Social Feed

chapelrun
Pub Member / Supporter
Last reply · posted in Free To Air (FTA) Discussion
I finally broke down and replaced my trusted SV-HD8000 with an OPENBOX S9.

I would like to document how I setup my receiver - - as I had a few gotca's.

First off, as others have noted mine came with Firmware HDS2-10-11-08:1026CM which is from November 8th 2010. I just left that alone since it came from the Factory like that and it seems like a pretty good load.

The second thing I did was updated the Satellite List to the American list here. This is needed because mine came with only European Satellites.

http://www.satelliteguys.us/free-ai...s9-hd-factory-website-latest.html#post2382988

Next I went to this screen - - go to the second icon down on the left (Sat Dish) and select "Installation Antenna & satellite Quick Setting"

Lat-Long.jpg

Here you can input your Lat - Long or really in this case you Long - Lat. As others have noted in order to save arrow up and down and also you must arrow down off the Long before it will allow you change it to W.

Then choose the appropriate setting for your motor - - or if you have no motor pick the last setting.

At this point some of your items will be grayed out - - - such as "Single Satellite Scan" and all the ones below that. This confused me for a bit so here is what you do. Select "Satellite List" and that will show you this screen.

Sat-List.jpg

You can use your up and down arrow and by hitting the OK button you can put check marks beside the satellites that you can see in your configuration. After all this is set correctly you can hit the EXIT button and and all your items should now NOT be grayed out.

Next you will need to go to each satellite and change your "LNB Freq" and other settings as appropriate for you setup. Here is what one of my screens looked like.

Ant-Setup.jpg

Once all this was setup correctly - - - what I did was select "Single Satellite Scan" and I scanned each satellite East to West. This took several hours and looks like this.

Single-Sat-Scan.jpg

Once this is complete you should have all your channels in your receiver. Then you need to do some cleanup. I found this thread by Phottoman to be very helpful and would highly recommend it!

http://www.satelliteguys.us/free-air-fta-discussion/238731-how-use-editor-openbox-s9-hd.html

Other gotca's that have come up both for me and many others.

Beware of the V-FORMAT button - - some have even disabled it by taking the remote apart. I may have to do this because this remote will not be kid or wife friendly as is.

The plug I think is either European or some other country. I'm using the adapter that came with it and have rubber-banded it together. I think Lone Gunman cut his plug off and replaced it with a US plug. I may also have to do that.

Last item that I'm still having trouble with is getting my motor to go over to 15W. My Longitude is 78W and my SV-HD8000 had no trouble driving it all the way over to 15W but this receiver even in DiSEqC 1.2 will not drive all the way over.

Like I said I have only had this receiver for a couple days and really like it so far. The main reason I did this post is that all the information is here on SatGuys - - - just not in one place. Hope this helps others. :up
5 Replies · 5140 views
charper1
Thanks for this thread; where did you buy your Openbox
chapelrun
I purchased mine from Shop4FTA in San Gabriel, CA. I looked many other places but this was one of the cheapest, free shipping and came with this newest remote. (shown here)
charper1
Thanks. I wanted to make sure to buy from a reputable place AND get the v3 remote. I am hoping to get back into a house soon and back into FTA; I miss it.
chapelrun
May have been posted before but - - - I opened my OPENBOX :) and there is just not much to it. Here is a PIX.
B
Interesting post, thanks. I never could figure out how to get the Longitude setting to go from E to W, but since I was only concerned with one satellite I set it up manually and left the setting on East. I thought it was just a problem with my box. I also couldn't figure out how to use that power cord adapter, you would think it would just plug in and have a nice tight connection, but no..... so like the fellow mentioned above I just cut the plug off and replaced it with an American plug.

About the remote, I needed one to use in another room, and I couldn't find the v3 version, so I bought the earlier one. It works great, and I actually like it more than the v3. The V-Format button is up in the upper RH corner, and completely out of the way.
meStevo
Lifetime Supporter
Last reply · posted in The Chit Chat Club
Continuing the Kilauea thread in the Pub here. Perhaps the Iceland one too next time there's remarkable activity.

Currently there is precursory lava flowing into the crater, leading to the next episode that'll probably start within the next day.

You can see the pace of inflation / deflation here. It serves as the primary predictor for when the expect the eruptions, which coincide w/ inflation turning into significant deflation and last for several hours on average with significant fountaining.



View: https://youtu.be/Uecu2seh4b4


Wife and I like the AfarTV feeds, for the discussion along w/ them, though they're otherwise just mirrors of the official USGS feeds.


View: https://youtu.be/iws3rh5vLAQ
118 Replies · 3215 views
  • Like
Reactions: osu1991
meStevo

View: https://youtu.be/tv37YPVfHME


Gemini summary:

In this video from Shawn Willsey: Geology Explained, geology professor Shawn Willsey details rapid subsurface and surface changes at Kīlauea volcano in Hawaii:
  • Signs of a Magma Intrusion (Dike): Summit tiltmeters recorded an unprecedented, rapid inflation spike of around 45 microradians [04:00 Opens in a new window ], accompanied by a dramatic surge of over 100 shallow earthquakes within 24 hours (peaking at a magnitude 3.4) [01:44 Opens in a new window ]. The deformation indicates that magma is intruding in an east-west orientation beneath the southern caldera/Halemaʻumaʻu region [01:16 Opens in a new window ].

  • No Rift Zone Migration: Tilt and seismic data confirm magma is remaining confined to the summit area rather than traveling down the East Rift Zone [02:40 Opens in a new window ].

  • Structural Pathways: Willsey notes that pre-existing faults and fractures expanded during the 2018 caldera collapse [08:32 Opens in a new window ]. Because these fracture zones remain unsealed, magma can move and mobilize toward the surface much faster than before [10:17 Opens in a new window ].

  • Potential Outcomes: The intrusion could stall underground without erupting, or it could feed a new east-west fissure eruption inside the summit caldera, similar to the September 2023 event [02:47 Opens in a new window ].

  • Shift to Dome Overflows: Webcam footage from overnight reveals repeated pulses of fluid lava overflowing the spatter cone at the North Vent [11:42 Opens in a new window ]. Occurring roughly every 20 to 50 minutes and lasting several minutes each [12:36 Opens in a new window ], these cyclic overflows suggest Kīlauea may be transitioning away from high-fountaining episodes toward regular surface overflows [14:54 Opens in a new window ].

Foxbat
​
  • Like
Reactions: RaiderPower
Foxbat
​
Foxbat
Oooo, quite the show now. All three vents have doming and overflows. The cone that built up around the North vent lost its upper quarter at 02:50 Oct 17 and is now spewing lava at a healthy rate. Don't know if I would say it's a fountain, but it's close.


IMG_1534.webp

edit: The USGS has called the official start of Episode 55 as starting at 03:19 HST Oct 17, 2026:

Alert Level: WATCH, Color Code: ORANGE 2026-10-17 13:43:56 UTC
HVO/USGS Volcanic Activity Notice

Volcano: Kilauea (VNUM #332010)

Current Volcano Alert Level: WATCH
Current Aviation Color Code: ORANGE

Issued: Saturday, October 17, 2026, 3:43 AM HST
Source: Hawaiian Volcano Observatory
Notice Number: 2026/H488
Location: N 19 deg 25 min W 155 deg 17 min
Elevation: 4091 ft (1247 m)
Area: Hawaii

Summary: Episode 55 of the ongoing Halemaʻumaʻu eruption began at 3:19 AM HST on October 17, 2026.

Volcanic Activity:
Episode 55 of lava fountaining in Halemaʻumaʻu began at the summit of Kīlauea began at 3:19 AM HST on October 17, 2026.

Fountain heights are relatively low at about 100-150 feet (30-45 m), and it is not clear whether this episode will evolve to the same heights as previous episodes. Continuous overflows from the vents began yesterday, October 16, just before 6 a.m. HST and transitioned into episode 55 fountains at 3:19 a.m. HST this morning. The current forecast is for winds are blowing from the north-northeast direction, which suggests that volcanic gas emissions and volcanic material may be distributed to the south-southwest direction from Halemaʻumaʻu.
  • All eruptive vents and lava flows are confined to Halemaʻumaʻu crater within Hawaiʻi Volcanoes National Park. Tephra fall from volcanic ash clouds is greatest within 3 miles (5 km) of the vents, lighter ash and Pele's Hair may stay suspended for large distances from the vents.
  • Like
Reactions: thomasjk
Van
Van
Last reply · posted in What's Cooking?
Who says dinner or lunch has to be the only good meals of the day?

Honey butter grits with scrambled eggs and grilled boneless pork ribs on flakey biscuits washed down with cranberry juice.
6629 Replies · 379357 views
dfergie
Egg, sausage and cheese sandwich between bread toasted in butter in skillet... Chocolate milk.
  • Love
Reactions: TRG
dfergie
Egg, sausage and cheese sandwich between bread toasted in butter in skillet... Chocolate milk.
Add fresh hash browns, delete chocolate for milk with a slice of bacon.
  • Like
Reactions: Mr Tony and TRG
TRG
TRG
Bacon, eggs, hash browns and toast. Coffee.
  • Like
Reactions: Mr Tony and dfergie
TRG
TRG
Wound up at the Waffle House this morning. Got the two egg breakfast with coffee.

1622.webp
  • Like
Reactions: dfergie and Mr Tony
dfergie
Speaking of waffles, I'm going to put my mini waffle iron on stove so I'll remember to make waffles in the morning... Had some last week, been awhile.
dfergie
Dos cackleberrys over easy on top of 2 corned beef hash patties fried in skillet... Chocolate milk.
dfergie
Staff member HERE TO HELP YOU!
Last reply · posted in What's Cooking?
Anyone making their own breakfast sausage? I've recently been trying different recipes, found some I like, some I've modified...
38 Replies · 3552 views
  • Like
Reactions: spongella
navychop
Bob Evans Sage.
R
Bob Evans Sage.
I will look, but I don't think I have seen it. Owen's breakfast sausage use to be favorite, but I can't find it anymore. Jimmy Dean's country mild is OK also when I can find it.
  • Like
Reactions: navychop
dfergie
Swaggerty's isn't too bad, sausage prices are lower per lb than making my own from pork butts right now so I've been buying JC Potter or Owen lately.
(Swaggerty's at Sam's is pre cut, I usually partially freeze the rolls and cut with my slicer and vacuum seal on parchment paper)
  • Like
Reactions: navychop
S
I will look, but I don't think I have seen it. Owen's breakfast sausage use to be favorite, but I can't find it anymore. Jimmy Dean's country mild is OK also when I can find it.
amazon maybe :what
S
I will look, but I don't think I have seen it. Owen's breakfast sausage use to be favorite, but I can't find it anymore. Jimmy Dean's country mild is OK also when I can find it.
owens on amazon is 54.99 for a 4 pk 16 oz a sausage. i feel that's kind of steep!!!
S
Swaggerty's isn't too bad, sausage prices are lower per lb than making my own from pork butts right now so I've been buying JC Potter or Owen lately.
(Swaggerty's at Sam's is pre cut, I usually partially freeze the rolls and cut with my slicer and vacuum seal on parchment paper)
id'e rather make my own vs store bought.
  • Like
Reactions: dfergie
R
owens on amazon is 54.99 for a 4 pk 16 oz a sausage. i feel that's kind of steep!!!
Especially when I can get a two pound roll of Jimmy Dean from Sam's Club for $7.38.
dfergie
They run Owens at $3.99 for lb and $7.99 a couple times a month at some grocery stores here, I actually was wrong, just checked a pork sirloin roast it was $1.99 a lb. (cooked it yesterday so pack was in trash)
Scott Greczkowski
Staff member HERE TO HELP YOU! Cutting Edge
Last reply · posted in The Chit Chat Club
Sometimes a thread gets so many posts in it that is can cause issues for the server so that why today we introduce The Song Name Game Part 3!

So let the game continue!

The last song was added by Bobby who posted...

One Meat Ball - Andrews Sisters

CONTINUE ON AND HAVE FUN! WELCOME HOME TO SATELLITEGUYS.US!

Here are the original rules for the game as posted by WebbyDude back in 2006. http://www.satelliteguys.us/threads/68645-Song-Name-Game

Just name a song title and the band who performed it. The next person does the same thing, but needs to list a song title or band name which includes a word from the previous entry. Pick songs from any genre.

Example:

Long Live Rock and Roll -- Rainbow

Rainbow in the Dark -- Dio

Another example:

Ride the Lightning -- Metallica

Lightning Strikes -- Ozzy Osbourne


Get it?


An additional note: we all know that song titles, sometimes, use profane words. Because this is a family friendly website it is advised that you clean up that title up a bit. This is accomplished by using something like sh!t instead of the real word. Thanks....
68508 Replies · 2671497 views
  • Like
Reactions: c-spand
EatMyVolts
Smoke! Smoke! Smoke! (That Cigarette) -- Tex Williams
long_time_Dish
Don't Do Me Like That - Tom Petty & The Heartbreakers
H
I LIKE It LIKE THAT-The Dave Clark Five
  • Like
Reactions: ClarkGable
ClarkGable
Five O'Clock World - The Vogues
FTA4PA
Six O'Clock News - John Prine
TheRatPatrol
Last reply · posted in TV Shows
Anyone else watch this show? Any guesses as to what was in the box Gibbs gave to Abby that was on her desk? It look liked it was glowing.

I also heard that someone was leaving the show at the end of this season. Any guesses as to who thats going to be?
2134 Replies · 214750 views
Jimbo

Howard ...
You don't like Tony, or Tony as the Director (he's only been there for 30 seconds now) or you don't like NCIS ?
  • Like
Reactions: Howard Simmons
Howard Simmons
Howard ...
You don't like Tony, or Tony as the Director (he's only been there for 30 seconds now) or you don't like NCIS ?
Tony as the director.🙄
Jimbo
Tony as the director.🙄
Would you rather have LaRoche ???
  • Like
Reactions: Howard Simmons
dfergie
I liked this episode and a toned down Tony...
  • Like
Reactions: Jimbo
Howard Simmons
Would you rather have LaRoche ???
No. Bring in someone new.🤔 Tony is not serious enough for me. Parker is too close to the team and Tim is too young to take over IMO.
Jimbo
No. Bring in someone new.🤔 Tony is not serious enough for me. Parker is too close to the team and Tim is too young to take over IMO.
I don't think Tim and Tony are that far apart in Age ...

Remember what Tony said to Tim when they first got back together ...
Tony said: I am the New Tony, Tim .... (something to that effect)

Tony has changed, he's been running his Security Business ... I'm sure he has grown up.

Give it time ... your judging the New Tony from the old Tony.

It sounds like Tim won't be around the Team much longer either.
KAB
KAB
I wonder it they will show the teased meeting (in Origins) with Tony and Gibbs.
  • Like
Reactions: reubenray
Jimbo
I wonder it they will show the teased meeting (in Origins) with Tony and Gibbs.
I'm curious how they are going to implement Tony into Origins (If they do) ...
Tony was introduced to Gibbs and the team, on NCIS, which makes it the Mothership side of things, he worked in Baltimore prior to NCIS, NO mention when they met that anyone had known one another ...