that the LCC is not available. Escalated the issue to a tech support person with the same results.
Could be out of them I guess ... I'd keep trying, every 3-4 days.I did that. The response was that the LCC is not available. Escalated the issue to a tech support person with the same results.
If they are not out of them as them WHY you can't get one, seeing Your in a Dispute. Thats what they are for.
I would make them give you a real answer, don't let them off the hook.
I had one, and it worked well, but I believe I gave it to another D* friend (also had a AM21), I know I gave them away ...
According to the tech support guy, they don't have any in stock. He said I should receive an email when and if they have them. I even told him I would accept a refurbished unit.
I'm not sure your going to find any Refurbished ones as D* doesn't ask for them back.According to the tech support guy, they don't have any in stock. He said I should receive an email when and if they have them. I even told him I would accept a refurbished unit.
Pub Member / Supporter
Lifetime Supporter
Did anyone have a price increase today on their equipment? I own my VIP211k's, and they have been $5.00. My bill that I received last week shows the "add-ons" as being $5.00. However, I just logged into my Dish account, and my "add-ons" are now $10.00. Did the additional receivers go up by $5.00 recently?
As I mentioned, my last bill shows $5.00 and under the notes, nothing is mentioned about a price increase.
As I mentioned, my last bill shows $5.00 and under the notes, nothing is mentioned about a price increase.
11 Replies
·
185 views
Hello everyone, new guy here. I'm trying to solve problem I'm having with Dish bonus view channels. When I'm watching the bonus view channels then I switch back to regular dish channels, after few minutes the screen flips to black and after 30 seconds flips back to regular channels and continues to flip back and forth until I turn off TV. After I wait 30 minutes and turn back on , I can use regular channels again. So, its after I switch from bonus view channels to regular dish channels the problem starts. Been trying to fix this for a month, but no luck
Here what I've done.
i contacted Dish support and they sent me a new Joey3, but no help. Switched to a different HDMI input on TV, no help. Used different HDMI cable , no help. Used different electrical wall plug, no help.
Finally got a Dish tech to check it. He ran all systems check and was OK. Finally he brought in a small TV and plugged in the HDMI out from the Joey to the small TV. He could not get the problem to occur on his small TV, so the new Joey was working OK. So, then the problem must be myTV. He made some phone calls and came back with the answer that there must be a problem with the analog to digital switch in my TV. Has anyone ever heard of a problem like this, or is it time to be looking for a new TV? My tv LG OLED65C8PUA. TV has been trouble free til now. Thanks
Here what I've done.
i contacted Dish support and they sent me a new Joey3, but no help. Switched to a different HDMI input on TV, no help. Used different HDMI cable , no help. Used different electrical wall plug, no help.
Finally got a Dish tech to check it. He ran all systems check and was OK. Finally he brought in a small TV and plugged in the HDMI out from the Joey to the small TV. He could not get the problem to occur on his small TV, so the new Joey was working OK. So, then the problem must be myTV. He made some phone calls and came back with the answer that there must be a problem with the analog to digital switch in my TV. Has anyone ever heard of a problem like this, or is it time to be looking for a new TV? My tv LG OLED65C8PUA. TV has been trouble free til now. Thanks
6 Replies
·
89 views
Staff member
HERE TO HELP YOU!
Cutting Edge
Sometimes a thread gets so many posts in it that is can cause issues for the server so that why today we introduce The Song Name Game Part 3!
So let the game continue!
The last song was added by Bobby who posted...
One Meat Ball - Andrews Sisters
CONTINUE ON AND HAVE FUN! WELCOME HOME TO SATELLITEGUYS.US!
Here are the original rules for the game as posted by WebbyDude back in 2006. http://www.satelliteguys.us/threads/68645-Song-Name-Game
Just name a song title and the band who performed it. The next person does the same thing, but needs to list a song title or band name which includes a word from the previous entry. Pick songs from any genre.
Example:
Long Live Rock and Roll -- Rainbow
Rainbow in the Dark -- Dio
Another example:
Ride the Lightning -- Metallica
Lightning Strikes -- Ozzy Osbourne
Get it?
An additional note: we all know that song titles, sometimes, use profane words. Because this is a family friendly website it is advised that you clean up that title up a bit. This is accomplished by using something like sh!t instead of the real word. Thanks....
So let the game continue!
The last song was added by Bobby who posted...
One Meat Ball - Andrews Sisters
CONTINUE ON AND HAVE FUN! WELCOME HOME TO SATELLITEGUYS.US!
Here are the original rules for the game as posted by WebbyDude back in 2006. http://www.satelliteguys.us/threads/68645-Song-Name-Game
Just name a song title and the band who performed it. The next person does the same thing, but needs to list a song title or band name which includes a word from the previous entry. Pick songs from any genre.
Example:
Long Live Rock and Roll -- Rainbow
Rainbow in the Dark -- Dio
Another example:
Ride the Lightning -- Metallica
Lightning Strikes -- Ozzy Osbourne
Get it?
An additional note: we all know that song titles, sometimes, use profane words. Because this is a family friendly website it is advised that you clean up that title up a bit. This is accomplished by using something like sh!t instead of the real word. Thanks....
67109 Replies
·
2662355 views
Staff member
HERE TO HELP YOU!
House of the Dragon, the prequel to Game of Thrones, premieres on HBO Max on 8/21. I will be warching
www.syfy.com
View: https://youtu.be/fNwwt25mheo
S~
'Game of Thrones' spinoff 'House of the Dragon' fires up release date at HBO, drops new character pics
The wait’s felt a little like watching for a dragon egg to hatch, but HBO’s hugely anticipated Game of Thrones prequel series finally has a release date. House of the Dragon will debut the first of its initial 10-episode season this summer, the network revealed today in a series of tweets that...
View: https://youtu.be/fNwwt25mheo
S~
39 Replies
·
5640 views
TWiT Tech Podcast Network
Time for another AWESOME video from the TWIT Network!
View: https://www.youtube.com/watch?v=unH0Z1jl228
Direct YouTube Link - Why New FCC Rules Could Crush Phone Privacy in the US
TWIT's Website
TWIT Live Feed
View: https://www.youtube.com/watch?v=unH0Z1jl228
Direct YouTube Link - Why New FCC Rules Could Crush Phone Privacy in the US
TWIT's Website
TWIT Live Feed
0 Replies
·
5 views
Hi all, I recently inherited a FTA system off Craiglist and have been trying to get it set up. What I got was a Glorystar-branded ~90cm offset dish with a ground mount (/flat roof) frame, and GEOSATpro DSR200c receiver. From that initial equipment, I've replaced the old LNBF with a (cheap!) new one and also splurged on an SG-2100 H-H motorized rotor which does respond from the receiver's USALS menu.
The previous owner had it set up for religious programming on Galaxy 19 and I've been trying to start by finding that same bird at least. After a couple sessions I'm not sure I have, but I've found *something* at least! A handful of motor ticks further than the dish wants to be for 97W after starting from motor 0 pointing as much south as I can guess at. (I don't have great references to aim for and it's really hard to sight where exactly the dish is pointing anyway….)
Anyway, so far there's only one transponder that I've ever been able to catch as I search. It's 12146 V and when the receiver scans it I get this list of video channels:
but it's a long-winded spiel about "you know us as an industry-leading satellite solutions provider with over a quarter million sites" and to call them For All Your Every Needs™ type thing.
While I get little blips from other frequencies, this is the only strong transponder I've been able to come across. My receiver shows it as S 75 and Q up to 85 when I adjust it. It actually seemed to get better as I **un**skewed my LBNF — iiuc G19 was supposed to be -20º for me but however I'm supposed to be reading/referencing the angles the puck is now basically at 0º relative to the dish/arm got the strongest on this transponder.
Anyway sorry this is so long winded already… my question is, do I even have the right satellite? None of the other transponders that are supposed to be active on G-19 seem to come in. And if not the right satellite does anyone happen to recognize which one I might have found instead? I think knowing that would help me then adjust for a truer south aim and then hopeful the USALS will work automatically once I can get it dialed in.
The previous owner had it set up for religious programming on Galaxy 19 and I've been trying to start by finding that same bird at least. After a couple sessions I'm not sure I have, but I've found *something* at least! A handful of motor ticks further than the dish wants to be for 97W after starting from motor 0 pointing as much south as I can guess at. (I don't have great references to aim for and it's really hard to sight where exactly the dish is pointing anyway….)
Anyway, so far there's only one transponder that I've ever been able to catch as I search. It's 12146 V and when the receiver scans it I get this list of video channels:
- 1.1 Srv_1
- 2.84 OU_Chan
- 3.2 Srv_2
- 4.5 Srv_5
- 5.3 Srv_3
- 6.4 Srv_4
- 7.6 Srv_6
- 8.7 Srv_7
but it's a long-winded spiel about "you know us as an industry-leading satellite solutions provider with over a quarter million sites" and to call them For All Your Every Needs™ type thing.While I get little blips from other frequencies, this is the only strong transponder I've been able to come across. My receiver shows it as S 75 and Q up to 85 when I adjust it. It actually seemed to get better as I **un**skewed my LBNF — iiuc G19 was supposed to be -20º for me but however I'm supposed to be reading/referencing the angles the puck is now basically at 0º relative to the dish/arm got the strongest on this transponder.
Anyway sorry this is so long winded already… my question is, do I even have the right satellite? None of the other transponders that are supposed to be active on G-19 seem to come in. And if not the right satellite does anyone happen to recognize which one I might have found instead? I think knowing that would help me then adjust for a truer south aim and then hopeful the USALS will work automatically once I can get it dialed in.
9 Replies
·
264 views
Done and done and done! I ended up doing a bit more iteration (back and forth between the left-right and up-down adjustments) but I've now got it landing on G19 at its default position for 97W.
Yep, ended up with a page or two full on my receiver's search. Didn't double-check that my receiver has all six of the right transponders but I can mess with that later if it turns out I'm missing something interesting but still DVB-S / MPEG-2 compatible.
Yep, can see definite signal degradation as soon as I skew the LNB either way from "straight" (seam on the LNB lined up with the clamps on the mounting bracket). Will make setup easier if I want to try swapping anything else in!
I don't know if there's any good (unencrypted, DVB-S) satellite farther away to really check the sweep against, but I was at least able to program in my original find at 101.0 W back in (now at the correct "12000 V 20000" setting) and can get both birds automatically.
Shouldn't be *that* exciting since it's just an ad, but still really fun to choose channels on the other one and have it jog over and lock on
B
beside 123W, another one to try (if it's above the horizon at your location) is Hispasat @30W. It has at least 2 DVB-S transponders with SD/Mpeg2 channelsDone and done and done! I ended up doing a bit more iteration (back and forth between the left-right and up-down adjustments) but I've now got it landing on G19 at its default position for 97W.
Yep, ended up with a page or two full on my receiver's search. Didn't double-check that my receiver has all six of the right transponders but I can mess with that later if it turns out I'm missing something interesting but still DVB-S / MPEG-2 compatible.
Yep, can see definite signal degradation as soon as I skew the LNB either way from "straight" (seam on the LNB lined up with the clamps on the mounting bracket). Will make setup easier if I want to try swapping anything else in!
I don't know if there's any good (unencrypted, DVB-S) satellite farther away to really check the sweep against, but I was at least able to program in my original find at 101.0 W back in (now at the correct "12000 V 20000" setting) and can get both birds automatically.
Shouldn't be *that* exciting since it's just an ad, but still really fun to choose channels on the other one and have it jog over and lock on
No luck finding this one. I motor over and it seems like a pretty dead spot of sky. I did get a slight blip (Q up to 1% or 2%) if I lowered the dish slightly. So I wonder if my polar mount itself maybe needs a bit of fine tuning?
Even when loosening the bolts and manually nudging the dish up/down/left/right nothing seemed to really wake it [new receiver, see below!] up and never saw anything more than 4% or 5% which I don't know is even real or could have been just noise?
I'm in Washington state (northwest CONUS) so this one's not an option for me.
I now have a V8 Finder 2
I've been able to scan in more now on G-19, and as well as watching the ad on SES 1 and getting some PBS stations there and G-16 both. So three satellites kinda in the general vicinity of each other (97W/101W/99.1W) programmed and able to rotate between.
Is G-18 at 123W as strong as the others? According to Satbeams I should be at least somewhat in its footprint although it looks like it's maybe focused more on Alaska.
Now that I'm back at my computer waiting for the Finder to charge back up looks like the Eutelsat(s) 117W have a couple Ku transponders I could look for too.
TWiT Tech Podcast Network
Time for another AWESOME video from the TWIT Network!
View: https://www.youtube.com/watch?v=wW3qReY-JYA
Direct YouTube Link - Google's New Translate Tool
TWIT's Website
TWIT Live Feed
View: https://www.youtube.com/watch?v=wW3qReY-JYA
Direct YouTube Link - Google's New Translate Tool
TWIT's Website
TWIT Live Feed
0 Replies
·
9 views
TWiT Tech Podcast Network
Time for another AWESOME video from the TWIT Network!
View: https://www.youtube.com/watch?v=-zh1RgcJue0
Direct YouTube Link - Another Cisco SD-WAN 0-day?
TWIT's Website
TWIT Live Feed
View: https://www.youtube.com/watch?v=-zh1RgcJue0
Direct YouTube Link - Another Cisco SD-WAN 0-day?
TWIT's Website
TWIT Live Feed
0 Replies
·
6 views
I'm having trouble finding a for sure answer on this. When I first started diving back into satellite stuff I noticed the GT Media V8 Finder2 which looks pretty cool and relatively low price point. But I can't find an answer, seems like some people (and Amazon's own AI guesser-bot) say it doesn't support motors.
The manual itself (the PDF that I found is named 20220718043903GTMEDIAV8FINDER2.pdf and it's on page 6 of 8) does show on the installation screen a "Motor Setup" menu item and says "If select DiSEqC1.2 or USALS, we can press ◀︎▶︎ to select IF Channel, and use number key to input Center Frequency."
Which…… the USALS part seems promising, but I don't know what IF and Center frequencies have to do with anything? Can it drive the motor off its battery for one, and does it have options for e.g. using the ◀︎▶︎ arrows to change the aim and save adjustments?
The closest I've found to real-world experience here is in Long shot with TBS6909X card where someone is talking about a different rotor and says:
> when I connect my V8 Finder 2, it immediately moves the dish if it's not in the correct position
which seems really promising! Moving the dish is what I'm after here, with something newer than the old MPEG-2 receiver I have now. Even for other receivers its really unclear if motor support is just pretty much a safe assumption that they don't even mention it anymore?
The V9 Prime actually looks pretty nice too and assuming it runs motors maybe that'd be better than the V8 Finder 2 for actual long term use since it has networking. But I'm having trouble finding listings for it (and actually most other receivers I see mentioned here) on Amazon or eBay or even Aliexpress. I'm wanting a DVB-S2 receiver for at least MPEG-4 with H.264/AVC and maybe should just get H.265/HEVC while I'm shopping. Main criteria:
* run my "Goto X"-era SG-2100 rotator
* be able to view most/all modern FTA satellites
* ideally a scheduled DVR feature and/or network would make it more useful
* I don't mind if it has… "alternative" firmwares or features but just for broader compatibility/interest
My main goal is I guess just exploration, seeing what's up there. Honestly not a big TV guy and definitely not into infomercials but if I can time shift the occasional Bob Ross or Mr. Rogers Neighborhood, or catch some world events as they're being uplinked, that sort of thing might be interesting. (Honestly main goal started out as weather satellites but this is kinda a warmup excercise for what will likely be a separate setup due to the frequencies.)
My dish is kinda far from my house and even farther from my "radio shack" so if I could just run a PoE ethernet line to something in a box below the dish, or a coax only to the crawlspace where I have 110V but either way would need it full remote including changing between satellites. To avoid having to buy and pull tons more coax up and down through the house. I'm into open source and real standards, so I'd much rather something that I can say use with VLC or go2rtc via a raw IP address and protocol rather than some convenient but proprietary iOS cloud app thingy.
The manual itself (the PDF that I found is named 20220718043903GTMEDIAV8FINDER2.pdf and it's on page 6 of 8) does show on the installation screen a "Motor Setup" menu item and says "If select DiSEqC1.2 or USALS, we can press ◀︎▶︎ to select IF Channel, and use number key to input Center Frequency."
Which…… the USALS part seems promising, but I don't know what IF and Center frequencies have to do with anything? Can it drive the motor off its battery for one, and does it have options for e.g. using the ◀︎▶︎ arrows to change the aim and save adjustments?
The closest I've found to real-world experience here is in Long shot with TBS6909X card where someone is talking about a different rotor and says:
> when I connect my V8 Finder 2, it immediately moves the dish if it's not in the correct position
which seems really promising! Moving the dish is what I'm after here, with something newer than the old MPEG-2 receiver I have now. Even for other receivers its really unclear if motor support is just pretty much a safe assumption that they don't even mention it anymore?
The V9 Prime actually looks pretty nice too and assuming it runs motors maybe that'd be better than the V8 Finder 2 for actual long term use since it has networking. But I'm having trouble finding listings for it (and actually most other receivers I see mentioned here) on Amazon or eBay or even Aliexpress. I'm wanting a DVB-S2 receiver for at least MPEG-4 with H.264/AVC and maybe should just get H.265/HEVC while I'm shopping. Main criteria:
* run my "Goto X"-era SG-2100 rotator
* be able to view most/all modern FTA satellites
* ideally a scheduled DVR feature and/or network would make it more useful
* I don't mind if it has… "alternative" firmwares or features but just for broader compatibility/interest
My main goal is I guess just exploration, seeing what's up there. Honestly not a big TV guy and definitely not into infomercials but if I can time shift the occasional Bob Ross or Mr. Rogers Neighborhood, or catch some world events as they're being uplinked, that sort of thing might be interesting. (Honestly main goal started out as weather satellites but this is kinda a warmup excercise for what will likely be a separate setup due to the frequencies.)
My dish is kinda far from my house and even farther from my "radio shack" so if I could just run a PoE ethernet line to something in a box below the dish, or a coax only to the crawlspace where I have 110V but either way would need it full remote including changing between satellites. To avoid having to buy and pull tons more coax up and down through the house. I'm into open source and real standards, so I'd much rather something that I can say use with VLC or go2rtc via a raw IP address and protocol rather than some convenient but proprietary iOS cloud app thingy.
3 Replies
·
125 views
Thanks, great tips and yeah when I'd read how the H/V bias worked I wondered if the higher voltage was ever useful for better power transfer
It was perhaps slightly impulsive (though I guess not too late to cancel) but instead of the Finder unit I ended up going for kinda the opposite: a completely faceless USB tuner box (TBS5930) which should have RF support all the way up through DVB-S2X. If I'm understanding correctly the actual video/audio will then be whatever I can get software/GPU support for so my hope is that any unencrypted MPEG-2/AVC/HEVC feed can be viewed with VLC or whatnot. As well as access to what I assume is pure data like the Blockstream stuff just for example. (They had a lot of good resources for reception of their own signal in lots of various interesting ways and is kinda how I found the TBS options.)
And I think I will be able to control DiSEqC stuff through Linux including motor commands. So the idea is kinda what I mentioned, hoping this can just get chained in to an old thin client PC or if there's any Raspberry Pi that doesn't cost triple digits these days, somewhere physically convenient and then run it all over LAN from my laptop.
All this is somewhat theoretical of course based on what I'm piecing together but at a certain point I usually have to close all the browser tabs and just commit to try *something* that looks promising and go from there.
It was perhaps slightly impulsive (though I guess not too late to cancel) but instead of the Finder unit I ended up going for kinda the opposite: a completely faceless USB tuner box (TBS5930) which should have RF support all the way up through DVB-S2X. If I'm understanding correctly the actual video/audio will then be whatever I can get software/GPU support for so my hope is that any unencrypted MPEG-2/AVC/HEVC feed can be viewed with VLC or whatnot. As well as access to what I assume is pure data like the Blockstream stuff just for example. (They had a lot of good resources for reception of their own signal in lots of various interesting ways and is kinda how I found the TBS options.)
And I think I will be able to control DiSEqC stuff through Linux including motor commands. So the idea is kinda what I mentioned, hoping this can just get chained in to an old thin client PC or if there's any Raspberry Pi that doesn't cost triple digits these days, somewhere physically convenient and then run it all over LAN from my laptop.
All this is somewhat theoretical of course based on what I'm piecing together but at a certain point I usually have to close all the browser tabs and just commit to try *something* that looks promising and go from there.