Social Feed

S
Last reply · posted in DISH Network Support Forum
I'd like to receive all of the HD channels available because I currently do not receive TruTV HD, G4 HD, or a couple of others.

My two receivers are a VIP622 and a 625.

---

I've just checked my roof and I two Dish 500 satellite dishes.

System Information shows satellites 119, 110, and 61.5 under the "g" section. (all have green blocks underneath them)

The Point Dish screen gives me these values:

Satellite 110 = 75 strength
Satellite 119 = 92 strength
Satellite 61.5 = 59 strength

Other satellites also give me values (eg. 148) but others do not get any signal at all.

---

According to technical support I can have a new dish installed but it will require upgrading my 625 and thus a new 2-year contract. That seems a bit harsh seeing how I am already paying for TV stations that I am not receiving.

What options do I have?
37 Replies · 4788 views
H
Northeastern PA is NY RSN's

129 is useless to us here.
With a look angle of 18 degrees don't count on tuning it.

You either need to Go 100% Eastern Arc, (1000.4) Meaning get your Equipment upgrade, or suffer with the Missing HD channels.
Also what County are you in?
This is also important.
M
Northeastern PA is NY RSN's

129 is useless to us here.
With a look angle of 18 degrees don't count on tuning it.

18 elevation isnt that bad. When 148 was active that was a 16 elevation for me in Minneapolis and had no issues

I would say try it. Worse thing that can happen is it doesnt come in then you move the dish back to 61.5
H
I would say try it. Worse thing that can happen is it doesnt come in then you move the dish back to 61.5
This is whats going to happen.:)
If the 129 was accessable in the Northeast with such ease, E* would have never made us use Wing dishes pointed at the 61.5 for years before Eastern Arc came around.
K
Recently had the same situation. East Coast (west coast of FL) and all my locals were coming off 61.5. Since I pay the equipment protection fee, a new dish only cost me $15. The installer gave me two options: Eastern Arc (EA) or Western Arc. Either way it was a one dish solution. EA dish is larger and could only be mounted on the roof. WA could be mounted on an existing pole bolted on fascia. That was no brainer-keep existing mount. Even with WA, I still receive all SD and HD locals.

It must be very difficult to tune the new WA dish, because a second technician had to come out to re-point it. He said it was off by a hair. Just enough that wind caused pixelation.

If you have never pointed a dish before, it is worth paying to have a pro do it. It will take 2 or more hours to point manually. And that is only if you have someone else watching the receiver meter.
Jimmerinwi
Recently had the same situation. East Coast (west coast of FL) and all my locals were coming off 61.5. Since I pay the equipment protection fee, a new dish only cost me $15. The installer gave me two options: Eastern Arc (EA) or Western Arc. Either way it was a one dish solution. EA dish is larger and could only be mounted on the roof. WA could be mounted on an existing pole bolted on fascia. That was no brainer-keep existing mount. Even with WA, I still receive all SD and HD locals.

It must be very difficult to tune the new WA dish, because a second technician had to come out to re-point it. He said it was off by a hair. Just enough that wind caused pixelation.

If you have never pointed a dish before, it is worth paying to have a pro do it. It will take 2 or more hours to point manually. And that is only if you have someone else watching the receiver meter.
Eastern Arc can be mounted on a pole, or facia mount. It does have a heavier thicker guage mast that has to be used, can't use the trditional 500 or 1000.2 mast, it isn't strong enough. I think the installer you had was not real educated on this. Saying that EA can only be mounted on a roof was nothing close to the truth. There are many different mounting options for the eastern arc dish, not just roofs.
As far as tuning a wa dish, if you have the right equipment, which I assume someone working for Dish or even a sub doing this for a living should have, it is actually easy to tune. I think the guy you had was a moron!! JMHO
icon7.gif
sca
sca
This is whats going to happen.:)
If the 129 was accessable in the Northeast with such ease, E* would have never made us use Wing dishes pointed at the 61.5 for years before Eastern Arc came around.

NOT true at all. there are lots of markets with good access to 129 that have locals on 61.5.
M
I dont get why the OP doesnt at least TRY to get 129 before throwing in the towel and having Dish upgrade (and extend his commitment) to EA
M
NOT true at all. there are lots of markets with good access to 129 that have locals on 61.5.

also 129 was crap when it was Echo 5
sca
sca
also 129 was crap when it was Echo 5

agreed. but its great now IMHO. he probably hasnt tried the 129 because the csr said 'no'. as you and i know the csr he talked to was just telling him what he needed to have based on what the computer told HER. i think he should let the tech show up and take it from there.
maybe, just call in a tech visit without setting up an ea upgrade...
H
NOT true at all. there are lots of markets with good access to 129 that have locals on 61.5.
Not in Northeastern Pa or New england states.
By all means try it, But 18 Degrees make Line of sight an issue around these parts. If he lives in a wide open field over looking a vally, most lilky he'll get it. But anyone that lives in Northeaster Pa, knows this is not common.
Better mount it on the peak of your roof.
S
I dont get why the OP doesnt at least TRY to get 129 before throwing in the towel and having Dish upgrade (and extend his commitment) to EA
I've never pointed a dish before so I'm not really sure what's involved. I'm also a bit worried that after moving the dish I won't be able to set it back to where it was and then I'll be without satellite for several days.

I might take my chances with a tech visit, but it seems like the techs only do what's on their work order and if it says to install a 1004 dish I wonder if they would even have an extra Dish 500/1002 to even try. :(
K
Eastern Arc can be mounted on a pole, or facia mount. It does have a heavier thicker guage mast that has to be used, can't use the trditional 500 or 1000.2 mast, it isn't strong enough. I think the installer you had was not real educated on this. Saying that EA can only be mounted on a roof was nothing close to the truth. There are many different mounting options for the eastern arc dish, not just roofs.
As far as tuning a wa dish, if you have the right equipment, which I assume someone working for Dish or even a sub doing this for a living should have, it is actually easy to tune. I think the guy you had was a moron!! JMHO
icon7.gif
Maybe if I did not live in a tropical storm/HURRICANE zone that might be acceptable. It was something about dish size and wind speed. Winds caused picture break up and they were not even near what I call high winds. They were more adjust you swing a little winds. I could still cast a Clouser or a Turneffe Crab 70' in those winds, if only the water was a little warmer. - that was a plug endorsing burning of oil in the Gulf.

And it would be easy to adjust if you had a good meter.
M
I've never pointed a dish before so I'm not really sure what's involved. I'm also a bit worried that after moving the dish I won't be able to set it back to where it was and then I'll be without satellite for several days.
if you goof up all you'd be out would be 61.5

It really isnt that hard to do. If you want to try it, just make sure you remember what the elevation is of the dish for 61.5. Also make a mark on the mast of the dish so if it doesnt work you can reline up the dish for 61.5

If you want to pursue it, let us know and we can give some detailed instructions :)


I might take my chances with a tech visit, but it seems like the techs only do what's on their work order and if it says to install a 1004 dish I wonder if they would even have an extra Dish 500/1002 to even try. :(

they could just try and reaim the 61.5 dish to 129 that is on the roof.
Peter Parker
Supporting Founder Lifetime Supporter
Last reply · posted in DISH Network Support Forum
No idea what improvements might be involved.
13 Replies · 603 views
  • Like
Reactions: LQQK and reubenray
Almighty1
Updated to H713 on a Hopper 3 from H712 with Hopper Plus a few hours earlier.

It brought a old problem back:

One of the problems I am seeing is that the Available Joey Software section no longer is showing the Android TV versions even after a manual software reset twice and the nightly reboot. Until it does, nether Technician Android TV download and Hopper Plus is able to check, download and update the Android TV software.

This was a major problem with H703.

H710 removed that dependency but it's broken again.

Rick Durham and brittanygarden
  • Like
Reactions: charlesrshell
Almighty1
Updated to H713 on a Hopper 3 from H712 with Hopper Plus a few hours earlier.

It brought a old problem back:

One of the problems I am seeing is that the Available Joey Software section no longer is showing the Android TV versions even after a manual software reset twice and the nightly reboot. Until it does, nether Technician Android TV download and Hopper Plus is able to check, download and update the Android TV software.

This was a major problem with H703.

H710 removed that dependency but it's broken again.

Rick Durham and brittanygarden

Within the last few hours as I did check earlier today when it was still missing, the Available Joey Software line now has added "P154 P15403" which is for the Hopper Plus that I have but my Hopper Plus software is still on P15317, I will do a Download Android TV (ATV) Software for the Hopper Plus, Joey 4 and Wireless Joey which are all Android TV devices and then manually do a check update on the Hopper Plus to update the software shortly.
  • Like
Reactions: charlesrshell
BatStang2000
This happened to me. I was outside mowing and my wife came out and said that our nieces and nephews were going to be on the Noon News. She had it on in the bedroom on our Joey3. Since they weren't on yet, I decided to turn it on in the Living Room on our Hopper3. When I selected the channel (through Dish, not OTA) the Joey3 turned itself off. When I went back to the bedroom to turn it back on, the Hopper3 did a reboot. Luckily it all finished before their story came on, but I just found it strange.
bookworm370
Has anyone noticed an FF stutter with 713? I used to be able to hit FF a few times and skip smoothly. After 713 (maybe 712), when I skip forward, there is a definite stutter for as many times as I have pressed FF.

Can anyone check on this and report back? Recorded programs and then press skip forward a few times to see if it's smooth? Normally, it just jumps to the right place after the skips.
  • Like
Reactions: charlesrshell
R
I got the 713 update yesterday.
  • Like
Reactions: charlesrshell
N
I'm getting fabulous picture on Ch. 148 4k, but zero audio with H713. This is with a recorded show (Notre Dame game). Anyone else have this? Audio is fine on every other channel.
brittanygarden
Staff member Pub Member / Supporter
Last reply · posted in DISH Network Support Forum
Please post your remote make/model here and any details of your issue. We are looking to collect as many examples as possible. I may reach out to you for your receiver number, but please do not post it here.

If you've already reported this to me, please repost it here so I can track all instances in one thread.

Thanks!
Brittany
24 Replies · 732 views
bookworm370
I have a solution that is guaranteed to work.
All Hopper developers are required to turn in their RF Hopper remotes and use only IR remotes.

I guarantee you that the bug will be fixed in two days!
Try it; it will work! They will work 24 hours a day to fix it when the WAF goes into the toilet!
GRB1959
I have a solution that is guaranteed to work.
All Hopper developers are required to turn in their RF Hopper remotes and use only IR remotes.

I guarantee you that the bug will be fixed in two days!
Try it; it will work! They will work 24 hours a day to fix it when the WAF goes into the toilet!
Excellent suggestion.
Foxbat
I think I have a separate issue with our Hopper 3 when watching/recording a 4K event. I have had many instances of it spontaneously restarting when I "disturbed" it during a 4K event. I learned to not touch the remote after a given point.

But it might be the IR code subroutine and 4K that make it touchy. I'll try it Wednesday night during the NLCS Game 3.
  • Like
Reactions: charlesrshell
JeffN9
I think I have a separate issue with our Hopper 3 when watching/recording a 4K event. I have had many instances of it spontaneously restarting when I "disturbed" it during a 4K event. I learned to not touch the remote after a given point.

But it might be the IR code subroutine and 4K that make it touchy. I'll try it Wednesday night during the NLCS Game 3.
I was having similar issues last night while watching and recording the NLCS game on 148. When I tried resuming the game at one point the screen went blank and I couldn't get my H3 to respond to any remote commands. Eventually the Hopper went to a HD channel but still no remote response. After a while the Hopper went into a re-boot cycle. This happened at least 3 times. I was using an IR universal remote only.

A little frustrating to have the game broken up like that but at least the Brewers won:)
bookworm370
Excellent suggestion.
Yea, I've only been a CIO for the last 30 years! :)
Trust me, when something important breaks, they get to own it!
A
Loaded H713 software on my Hopper 3 last week. Have not seen any change in the IR/RF remote issues with my Harmony 700.
Has Dish acknowledged this is a problem and are they committed to fixing it?
I'd be happy to roll back to last July.
long_time_Dish
Loaded H713 software on my Hopper 3 last week. Have not seen any change in the IR/RF remote issues with my Harmony 700.
Has Dish acknowledged this is a problem and are they committed to fixing it?
I'd be happy to roll back to last July. <-----|
Absolutely!!!---------------------------------------------|
Scott Greczkowski
Staff member HERE TO HELP YOU! Cutting Edge
Last reply · posted in The Chit Chat Club
Sometimes a thread gets so many posts in it that is can cause issues for the server so that why today we introduce The Song Name Game Part 3!

So let the game continue!

The last song was added by Bobby who posted...

One Meat Ball - Andrews Sisters

CONTINUE ON AND HAVE FUN! WELCOME HOME TO SATELLITEGUYS.US!

Here are the original rules for the game as posted by WebbyDude back in 2006. http://www.satelliteguys.us/threads/68645-Song-Name-Game

Just name a song title and the band who performed it. The next person does the same thing, but needs to list a song title or band name which includes a word from the previous entry. Pick songs from any genre.

Example:

Long Live Rock and Roll -- Rainbow

Rainbow in the Dark -- Dio

Another example:

Ride the Lightning -- Metallica

Lightning Strikes -- Ozzy Osbourne


Get it?


An additional note: we all know that song titles, sometimes, use profane words. Because this is a family friendly website it is advised that you clean up that title up a bit. This is accomplished by using something like sh!t instead of the real word. Thanks....
68516 Replies · 2671880 views
  • Like
Reactions: c-spand
long_time_Dish
In Time - Kit Watkins
dishstaller
Time In a Bottle - Jim Croce
  • Like
Reactions: long_time_Dish
EatMyVolts
No Time -- The Guess Who
dishstaller
The Devil Went Down to Georgia - Charlie Daniels
long_time_Dish
Down On My Knees - Bread
J
Last reply · posted in DISH Network Support Forum
This started a couple months ago. I have 2 H3s on one network, both with 2 EHD identical 3 TB seperately powered so all recordings are accessible by all 4k & J4s (8 of them).

On one H3 (not the main one that controls the MOCA network), after it reboots, it doesn't recognize it has two EHDs plugged into it. Rebooting the EHD by their power source doesn't fix it. Resetting the network doesn't. Software h3 reset doesn't fix it. Rebooting MOCA h3 doesn't fix it but so far, after 3+ cold boots (unplug pwr to H3 with unrecognized EHDs), it finally it figures out they are plugged into it. BUT.... Then when you open a program it only partially shows series and episodes, but instead of showing recordings, it only shows upcoming airings. HELP!!!!
23 Replies · 326 views
Almighty1
Thanks JohnGalt1234 - That's interesting. I wonder are the Boot Strap versions different between a Hopper 3 only and a Hopper 3 with Hopper Plus setup as I have the later. I guess when charlesrshell is able to since he has both setups, he can do the test. Unless the bootstrap version is tied to when the specific Hopper 3 is manufactured, in my case, mines is from February 2016 when it was installed.

At least Google Search AI is saying the bootstrap version will never change and unique to each Hopper 3.

1792277626286.webp


This is probably why different people seem to either have the issue or they don't because the bootstrap code could also be tied to the hardware revision and
components other than the internal HD.
  • Like
Reactions: charlesrshell
J
Sorry about dupe images... having a heck of a time trying to post an image of other H3 that my gf text to me.
  • Like
Reactions: charlesrshell
J
Sorry about dupe images... having a heck of a time trying to post an image of other H3 that my gf text to me.
1000013035.webp
  • Like
Reactions: charlesrshell
J
Thanks JohnGalt1234 - That's interesting. I wonder are the Boot Strap versions different between a Hopper 3 only and a Hopper 3 with Hopper Plus setup as I have the later. I guess when charlesrshell is able to since he has both setups, he can do the test. Unless the bootstrap version is tied to when the specific Hopper 3 is manufactured, in my case, mines is from February 2016 when it was installed.

At least Google Search AI is saying the bootstrap version will never change and unique to each Hopper 3.

View attachment 194853

This is probably why different people seem to either have the issue or they don't because the bootstrap code could also be tied to the hardware revision and
components other than the internal HD.
The image I just sent for master H3 is on hopper+., casino is not but both Vs and bootstraps are the same.
  • Like
Reactions: charlesrshell
Almighty1
JohnGalt1234 - So you basically have 2 Hopper 3's. The CasinoH3 is the one that is Hopper 3 only while Master Bedroom is a Hopper 3 with Hopper Plus setup.
Master Bedroom uses Android TV (ATV) software so the DISH part is actually a app and will behave differently as you can probably tell the Guide's are different on the Master Bedroom which will resemble the same guide used on other ATV devices such as the Joey 4 and Wireless Joey 4. If I am correct, the CasinoH3 is the one with the problem since you did say the one dated 09/05/2026 is the naughty one while 08/15/2026 named Master Bedroom is the nice one. Usually I would expect the CasinoH3 to be the one without the problem because it's Hopper 3 only and Master Bedroom would be the one with problems because it has the Hopper Plus involved. That is why they behave differently because CasinoH3 is running the native Hopper 3 software while Master Bedroom is running the Android TV software and also it runs a app called DISH known as package com.dish.atv.launcher, the version for mines is P15403 2026100917 so it's probably the same version as the Hopper Plus software version with the date of October 9, 2026, not sure what the 17 means except maybe revision 17?

This explains it better than I can. Sorry, had to take all the ads out.

1792279578261.webp
  • Like
Reactions: charlesrshell
J
JohnGalt1234 - So you basically have 2 Hopper 3's. The CasinoH3 is the one that is Hopper 3 only while Master Bedroom is a Hopper 3 with Hopper Plus setup.
Master Bedroom uses Android TV (ATV) software so the DISH part is actually a app and will behave differently as you can probably tell the Guide's are different on the Master Bedroom which will resemble the same guide used on other ATV devices such as the Joey 4 and Wireless Joey 4. If I am correct, the CasinoH3 is the one with the problem since you did say the one dated 09/05/2026 is the naughty one while 08/15/2026 named Master Bedroom is the nice one. Usually I would expect the CasinoH3 to be the one without the problem because it's Hopper 3 only and Master Bedroom would be the one with problems because it has the Hopper Plus involved. That is why they behave differently because CasinoH3 is running the native Hopper 3 software while Master Bedroom is running the Android TV software and also it runs a app called DISH known as package com.dish.atv.launcher, the version for mines is P15403 2026100917 so it's probably the same version as the Hopper Plus software version with the date of October 9, 2026, not sure what the 17 means except maybe revision 17?

This explains it better than I can. Sorry, had to take all the ads out.

View attachment 194857
As I understand it, the android is just the display signal from the hopper+. I can disconnect the H+ and plug the hdmi directly into the master hopper3.
  • Like
Reactions: charlesrshell
Almighty1
As I understand it, the android is just the display signal from the hopper+. I can disconnect the H+ and plug the hdmi directly into the master hopper3.
It is not just a display signal as explained above. When you have the Hopper+ connected, it uses Android TV for pretty much everything except for the satellite signal which is why it uses the DISH app for the standard Hopper 3 functions. But that should not matter because in your case, CasinoH3 is the Hopper 3 with the EHD which is what you call the naughty one based on the dates you mentioned and Master Bedroom which has the Hopper Plus connected to the Hopper 3 that does not have the problem. So one way to test the theory is disconnect the Hopper Plus from that Hopper 3 and then use the EHD's connected to CasinoH3 currently to see if the same issue exists. That way you will know if the problem is there without a Hopper Plus connected or if CasinoH3 is just a bad hopper to begin with.

Normally when you disconnect the Hopper Plus, it will be 30 minutes or more before you can use the Hopper 3 again.

What you want to do is:
hold the POWER button in, not the red reset button, for about 45 seconds or so while disconnecting the power to the Plus and moving the HDMI cable and it will reboot to the normal Hopper only immediately.
Ramy
Supporting Founder
Last reply · posted in The Sports Section
Really excited for this season with Kentucky having a new coach and some really exciting recruits. Probably won't last long, but here's hoping this season is great.
146 Replies · 1584 views
  • Haha
Reactions: Mike0616
Y
24 team playoff seems to be real close.

Are we really that far from a 64-team tournament?

The benefit of the 24 team playoff:
  • All the cartel teams that cartels want in playoff are in playoff
    • Independent of record too! Bonus.
  • MONEY!!!!! for the cartels.
  • I'm out of ideas.
Cons
  • Regular season really doesn't matter now other than the rivalry games
    • Top cartel teams can lose three games and still make the playoff
  • Going to start resting players?
    • The playoff is going to be *checks notes* several games!
    • Resting players could make games dumb.
    • Maybe even restrict NIL players from games played.
  • How much are streaming sub costs going up a month to pay for this?!
AZ.
AZ.
24 team playoff seems to be real close.

Are we really that far from a 64-team tournament?

The benefit of the 24 team playoff:
  • All the cartel teams that cartels want in playoff are in playoff
    • Independent of record too! Bonus.
  • MONEY!!!!! for the cartels.
  • I'm out of ideas.
Cons
  • Regular season really doesn't matter now other than the rivalry games
    • Top cartel teams can lose three games and still make the playoff
  • Going to start resting players?
    • The playoff is going to be *checks notes* several games!
    • Resting players could make games dumb.
    • Maybe even restrict NIL players from games played.
  • How much are streaming sub costs going up a month to pay for this?!
One of the pro's I see is in a year with so many undefeated teams they have a good chance of an opening. Few years back you had lower divisions that didnt get a shot. I love collage football and I have no problem with that addition.

We are in what week 5 now? Been two real good ranked games to watch.....Other than that top 25 teams are playing nothing.
Jimbo
One of the pro's I see is in a year with so many undefeated teams they have a good chance of an opening. Few years back you had lower divisions that didnt get a shot. I love collage football and I have no problem with that addition.

We are in what week 5 now? Been two real good ranked games to watch.....Other than that top 25 teams are playing nothing.
There are 68 Power 4 teams, so eventually they will get there I wouldn't imagine ...
AZ.
AZ.
There are 68 Power 4 teams, so eventually they will get there I wouldn't imagine ...
Far from it but you know that....You dont like the larger playoff.....Its ok.....
Jimbo
Far from it but you know that....You dont like the larger playoff.....Its ok.....
Oh, I Hate the idea ...

It would be different if it was a game that you could play 2 or games each week, but when you only play 1 game a week, the larger playoff is Not a good thing ...

The season has how many games now, is it 14 ... then you want to play another 5 (with more to come) against Top 12 (eventually 24 teams) ... remember, the 5 games in the playoffs will be the hardest games all year and back to back.

For example, IF Ohio State should win it all this year ... they play 5 teams in the Top 25, plus they would play 5 more to win it all, depending on how the ranking shake out and if Bye weeks are given.

Thats 10 Ranked teams ... in one year ...
I don't see that happening very often ...
Edit, Bama plays 4, Georgia plays 3, But Ole Miss plays 5 (didn't expect to see that)

That said, I don't see the Buckeyes winning it all this year.
  • Like
Reactions: AZ.
AZ.
AZ.
Oh, I Hate the idea ...

It would be different if it was a game that you could play 2 or games each week, but when you only play 1 game a week, the larger playoff is Not a good thing ...

The season has how many games now, is it 14 ... then you want to play another 5 (with more to come) against Top 12 (eventually 24 teams) ... remember, the 5 games in the playoffs will be the hardest games all year and back to back.

For example, IF Ohio State should win it all this year ... they play 5 teams in the Top 25, plus they would play 5 more to win it all, depending on how the ranking shake out and if Bye weeks are given.

Thats 10 Ranked teams ... in one year ...
I don't see that happening very often ...

That said, I don't see the Buckeyes winning it all this year.
Yes anyone here knows you 100%....Astros failed no posting...Ohio state loses we hear it.....Its ok....Its called an opinion....I have one so do you.....Problem is?
  • Like
Reactions: meStevo and Yespage
Jimbo
Yes anyone here knows you 100%....Astros failed no posting...Ohio state loses we hear it.....Its ok....Its called an opinion....I have one so do you.....Problem is?
Seeing theres very little activity in the MLB threads, it wouldn't matter if I posted that the Astros didn't make the Playoffs ...

Theres more NFL info in the Pub section than in the Sports/NFL thread.
  • Haha
  • Like
Reactions: meStevo and AZ.
Y
One of the pro's I see is in a year with so many undefeated teams they have a good chance of an opening. Few years back you had lower divisions that didnt get a shot. I love collage football and I have no problem with that addition.
A 12 team playoff net should catch any undefeated team. The 12 team playoff also exposed that rankings suck. I mean, we kind of knew already that the rankings weren't particularly reproducible, but we now have the empirical evidence that the rankings suck because judging who is the best among a mickey mouse scheduled football season isn't a rational endeavor. So the 12 team playoff ensures most teams that should make it, do, including the mid-major undefeated team. 8 teams should be able to work as well, but puts greater risk at OSU and Alabama missing the playoff... can't have that.

Which is the run up to my main problem with the 24 team set up is that it is designed to keep the OSU's and Alabama's from missing the playoff. The cartels are ensuring widespread participation for their own cartels to increase the monetary reward to themselves. It is fixing the system while not fixing the outcomes, merely making the regular season game outcomes virtually irrelevant. Sure, a bye for winning the conference would be nice, but we've already seen that byes aren't that influential.
We are in what week 5 now? Been two real good ranked games to watch.....Other than that top 25 teams are playing nothing.
That is college football in a nutshell. Again, college football isn't about competition, it is about revenue. The entire setup is about making money, from regular season squash games against local jobbers like the WWF days to tax exempt bowl games.

And to add to the first world woes, the college football cartels have made being a College Football fan even more expensive... so they can get paid more.
  • Like
Reactions: osu1991 and AZ.
meStevo
Theres more NFL info in the Pub section than in the Sports/NFL thread.

Nah, you just don't understand how ignore works, which is why you made your own NFL thread thinking there wasn't one 🤣
Foxbat
They ought to have fun with this… :devilish
  • Like
Reactions: osu1991
osu1991
They ought to have fun with this… :devilish
Was thinking same thing. It should be a good week for sec shorts and roll call
meStevo
Lifetime Supporter
Last reply · posted in The Chit Chat Club
A continuation of a thread from the pub, just general discussion of AI.

Brief 60 minute clip about next gem autonomous fighters - not remote controlled, but rather collaborating with controllers and aircraft in the theater.


View: https://youtu.be/DRm0mbp_n1k


We've literally got a movie already about this ;)


View: https://youtu.be/a2PW7a9ViDc
62 Replies · 1057 views
meStevo
Agreed, it mostly regurgitates known solutions. That's the point. Nobody needs an innovative fix for a driver error or a creative way to format a report. Let it handle the solved problems so people can spend their time on the ones that aren't.
harshness
Agreed, it mostly regurgitates known solutions. That's the point.
That's the point at which innovation ends, and there's no longer any point to software engineering other than swatting bugs that result from misapplication.
meStevo
That's the point at which innovation ends, and there's no longer any point to software engineering other than swatting bugs that result from misapplication.

Addressed by what you didn't quote. This cycle is as old as computing: compilers, libraries, frameworks each automated the tedious part, and the human work moved up a level. Innovation didn't end; it shifted. And people still make new compilers, libraries or frameworks.

Nobody's forced to hand anything off. Anyone who wants to keep doing it by hand still can, and people who couldn't do it at all now can.
harshness
... and people who couldn't do it at all now can.
Misapplication isn't something that the casual coder can identify. They can only discover, the hard way, that it doesn't work at some point.
meStevo
Misapplication isn't something that the casual coder can identify. They can only discover, the hard way, that it doesn't work at some point.
You're not wrong, but that's part of learning. Whether from others or our own mistakes, we've all learned that lesson one way or another.
harshness
Whether from others or our own mistakes, we've all learned that lesson one way or another.
I'm not sure that the school of hard knocks is the quickest or surest education to find your way.

There are many examples in the headlines of people getting burned multiple times and not wavering in their pursuit of stupidity.
meStevo
I'm not sure that the school of hard knocks is the quickest or surest education to find your way.

Good thing not everyone will have to learn the hard way then. The same tools can explain why something broke.

There are many examples in the headlines of people getting burned multiple times and not wavering in their pursuit of stupidity.

This is true of literally anything, though.

Happy to agree to disagree, but I'm already enjoying the dividends personally and helping others at work and at home do the same.
  • Like
Reactions: telstar_1
harshness
This is true of literally anything, though.
Do you think that means we ought to be supporting it as the long-term solution?
Foxbat
​
Foxbat
Oops.
dishstaller
Pub Member / Supporter Lifetime Supporter
Last reply · posted in The Chit Chat Club
I was watching some of this guy's stuff and realized some of you may not be familiar. Basically his show is Candid Camera meets a magician. This is a comp of a few of his exploits. I first learned of him when I was out at a meeting in Denver about 10yrs ago. The men I was sitting at the table with started talking about this show and said it was one of the funniest things they had seen. When I got home I started watching it....yes, it is funny.


View: https://www.youtube.com/watch?v=gIU09F8jdwc
2 Replies · 56 views
  • Like
Reactions: Jimbo
dishstaller
This one however is my all time favorite. Look at the way this guy holds the drill when he starts freaking out.


View: https://www.youtube.com/watch?v=Xt5DpFBtZwk&pp=ygUXY2FyYm9uYXJvIGVmZmVjdCByb21sZXk%3D
dishstaller
Gary Toma
Staff member Pub Member / Supporter Cutting Edge
Last reply · posted in DIRECTV Technical Resources Forum
The TPN Map Excel Presents all DIRECTV Channels:
​
National (50-States or wide/NAT+PR beams)
Local (Local-Into-Local or narrow/Spot beams)
​
Additional tabs provide:​
OTA the (Over-The-Air) Database
VOD (Video On_Demand) Records
Offline Records
Engr Records
Net Decoder a graphic presentation of all satellites and transponders
​
Domestic Satellites
@99W...... D11, D14
@101W.... D16
@103W.... D12, D15
@110W.... D5
@119W.... D8​

Understanding the TPN Map

Making Sense of the TPN Map Display Conventions
2142 Replies · 929865 views
K
Now testing on the stream server:
WJBF-D2 CW Augusta GA
KSVI-D2 CW Billings MT
WETM-D2 CW Elmira NY
WJET-D2 CW Erie PA
KLFY-D2 CW Lafayette LA
KARD-D2 CW Monroe LA
WVBT-D2 CW Norfolk VA
WTWO-D2 CW Terre Haute IN
WFXV-D2 CW Utica NY
KFDX-D3 CW Wichita Falls TX
K
PISTONS and THUNDER are finally testing on the stream server. PISTONS is showing the Ion/Scripps Sports promo loop filler that their NHL and WNBA feeds have, THUNDER has a "You are watching Thunder+" slate

The Clippers still haven't officially announced their TV plans beyond 10 simulcasts on KTLA, but the NBA's FAQ for ClipperVision is now live. The CLIPPERS feed is currently showing a loop of their Hawaii preseason game.

The Heat still haven't announced their West Palm Beach or Fort Myers affiliates. Since WPLG is streaming the games for free via their app, I doubt we'll be seeing the return of WPLG on stream.

So far nothing testing for the Bucks, Magic, Hawks or Hornets.
K
WETM-D2 CW Elmira NY
WJET-D2 CW Erie PA
KLFY-D2 CW Lafayette LA
KARD-D2 CW Monroe LA
WVBT-D2 CW Norfolk VA
WTWO-D2 CW Terre Haute IN
WFXV-D2 CW Utica NY
KFDX-D3 CW Wichita Falls TX
These are now live on stream and weren't testing on satellite as of yesterday:
WETM-DT/19 CW Elmira
WJET-DT/25 CW Erie
KLFY-DT/11 CW Lafayette LA
KARD-DT/15 CW Monroe
WVBT-DT/44 CW Norfolk
WTWO-DT/3 CW Terre Haute
WFXV-DT/34 CW Utica
KFDX-DT/4 CW Wichita Falls
K
The Heat still haven't announced their West Palm Beach or Fort Myers affiliates. Since WPLG is streaming the games for free via their app, I doubt we'll be seeing the return of WPLG on stream.
West Palm Beach is getting it on WTCN-CD/43 MNT. Still nothing for Fort Myers


Also, the Thunder's deal for KSBI/52 OKC and KQCW/19 Tulsa will be via a special cable and DIRECTV only feed of those stations. OTA viewers and Dish customers will be limited to 10 games.
dtv757
Thanks for the updates on CW norfolk
Hopefully comes to sat soon!!
dtv757
Not seeing 44 (WVBT-DT/44 CW Norfolk ) on my D* app for firestick
K
It's only available for streaming customers, they still haven't added that batch of CW stations to satellite.

Even if it was, satellite customers still can't stream their CW affiliates via the app, just the Big 4, select PBS stations and some independents (mainly the ones that have full season NHL/NBA rights)
  • Like
Reactions: Mr Tony
TheRatPatrol
Last reply · posted in TV Shows
Anyone else watch this show? Any guesses as to what was in the box Gibbs gave to Abby that was on her desk? It look liked it was glowing.

I also heard that someone was leaving the show at the end of this season. Any guesses as to who thats going to be?
2135 Replies · 214821 views
Jimbo

Howard ...
You don't like Tony, or Tony as the Director (he's only been there for 30 seconds now) or you don't like NCIS ?
  • Like
Reactions: Howard Simmons
Howard Simmons
Howard ...
You don't like Tony, or Tony as the Director (he's only been there for 30 seconds now) or you don't like NCIS ?
Tony as the director.🙄
Jimbo
Tony as the director.🙄
Would you rather have LaRoche ???
  • Like
Reactions: Howard Simmons
Howard Simmons
Would you rather have LaRoche ???
No. Bring in someone new.🤔 Tony is not serious enough for me. Parker is too close to the team and Tim is too young to take over IMO.
Jimbo
No. Bring in someone new.🤔 Tony is not serious enough for me. Parker is too close to the team and Tim is too young to take over IMO.
I don't think Tim and Tony are that far apart in Age ...

Remember what Tony said to Tim when they first got back together ...
Tony said: I am the New Tony, Tim .... (something to that effect)

Tony has changed, he's been running his Security Business ... I'm sure he has grown up.

Give it time ... your judging the New Tony from the old Tony.

It sounds like Tim won't be around the Team much longer either.
  • Like
Reactions: Howard Simmons
KAB
KAB
I wonder it they will show the teased meeting (in Origins) with Tony and Gibbs.
Jimbo
I wonder it they will show the teased meeting (in Origins) with Tony and Gibbs.
I'm curious how they are going to implement Tony into Origins (If they do) ...
Tony was introduced to Gibbs and the team, on NCIS, which makes it the Mothership side of things, he worked in Baltimore prior to NCIS, NO mention when they met that anyone had known one another ...
  • Like
Reactions: Howard Simmons
Jimbo
I wonder it they will show the teased meeting (in Origins) with Tony and Gibbs.
Teased Meeting ?